WyreStorm TX-35-IW 4K UHD HDBaseT 1-Gang In Wall Transmitter User Guide

: June 5, 2024
: WyreStorm

Table of Contents

In the Box
Basic Wiring Diagram
TX-35-IW (Front/Rear)
Wiring and Connections
- IR Wiring
- RS-232 Wiring
Troubleshooting
Warranty Information
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Quickstart Guide
4K UHD HDBaseT 1-Gang In Wall Transmitter (4K: 35m/115ft | 1080p: 70m/230ft)
TX-35-IW

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation process.

IMPORTANT! Installation Requirements

Visit the product page to download the latest firmware, document version, additional documentation, and configuration tools.
Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
While this product supports CEC, WyreStorm cannot guarantee compatibility with all forms of CEC communication.

In the Box

1x 2 pin Phoenix Male Connector
2x 3 pin Phoenix Male Connector
1x 1-Gang Decora Wall Plate
Device powers via PoH (12V 2A DC PSU Sold Separately)
1x Quickstart Guide (This Document)

Basic Wiring Diagram

TX-35-IW (Front/Rear)

WyreStorm TX 35 IW 4K UHD HDBaseT 1 Gang In Wall Transmitter -
Front | WyreStorm TX 35
IW 4K UHD HDBaseT 1 Gang In Wall Transmitter - Rear
---|---
A IR Window| | A HDBT Out| 8-pin RJ-45 female
Connect the transmitter’s HDBT OUT to the receiver’s HDBT IN.
---|---|---|---
B HDMI Input| 19-pin type A HDMI female
Supports HDMI and DVI/D with an adapter| B Power Input| 2-pin Phoenix: 12v Power Input
C Power LED| Solid: The unit is powered On
Off: The unit is powered Off| C RS-232| 3-pin phoenix for passthrough to RX
D Link LED| On: Indicates link established with receiving device
Off: No link with receiver or receiver powered off| D IR| 3-pin phoenix for passthrough to RX

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on the signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
WyreStorm recommends using pre-terminated HDMI cables due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.

WyreStorm TX 35 IW 4K UHD HDBaseT 1 Gang In Wall Transmitter - Wiring
Guidelines

IR Wiring

The 3-pin IR connector can be used to either transmit or receive IR signals, based on the type of cable and pinout you use. The IR emitter or receiver being used must support 5v for proper operation.

WyreStorm Connector		3rd Party Device
Pin 1	5v (Receive)	—> To —>
Pin 2	IR (Transmit)	—> To —>
Pin 3	G (Ground)	—> To —>

RS-232 Wiring

The TX-35-IW uses a 3-pin RS-232 with no hardware flow control. Most control systems and computers are DTE where pin 2 is RX, this can vary from device to device. Refer to the documentation for the connected device for pin functionally to ensure that the correct connections can be made. Refer to RS-232 Mode Settings for details on setting RS-232 modes.

WyreStorm Connector		3rd Party Device
Pin 1	TX (Transmit)	RX (Receive)
Pin 2	RX (Receive)	TX (Transmit)
Pin 3	G (Ground)	G (Ground)

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

Verify that power is being supplied to the transmitter and receiving device.
Verify that all HDMI and HDBaseT connections are not loose and are functioning properly.
Verify that the HDBaseT cable is properly terminated following the EIA568B standard.
Verify that the output resolution of the source and display is supported by this extender.
If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

Verify that the RS-232 cables are properly terminated following the Wiring and Connections section.

Troubleshooting Tips:

WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.

Note: WyreStorm reserves the right to change the product specification, appearance, or dimensions of this product at any time without prior notice.

Warranty Information

WyreStorm Technologies LLC warrants that its products be free from defects in material and workmanship under normal use for a period of five (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.