WyreStorm RX-35-POH 4K UHD HDBaseT Receiver with Bidirectional IR User Guide

WyreStorm RX-35-POH 4K UHD HDBaseT Receiver with Bidirectional IR

Quickstart Guide

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the installation process.

IMPORTANT! Installation Requirements

•  Visit the product page to download the latest firmware, document versions, additional documentation, and configuration tools.
•  Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
•  While this product supports CEC, WyreStorm cannot guarantee compatibility with all forms of CEC communication.

In the Box

• 1x RX-35-POH Receiver
• 1x 12V 2A Power Adaptor (US, UK, EU, AU) 1x IR Emitter
• 1x IR Receiver
• 2x Mounting Brackets
• 1x 3 Pin Phoenix Male Connector
• 1x Quickstart Guide (this document)

Basic Wiring Diagram

• Power LED Solid:  The receiver is powered
• On-Off: The receiver is powered Off Status LED
• Flashing: The receiver is operating normally.
• Off: The receiver is Not operating normally.
• HDCP LED Solid: HDCP content is present. Flashing:
• HDCP content is not present.  Off: No signal.
• LINK LED Solid: Link to receiver has been established.
• Flashing: Link to receiver has not been established.
• Power Input 5.5mm Screw Down Barrel Jack Connect to the included 12V DC 2A power supply to the transmitter or receiver. A power supply is not required on the other end as it will be powered using PoH.
• IR TX  IR TX – 3.5mm (1/8in) Mono Jack: Connect to the supplied IR emitter to control a local device from the remote display location via HDBaseT
• IR RXIR RX – 3.5mm (1/8in) Stereo Jack: Connect to the supplied IR receiver to send IR to the remote display location via HDBaseT. See IR TX/RX Guidelines for more information.
• RS-232 1x RS-232: 3-pin Phoenix
• HDBT In 8-pin RJ-45 female Connect the matrix HDBT Out to receivers HDBT In.
• HDMI Out 19-pin type A HDMI female Supports HDMI and DVI/D with adapter

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

•  The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
•  WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
•  WyreStorm recommends using pre-terminated HDMI cables due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure that most IR coding formats are transmitted and received Other 3rd party emitters and receivers can be used; however, these devices must operate in the same manner as the WyreStorm devices.
• Due to differences in IR across 3rd party control systems their IR ports should never be connected directly to a NetworkHD system as an incompatibility may exist. WyreStorm offers a cable that compensates for voltage differences as well adjusts for differences in the pins used within the port. Refer to the CAB-IR-LINK product page for more information.

IR TX Port Pinout

The connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs +5V DC to power the included IR receiver.

No or Intermittent 3rd party Device Control

•  Verify that the RS-232 cables are properly terminated.
•  Verify that emitters/receivers are compatible with WyreStorm IR.
•  If using an IR control system, verify that it is connected using the CAB-IR- LINK cable.

Specifications

Transmission

Output Video Encoding| HDBaseT Class B| | |
End to End Latency (Max)| 10μs (micro seconds)| | |
Decoding Data Rate| 10.2Gbps| | |
Audio and Video| | | |
Inputs| 1x HDBT In: 8-pin RJ-45 Female| | |
Outputs| 1x HDMI Out: 19-pin type A| | |
Maximum Pixel Clock| 297MHz| | |
| Video Resolution| HDMI| Cat6| Cat6a/7
| 1920x1080p @60Hz| 15m/49ft| 70m/230ft| 70m/230ft
| 3840x2160p @60Hz 8bit 4:2:0| 5m/16ft| 35m/115ft| 35m/115ft
| 3840x2160p @24Hz 10bit 4:2:0 HDR| 5m/16ft| 35m/115ft| 35m/115ft
| 4096x2160p @60Hz 8bit 4:2:0| 5m/16ft| 35m/115ft| 35m/115ft

Note:
WyreStorm reserves the right to change product specification, appearance or dimensions of this product at any time without prior notice.

Warranty Information

This product is covered by 5-year limited parts and labor warranty. During this period there will be no charge for unit repair, component replacement or complete product replacement in the event of a malfunction. The decision to repair or replace will be made by the manufacturer. This limited warranty only covers defects in materials or workmanship and excludes normal wear and tear or cosmetic damage. Visit the product page located at wyrestorm.com for additional information on this product including important technical information not provided in this document and warranty terms & conditions.

References

• WyreStorm - Professional Audio Visual Solution Provider

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>