POPPSTAR 5 Stuks Magneet Haken (Houdkracht 36 kg Instructions

POPPSTAR 5 Stuks Magneet Haken (Houdkracht 36 kg

SPECIFICATIONS

• hose diameter:                     11mm (1/2)
• inlet hose length:                  2m
• outlet hose length:               30m
• max. operating pressure:      8bar

1. READ THE ENTIRE GUIDE BEFORE INSTALLATION OR USE.
2. CONNECT ONLY TO WATER SOURCE WITH PRESSURE A T OR BELOW 8 bar.
3. RELEASE WATER PRESSURE WHEN NOT IN USE.
4. THE PRODUCT CONTAINS CHARGED SPRING. DO NOT DISASSEMBLE HOUSING

PACKAGE CONTENTS

1. A. Instruction Manual
2. B. Hardware pack
3. screw (x4)
4. Washer (x4)
5. plastic anchor (x4)
6. C. Hose reel
7. D. Mount Bracket
8. E. Mount pin

CHOOSING THE BEST MOUNTING LOCATION

This product can be mountedin many different ways. It is important to select your mounting location carefully. Consider mounting to surfaces…

1. Near your water source. This product includes 30m (98 ft) of outlet hose. Make sure you it can reach your work site.
2. Near your water supply. This product includes 2m (6ft) of inlet hose. Make sure it can reach your water supply.
3. Out of direct sunlight.
4. Strong enough to support the loads shown to the right (per screw). If unsure, contact a professional installer.
5. Refer to the installation options below for more detail.

INSTALLATION

WARNING: IF NOT PROPERLY INSTALLED, THERE IS A RISK OF FALLING. MAKE SURE YOUR INSTALLATION CAN SUPPORT THE LOADS ABOVE.
CAUTION: WHEN USING POWER TOOLS SUCH AS AN ELECTRIC DRILL, PLEASE WEAR EYE PROTECTION
WARNING: ENSURE THERE ARE NO LIVE ELECTRICAL WIRES OR PLUMBING IN THE WALL AT THE LOCATION YOUR ARE DRILLING.

DIRECT MOUNT TO WOOD STUD…Recommended tools…

• masking tape
• stud-finder
• bubble level
• electric drill
• Ø3mm (Ø1/8 in) drill bit Philips head screw driver

**Steps

**

1. Using stud-finder, locate stud and mark the location.
2. Tape the drilling template on the wall at a convenient height, making sure the holes are centered on the stud.
3. Check the hole centers with the level to ensure they  are plumb.
4. Drill (4) four holes with a Φ3mm (Φ1/8in) masonry drill bit on the template centers.
5. Fasten the mounting bracket with four screws and washer to the wall or timber post.
6. Hang the hose reel on the wall bracket, and secure it by inserting the mount tube.
7. Connect with inlet hose end with the water source.

MOUNT TO HOLLOW WALL AND MASONRY WALL

Recommended tools…

• masking tape
• bubble level
• electric drill
• Ø10mm (Ø3/8 in) drill bit
• hammer or mallet
• Philips head screw driver

Steps

1. Tape the drilling template on the wall at a convenient height, making sure the holes are between studs.
2. Check the hole centers with the level to ensure they are plumb.
3. Drill (4) four holes with a 10mm (3/8in) masonry drill bit on the template centers.
4. Tap plastic anchors (B.3) into holes with a hammer or mallet.
5. Fasten the mounting bracket with four screws and washer to the wall or timber post, and ensure drive mounting screws into the plastic anchors) in the wall.
6. Hang the hose reel on the wall bracket, and secure it by inserting the mount tube.
7. Connect with inlet hose end with the water source.

OPERATING INSTRUCTIONS

WARNING: ALWAYS HOLD THE HOSE REEL UNTIL IT COMPLETELY RETRACTS INTO THE HOSE REEL
WARNING: THE YELLOW TAPE MARKS THE END OF HOSE LENGTH
RELEASE PRESSURE WHEN NOT IN USE.

CAUTION: DO NOT RELEASE THE HOSE ALLOWING TO REWIND ON ITS OWN.

1. Pull the hose out to the desired length. The hose will automatically lock in position.
2. To unlock and retract, give the hose a short pull. Walk the hose back to the hose reel. If you pull the hose longer than 10cm you may re-lock the hose.
3. To avoid injury and damage, always hold the hose while it is retracting. This hose reel has a controlled return function.
4.  if the hose becomes tangled and will not retract – slowly pull out the hose past the tangled section and then allow the hose to slowly retract while guiding the hose back into the hose reel. Always ensure the hose is clean and not twisted.

ADJUSTING THE STOP-BALL

The stop-ball location can be adjusted to ensure the hose is always within reach.

Recommended tools…

No tool is needed

Steps

1. Pull out the hoes to the desired length, ensuring the hose re not rewind).
2. Open the latch on the stop ball and move it to the desired lo
3. Re-latch the ball .

CAUTION: ALWAYS MAKE SURE THE HOSE REEL IS LOCKED BEFORE REMOVING THE STOP-BALL, AND MAKE SURE THE STOP BALL IS SECURELY FASTENED BEFORE UNLOCKING THE REEL

MAINTENANCE

While your product has been made with high quality materials, degradation can occur over time. Inspect the hose and housing periodically. If cracking or blisters are visible, discontinue use.

PRODUCT CONTAINS CHARGED SPRING. DO NOT DISASSEMBLE HOUSING

1. Always keep the hose clean.
2. If the hose becomes dirty, clean it with a damp cloth while retracting.
3. DO NOT twist the hose while in use.
4. Mount the hose reel in a sheltered area to assist and protect the performance of the hose and the reel.
5. DO NOT allow the hose to contact any corrosive chemicals or fluids.
6. Always retract the hose when not in use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>