POPPSTAR 12 V DIN Rail Power Supply Instructions
- June 4, 2024
- POPPSTAR
Table of Contents
12 V DIN Rail Power Supply
Instruction Manual
Please read this manual carefully before using the DIN rail power supply.
ATTENTION: Failure to comply with the safety instructions and the
instructions for use listed here may result in serious accidents, personal
injury, and material damage.
Includes
DIN rail power supply slim, additional sheet linked with the manual
Specifications
Model| 1010425| I 1010426| I 1010427| I 1010428| I
1010429| I 1010430
---|---|---|---|---|---|---
Input| 100 – 240V AC, 50/60 Hz
Output| 5V 2A 10W| 12V 1,25A 15W| 12V 2,5A 30W| 24V 2,5A 60W| 12V 4,5A 54W|
12V 7,5A 90W
Adjustable output voltage| 4V – 6V| 11V – 13V| 11,4V – 12,6V| 22,8V – 25,2V|
11,4V – 12,6V| 11V -13V
Relative humidity| Operating: 20 – 90% (non-condensing)
Storage: 10 – 9596
Temperature| Operating: -20 to +50°C
Storage: -40 to +80°C
Appliance class| II
IP code| IP 20
Primary cable Secondary cable| 12 AWG -18 AWG (3,3mm2 – 0,8mm2)
Heat-resistant up to min. 80 °C (e. g. UL1007)
Dimensions (mm)| 18x 90x 58| 18 x 90 x 58| 78x 92 x 61| 52,5 x90 x 58| 52,5 x
90 x 58| 70 x90 x 58
Weight (g)| 72| 74| 234| 188| 186| 246
For installation on| DIN rail of type TS 35/7.5 or TS 35/15 (or similar)
Safety instructions
-
WARNING: Danger! All installation steps described here may only be carried out by experienced specialists who are trained and experienced in the installation as well as commissioning and maintenance of DIN rail power supplies combined with electromechanical components.
The same applies to 230 V mains by qualified electricians. -
WARNING: Electric shock hazard! Incorrect modifications to the Popstar DIN rail power supply may result in 230 V AC voltage being applied to other components.
-
WARNING: Short circuit hazard! Never insert objects into ventilation slots or sockets.
-
WARNING: Fire hazard! Selecting a higher operating voltage than specified by the manufacturer of the product can cause serious damage to the DIN rail power supply and the electronic devices connected to it!
-
For any work carried out on the 230 V AC mains, the current VDE regulations as well as corresponding country-specific regulations must be respected.
-
Incorrect wiring of the DIN rail power supply can lead to the destruction of the electronics.
-
Keep the product out of reach of children.
-
Contains small parts that can be swallowed. Keep away from small children!
-
Never open the housing.
-
Never cover the product.
-
Never expose the product to extreme circumstances such as heat, cold, wet, or humid environments, foreign matters (e. g. chippings or liquids), direct sunlight, vibrations, shocks, or mechanical pressure.
-
Do not modify or dismantle the product or accessories.
-
Never repair broken products yourself. Please contact our technical support.
-
Only use the product in dry indoor areas.
Installation
WARNING: Allowed mounting position: To ensure proper ventilation during operation, only vertical wall mounting is allowed for the DIN rail power supply. Horizontal mounting is not allowed.
- Mounting location: Keep the ventilation slots of the DIN rail power supply free at the top and bottom (20-40mm). Sufficient space around the power supply at the mounting location (5-10mm) must be provided in order for it to cool properly.
- Tilt the power supply slightly backward and place it on the rail from above.
- Push the power supply down as far as it will go.
- To lock the power supply in its place, press against the lower front until it clicks into the rail (it makes a click sound).
- Gently shake the power supply to check that it is securely attached.
Wiring
WARNING: Danger! The connection must be made in a voltage-free/load-free
state!
WARNING: Use separate wires for the inputs and outputs.
WARNING: The DIN rail power supply works as soon as the primary side is
receiving voltage. It does not have its own on/off switch.
We recommend checking the output voltage once with a multimeter before
connecting a device because an unwanted output voltage could damage or destroy
your device.
- Open all screw terminals (+, -, L, N) with a flathead or crosshead screwdriver.
- Route the cables in the cable holders and fasten the screw terminals again, so the cables are firmly secured.
- Check that the cables are firmly secured.
Adjusting the output voltage
Above the symbol “+V ADJ” on the power supply you will find the potentiometer for adjusting the output voltage (for values see table). The output voltage can be increased by turning it clockwise with a flathead or crosshead screwdriver.
Disassembly
WARNING: Before removing, switch off the main power supply, check that there is no voltage present and disconnect the power supply from the mains.
- Put a flathead screwdriver into the groove of the release slide (at the bottom of the power supply) and pull it downwards with it.
- Lift the lower front edge of the power supply carefully and remove it.
Malfunction
WARNING: A functional test may only be carried out by qualified
electricians.
Should a malfunction occur, check the following:
- Is the LED (“Output voltage OK”) lit (except 1010427)?
- Are the cables for the nominal input voltage (L, N) connected?
- Is the protective earth (PE) connected?
- Is the shielding/ground of the power supply cable connected to the device?
- Is the device connected to the output with the correct polarity?
- Has the correct cable diameter been selected?
- Is the nominal output voltage (5V/12V/24V, see table) correctly applied to the input of the device?
- Has the maximum output current been exceeded by too many devices?
Storage and maintenance
Store the product in a cool and dry place.
Use a dry and soft cloth for cleaning the product, do not expose it to
cleaning agents or chemicals!
Liability
Popstar GmbH is not liable for personal injury or property damage caused by
incorrect installation, use, or maintenance.
Instructions for disposal
Product:
According to the European WEEE Directive, electrical and electronic equipment
must not be disposed of with regular household waste. Their components must be
recycled or disposed of separately because toxic and hazardous components can
cause permanent damage to health and to the environment if disposed of
incorrectly.
As a consumer, you are obliged under the Electrical and Electronic Equipment
Act (ElektroG) to return electrical and electronic equipment free of charge at
the end of its service life to the manufacturer, the outlet or the public
collection points set up for this purpose.
Details are regulated by the applicable national law.
The symbol on the product, the instructions for use and/or the packaging
indicate these regulations. By separating, recycling, and disposing of old
appliances in this way, you are making an important contribution to protecting
our environment.
Packaging:
Packaging can be disposed of free of charge at the appropriate collection
points: paper in the paper bin, plastics in the plastic bin, and glass in the
correct glass container
EC Declaration of Conformity
By means of the CE symbol, Poppstar GmbH declares that the product complies
with the basic requirements and directives of European regulations.
Additional symbols on the product
Protective insulation: Appliance class II|
---|---
For indoor use only| ****
Power supply type: Switching power supply|
Short-circuit proof safety transformer (with fuse and thermal protection)|
Contact
Popstar GmbH
Heidelbergerstraße 49
74746 Höpfingen
Germany
E-Mail: info@poppstar.eu
Tel: +49 (0)6283 21570-27 (Mo.- Fr. 2 PM – 5 PM)
Live chat: www.poppstar.eu (Mo.- Fr. 8 AM- 5 PM)
Misprints and changes to the product, packaging, and product documentation are
reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>