Poppstar B09X5R9JDT TV Wall Mount TV Stand Instructions
- June 5, 2024
- POPPSTAR
Table of Contents
Poppstar B09X5R9JDT TV Wall Mount TV Stand Instructions
Safety instructions
Read the manual thoroughly. Keep the manual for as long as you use the product
and pass it on to later users or owners. Only use the product for its intended
purpose.
Caution: If used with TVs that exceed the maximum weight, this may result
in damage or injury. Make sure that your TV and any other accessories meet the
maximum weight capacity of the wall mount. Do not place the wall bracket
asymmetrically, as this may cause the weight capacity to be exceeded. Caution:
Choking hazard due to small parts that could be swallowed. Keep the product
away from children.
Preparation
Check the contents for missing parts and make sure that no parts are defective
or damaged.
This product is designed for use on vertical walls with wooden beams (minimum
51 x 102 mm) or masonry (solid concrete; density 2000 PSI). If you would like
to install it on a different type of surface, obtain special installation
equipment from a specialist shop.
Check that the desired mounting surface is suitable enough before installing.
Make sure that there are no electrical, water, gas or other lines near the
mounting location.
Install the product ONLY in places where there is no way of harming other
persons or animals by it falling or coming loose.
Mounting
Important notes
- Always have two people assemble and adjust the wall bracket.
- When assembling and disassembling, use work gloves and properly functioning tools to avoid injuries. Carefully trim sharp edges or remove splinters that appear when shortening cable ducts.
- When routing cables, make sure that the insulation cannot be damaged.
- After installing the wall bracket, check if the product is attached firmly and safely.
- The following tools are required (not included in the package):
- Pencil, measuring tape/inch rule, spirit level, hammer, large crosshead screwdriver, Ø4mm wood drill bit or Ø10mm masonry drill bit, ratchet with 12mm socket set.
Installation steps
-
Remove all cable covers and side covers from the wall bracket and put them aside. Unscrew the monitor support plate from the wall bracket (two short screws with nuts and the bottom right and left).
-
(A. For masonry:) Mark 6 fixing points on the wall (use the wall bracket as reference: 3 above, 3 below). Make sure that the points are aligned properly by using a spirit level. (B. For wooden walls:) Mark 4 fixing points at the height of the wooden beams (use the wall bracket as a reference: 2 above, 2 below). Make sure that the points are aligned properly by using a spirit level.
-
(A. For masonry:) Drill six holes approx. 80mm deep using a 10mm drill bit at the fixing points.
(B. For wooden walls:) Drill four holes approx. 80mm deep using a 4mm drill bit at the fixing points. -
(A. For masonry:) Press 6 dowels into the holes and secure the wall bracket with 6 screws. (B. For wooden walls:) Secure the wall bracket with 4 screws.
-
Slide the two longer support arms lengthwise into the monitor support plate and secure them tightly in the center with 2 turns, then, depending on the VESA size of the monitor, fasten the two short support arms to the long support arms with screws and nuts.
-
Screw the monitor support plate to the monitor with the support arms.
-
Important: 2 people are necessary! Lift up the monitor, insert the support plate from above into the monitor bracket and secure it with the two screws from step 1.
-
Lay the monitor cables along the wall bracket and put on the cable covers and the side covers.
-
Slightly loosen the two nuts at the top of the support plate, adjust the tilt (-5°/+8°) of the monitor as desired and secure. If you wish, you could rotate the monitor support plate slightly (+4°/-4°).
Cleaning
Clean the product with a dry or slightly damp cloth and a mild detergent. Do not use aggressive or abrasive cleaning agents, otherwise the surface may be damaged.
Maintenance
Check the wall bracket regularly for safety and stability (recommended to do every three months). In case of damage or instability, the wall bracket should no longer be used and should be dismantled.
Disposal
To protect it against transport damage, the product is delivered in packaging
made of recyclable materials. Dispose of it correctly in the containers that
are available to you. Contact your local waste disposal company or your
municipal administration to dispose of the product in an environmentally
friendly way.
Disclaimer
Popstar GmbH accepts no liability or warranty for damage resulting from
improper installation or assembly as well as improper use of the product or
failure to comply with the safety instructions. Important note: This product
does not fall under the Regulation (EU) No 305/2011 regarding construction
products.
Manufacturer information
Should you need any technical advice, please contact our technical support.
- Contact
- Poppstar GmbH
- Heidelbergerstraße 49
- 74746 Höpfingen
- Germany
- Email: info@poppstar.eu
- Tel: +49 (0)6283 21570-27 (Mo.- Fr. 2 PM – 5 PM)
- Live chat: www.poppstar.eu (Mo.- Fr. 8 AM – 5 PM)
- Misprints and changes to the product, packaging, and product documentation reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>