POPPSTAR F850 Wall Mount Instructions

: June 16, 2024
: POPPSTAR

Table of Contents

F850 Wall Mount
Safety instructions
Preparation
Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

F850 Wall Mount
Instructions

F850 Wall Mount

POPPSTAR F850 Wall Mount VESA
200×200 200×300 200×400
300×200 300×300 300×400
400×200 400×300 400×400
600×200 600×300 600×400

|
---|---

Safety instructions

Read the manual thoroughly. Keep the manual for as long as you use the product and pass it on to later users or owners. Only use the product for its intended purpose.
Caution: If used with TVs that exceed the maximum weight, this may result in damage or injury. Make sure that your TV and any other accessories meet the maximum weight capacity of the wall mount. Do not place the wall bracket asymmetrically, as this may cause the weight capacity to be exceeded.
Caution: Choking hazard due to small parts that could be swallowed. Keep the product away from children.

Preparation

Check the contents for missing parts and make sure that no parts are defect or damaged.
This product is designed for use on vertical walls in solid construction materials (concrete, masonry).
If you would like to install it on a different type of surface, obtain special installation equipment from a specialist shop.
Check that the desired mounting surface is suitable enough before installing. Make sure that there are no electrical, water, gas or other lines near the mounting location.
Install the product ONLY in places where there is no way of harming other persons or animals by it falling or coming loose.
Mounting
Important notes
Always have two people assemble and adjust the wall bracket.
When assembling and disassembling, use work gloves and properly functioning tools to avoid injuries.
Carefully trim sharp edges or remove splinters that appear when shortening cable ducts.
When routing cables, make sure that the insulation cannot be damaged.
After installing the wall bracket, check if the product is attached firmly and safely.
The following tools are required (not included in the package):
Pencil, measuring tape/inch rule, large crosshead screwdriver, Ø10mm drill bit, ratchet with 10mm socket set.

Installation steps (see instructions on images)

Use the wall bracket as a model and place it in the desired position on the wall.
Note: The arrow on the wall bracket has to point upwards. Ensure that the wall mount is properly straightened using the spirit level and mark six drill holes: Four at the top and two in the middle at the bottom. Continue to drill the holes approximately 60 mm deep at the fixation points using the 10 mm drill bit. Press the dowels (W-B) into the drilled holes. Mount the wall bracket to the wall using the washers, the screws ( W-A, W-C ) and the ratchet.
Choose the correct VESA screws for your TV (M-A, M-B, M-C, M-D or M-E). Fasten the two monitor rails to the monitor together with washers (M-F) and, if necessary, with spacers ( M-G, M-H, depending on the length of the screw and the threaded socket of your TV)
Take one of the two fastening nuts (C) and screw it onto the already mounted screw in the middle of the upper monitor rail.
Caution: This part requires two persons! Unfold the mounting parts hanging on the wall. Lift up the monitor and insert the upper monitor rail with the fastening nut into the notch of the bracket.
The mounted screw in the centre of the lower monitor rail should now fit through the hole in the mounting plate. Secure the screw using the washer (D) and the second fastening nut (C).
Make sure your TV screen is straightened accordingly using the spirit level. Should you wish to change this, slightly rotate it by loosening the lower fastening nut.

Cleaning
Clean the product with a dry or slightly damp cloth and a mild detergent. Do not use aggressive or abrasive cleaning agents, otherwise the surface may be damaged.

Maintenance

Check the wall bracket regularly for safety and stability (recommended to do every three months). In case of damage or instability, the wall bracket should no longer be used and should be dismantled.

Disposal
To protect it against transport damage, the product is delivered in packaging made of recyclable materials. Dispose of it correctly in the containers that are available to you. Contact your local waste disposal company or your municipal administration to dispose of the product in an environmentally friendly way.
Disclaimer
Poppstar GmbH accepts no liability or warranty for damage resulting from improper installation or assembly as well as improper use of the product or failure to comply with the safety instructions.
Important note: This product does not fall under the Regulation (EU) No 305/2011 regarding construction products.
Manufacturer information
Should you need any technical advice, please contact our technical support.
Contact
Poppstar GmbH
Heidelbergerstraße 49
74746 Höpfingen
Germany
Email: info@poppstar.eu
Tel: +49 (0)6283 21570-27 (Mo.- Fr. 2 PM – 5 PM)
Live chat: www.poppstar.eu (Mo.- Fr. 8 AM – 5 PM)
Misprints and changes to the product, packaging and product documentation reserved.