POPPSTAR 1010325 Cable Reel Instruction Manual

POPPSTAR 1010325 Cable Reel

SPECIFICATIONS

• Operating voltage: 250 V~ AC (max.) 50 Hz
• Maximum power when unrolled: 2500 W
• Maximum power when rolled up: 1000 W
• Cable length: consumer cable 15 m / supply cable 1.5 m
• Cable type: H05VV-F3G1.5mm²
• IP code: IP 20

SAFETY INSTRUCTIONS

Read the entire manual before setting up or using the product! Ignoring the safety instructions can lead to serious and life-threatening injuries.

• Prior to using the cable reel, check that there are no items missing and that the product is in perfect condition.
• Any installations and repairs must be carried out by a certified professional or specialist.
• Tripping risk: make sure to route the mains cable safely.
• The product has no mains switch: Only use easily accessible sockets should you need to disconnect it quickly in an emergency.
• Only connect to a properly earthed socket to reduce the risk of electric shock in case of electrical malfunction.
• Never plug the power cable in or out with wet hands.
• Plugs must match the power source, never use an adapter plug or additional extension cables.
• Always pull the mains plug out of the socket directly, never pull the cable.
• Keep the product out of reach of children.
• Never open the housing.
• Never cover the product.
• Never expose the product to extreme circumstances such as heat, cold, moisture, microwaves or mechanical pressure.
• Never crush or squeeze the cable, never pull it over sharp edges or hot surfaces and never use it to carry the product.
• Never use the cable reel in areas subject to explosion danger.
• Do not modify or disassemble the product and accessories.
• Never repair defective products yourself, please contact our technical support.
• Use the product only in dry indoors areas.

LIABILITY
Poppstar GmbH is not liable for personal injury or property damage caused by incorrect installation, use or maintenance.

PACKAGE CONTENTS

INSTALLATION

1. Choose an appropriate location near a power source with a mains switch. The cable reel must be mounted on a post, a bar or a similar stable location capable of withstanding the operating voltage.
2. Mark the position of the drill holes for mounting while using the mounting holes of the bracket.
3. Drill the holes.
4. Use mounting materials suitable for the surface (sufficiently large screws and dowels).
5. Hang the cable reel in such a way that the screw heads are placed firmly in the narrow ends of the mounting holes of the bracket.
6. Try to move the cable reel to make sure it is mounted properly.

INSTRUCTIONS FOR USE

To avoid overheating the cable, completely unroll it from the cable reel if possible.
Never pull the cable too hard or jerky as this may damage the internal connection to the cable reel.

1. The cable reel has a locking mechanism. Pull out the cable as far as you want and release gently until the cable clicks into place.
2. Connect the mains plug to a mains socket.
3. Connect the coupling socket of the cable reel to a power device.
4. Disconnect all your cables at the end of each use.
5. To automatically rewind the cable, simply pull the cable until the locking position is activated (no longer audible). Hold the end of the cable and let it rewind slowly.

ADJUSTING THE STOP-BALL

You can adjust the position of the stop-ball to keep the cable within your reach.
Steps :

1. Pull the cable out of the cable reel to the required length and lock it in place (the cable no longer rolls up).
2. Open the latch on the stop-ball and move it to the desired position.
3. Close the latch.

CAUTION : Make sure that the cable is always firmly locked before releasing the stop-ball and ensure that the stop-ball is securely locked in position before releasing the cable.

PROTECTION AGAINST OVERHEATING

A thermal protection switch is built into the cable reel. If the overheating protection is triggered (at around 63 °C), the power supply is automatically interrupted. This can occur especially under a heavy load and when the cable is not completely unrolled.
In this case, the mains plug must be disconnected so that the cable reel can cool down. After it is cooled down, press the red button (reset) and the cable reel will function properly again.

MAINTENANCE & CLEANING

• The product is maintenance-free.
• Important : Do not clean the product while it is connected to a power source. Make sure to always pull the plug out of the socket.
• Clean the cable with a damp cloth to remove dirt or dust.
• A clean, dry cloth is sufficient for cleaning the housing.
• Ensure that the cable reel is not exposed to aggressive cleaning agents or solvents.

INSTRUCTIONS FOR DISPOSAL

Product
According to the European WEEE Directive, electrical and electronic equipment must not be disposed of with regular household waste. Their components must be recycled or disposed of separately because toxic and hazardous components can cause permanent damage to health and to the environment if disposed incorrectly.
As a consumer, you are obliged under the Electrical and Electronic Equipment Act (ElektroG) to return electrical and electronic equipment free of charge at the end of its service life to the manufacturer, the outlet or the public collection points set up for this purpose. Details are regulated by the applicable national law. The symbol on the product, the instructions for use and/or the packaging indicates these regulations. By separating, recycling and disposing of old appliances in this way, you are making an important contribution to protecting our environment.

Packaging
Packaging can be disposed of free of charge at the appropriate collection points: paper in the paper bin, plastics in the plastic bin and glass in the correct glass container.

EC Declaration of Conformity
By means of the CE symbol, Poppstar GmbH declares that the product complies with the basic requirements and directives of the European regulations.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>