AENO RC1S Robot Vacuum Cleaner User Manual

AENO RC1S Robot Vacuum Cleaner

Specifications

Robot
Dimensions: Ø330mm × 330mm × 98mm. Net weight: 3.3kg. Vacuum cleaner supply voltage: 19VDC (Input), 1A, 60W. Capacity of rechargeable li-ion built-in battery: 5,200mAh. Power adapter voltage: 100-240VAC; Frequency: 50/60Hz. Dust bin capacity: 600ml. Water tank capacity: 370ml. Operating time: 62- 215min. Operating temperature: 0 °C to +40 °C. Charging time: 300-360min. The maximum height of bridged obstacles: 18mm. Controls: Manual, remote, and/or via the AENO mobile application. Docking Station Dimensions: 230 mm × 225 mm × 345 mm. Net Weight: 3.2 kg. Input: 220- 230VAC, 5A. Output: 19VDC, 1A. Rated Power: 1050W. Working Noise: about 80 dB. Suction Time: 15 sec. Dust Bag Capacity: 2.8 l. Number of cleanings before the dust bag fills up: 40. Package Contents (See Figure a) Robot vacuum cleaner

1.  docking station
2. remote control
3. power adapter
4. cleaning brush
5. dust container
6. side brushes (4 pc.)
7. HEPA filter
8. foam filter
9. mop for cleaning
10. water tank
11. batteries for the remote control
12. quick start guide, warranty card, dust bag (5 pc.)

Limitations and Warnings ATTENTION! Two UV disinfection lamps are installed at the bottom of the vacuum cleaner, between the roller brush and the battery cover (See Figure i). Ultraviolet radiation is very dangerous and may damage the eyes if you look at the lamps while operating. Never turn the vacuum cleaner upside down while it is on. Do not disassemble or repair the device on your own. Do not use the device in areas with an ignition or explosion risk, or near open flames. Use the original power adapter only, or the device may be damaged. Do not use the device outdoors. It is forbidden to load, heat, drag or bend the device, as well as stand or sit on it, or touch it with wet hands. Do not allow water to enter the device body, and do not use the device in wet areas such as bathrooms. Do not place the device in areas where it can easily fall (Tables, chairs, stairs, high platforms, etc.). Please note that bright and direct sunlight, as well as very dark surfaces, influence the operation of the infrared sensors of the vacuum cleaner. For example, dark surfaces are taken as obstacles. So, it is recommended not to leave dark carpets or fabrics on the floor, and to cover windows with curtains on a sunny day. Before operating the device, you should remove all sensitive or potentially dangerous objects from the floor such as glass, lamps, wires, curtains, valuables and jewelry, hairpins, debris, etc. The vacuum cleaner is able to bridge obstacles up to 18mm high. Please take care of children and the elderly when cleaning in order to avoid injury. If the body of the vacuum cleaner becomes too hot during charging, you should stop charging. Do not use the vacuum cleaner battery to recharge other devices. Do not close contacts or disassemble the battery. Turn off the power to the device, if it’s not operated for a long time. The device will operate on a schedule if it is always turned on and charged.

Charging Before Initial Setup

The device shall be initially charged for at least 12 hours. The following two options for charging are available:

1. Using the power adapter: Turn on the vacuum cleaner using a switch ⓮(See Figure b) and connect the power adapter ❹ to the vacuum cleaner power port ⓯. Then, plug the power adapter ❹ into the mains socket. The “Start/Stop” button will flash white, and a voice message on the start of charging will sound;
2.  Using the docking station ❷ (See Figure c): plug the docking station into a power outlet using the power plug ⓲. Align contacts at the bottom of the vacuum cleaner body ❶ (between the side brushes ❼) with the contacts on the charging station⓳. If the vacuum cleaner is correctly installed, the docking station LED ⓱ will be slowly blinking white. ATTENTION! The docking station must be installed against a wall (See Figure c). Remove all objects 1m to the left and 1m to the right of the station, as well as 2m in front of it. Device Control Using its Buttons To start operation, you should turn on the power switch ⓮ on the vacuum cleaner body (See Figure b). A voice message on the device ready for operation will sound after a few seconds. To start the vacuum cleaner, press the “Start/Stop” button on its top panel. To stop the vacuum cleaner, press the “Start/Stop” button again. After 10 minutes of inactivity, the vacuum cleaner will be switched to the Sleep Mode, and all LEDs will go off. In order to switch the device to the active mode again, press the “Start/Stop” button. After pressing the “Station” button , the vacuum cleaner returns to the docking station for recharging.

determine the end of cleaning time and will return to the charging station to recharge

| Button to start/stop the vacuum cleaner. It is also used to

confirm time  setting in  “Setting the current time” and  “Scheduled operation” modes

| Button to return the device to the docking station for

recharging

---|---
****| Button to move the vacuum cleaner forward, or change the

time in “Setting the current time” and “Scheduled operation” modes

| Button to rotate the vacuum cleaner by 180°, or change the time

in “Setting the current time” and “Scheduled operation” modes

| Button to rotate the vacuum cleaner left or right, or select hours or minutes in “Setting the current time” and “Scheduled

operation” modes

| Switching between Normal Mode and Turbo Mode of operation
| Button to switch to the “Setting the current time” mode, or

confirm the current time setting

| Button to switch to the “Scheduled operation” mode when the

vacuum cleaner starts operation daily at the set time. To reset the schedule, press and hold the “Scheduled operation” button

| Button to switch to the “Area cleaning” mode. The vacuum cleaner will mop area of 1m in diameter. In this mode, the vacuum

cleaner will operate for 30 seconds only.

Remote Control of the Vacuum Cleaner

• Tap “+” or “Add device” on the home screen of the app. In the window that opens, select the “Vacuum Cleaner”

Note : If the system prompts you to turn on some features on your smartphone, follow the recommendations in the prompts.

• Enter your Wi-Fi network name and password if the fields had not been filled automatically. Make sure that the AP mode is selected in the upper right corner.
• Press and hold the “Start/Stop” button on the control panel of the vacuum cleaner until the Wi-Fi indicator starts blinking. Then check the “Make sure the LED indicator is blinking” box on the Connection Instructions screen and tap “Next”.
• Connect your smartphone to the Wi-Fi hotspot named “Smart Life – XXXX”. Go back to the app and tap “Connect”.
• Wait for the “Device successfully added” message to

Note : The device can also be operated via voice assistants. Detailed information is available in the complete operation manual at aeno.com/documents. If the connection fails, make sure the device is plugged into a power source, turned on and charged, check the router’s Wi-Fi settings at https://aeno.com/router- help, and then repeat the connection process.

Dust Bag Replacement

Unplug the power first, then open the lid of docking station (See Figure c). Take the handle of the dust bag and pull it upwards, then throw the dust bag into the trash. Take a new dust bag from the pacakge and insert the cardboardof dust ba into the card slot on docking station, then push it to the end. Check the handle of the dust bag, make sure the handle is put to the end of the slot, and the suction port on the cardboard is open. Close the lid. Plug the power and start to use again. Make sure that the indicator flashes white slowly

Docking station indicator Status

Maintenance

You may rinse side brushes ❼ with hot water or clean them up with a damp cloth. To clean the dust container ❻, pull it out of the vacuum cleaner body by pressing the dust container lock ⓭. Then, open the container and shake out dust  and debris into the basket (See Figure h ). Open the latches and remove the pre-filter mesh from the dust container, as well as the HEPA filter ❽ and the foam filter ❾. Clean them all with a brush or a dry cloth. The water tank, the mop for cleaning and the foam filter may be washed with water. The roller brush may be cleaned after removing it from the device body by releasing the two latches.

Troubleshooting

1.  The vacuum cleaner does not turn on. Possible causes and solutions: Make sure the power switch ⓮ is turned on, and that the vacuum cleaner or the
   remote control batteries are charged, and that the distance from the remote control to the vacuum cleaner is no more than 5m. Try to start the vacuum cleaner via the AENO app. When the vacuum cleaner is on the charging station, it may not respond to commands from the remote control.

2. The vacuum cleaner does not charge. Possible causes and solutions: Make sure that the power adapter is plugged in, and that the docking station LED is flashing white. Clean any dirt from the metal contacts of both the charging station and the vacuum cleaner with a dry and soft cloth. Charge the vacuum cleaner directly from the power adapter, i.e. without the docking station.

3.  The vacuum cleaner does not connect via Wi-Fi, or the vacuum cleaner does not operate in 5GHz Network. Possible causes and solutions: Make ure your router supports 2.4GHz signal. Place the vacuum cleaner and the smartphone next to the router and try to connect again. Check if AENO app is installed. Check if the vacuum cleaner is being correctly connected to the app.

4.  The remote control does not work. Possible causes and solutions: Replace batteries. Make sure the distance between the remote control and the vacuum cleaner is no more than 5m, and that the power switch ⓮ is turned on.

5.  The vacuum cleaner does not work on schedule. Possible causes and solutions: Make sure the power switch ⓮ is turned on, and that the vacuum cleaner is charged and does not get stuck. If you restart the vacuum cleaner, the schedule will be canceled. So, set the schedule again in the AENO app.

6.  The vacuum cleaner returns to the docking station before the end of the cleaning. Possible causes and solutions: The vacuum cleaner returns to the docking station automatically when the battery level is less than 20%. Recharge the vacuum cleaner. Restart the device using the power switch ⓮.

7.  The vacuum cleaner moves back, and does not clean some areas. Possible causes and solutions: Avoid dark surfaces on the way of the device, and

Do not dispose of the device, its batteries and accumulators, or its electrical and electronic accessories together with unsorted municipal waste, as this will harm the environment. To dispose of this equipment, it must be returned to the point of sale or turned in to a local recycling facility. You should contact your local household waste disposal service for details.

What in Box

Overview

References

• Documents | AENO in Europe
• Pokyny pro pÅ™ipojení | AENO v ÄŒeské republice
• Instrukcja podÅ‚Ä…czenia | AENO w Polsce
• InstrucÈ›iuni de conectare | AENO în România
• Connecting instructions | AENO in Europe
• Инструкции по подключению | AENO
• Інструкція з підключення | AENO в Україні

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>