SMANIA 400W Professional Rotary Tool POWERSPIN Instructions

SMANIA 400W Professional Rotary Tool POWERSPIN

PACKAGE CONTENTS

• Rotary tool
• Flexible shaft
• Replacement carbon brushes (2 ×)
• Chuck key
• Transparent guard
• Accessories

TECHNICAL SPECIFICATIONS

• Chuck design: Jacobs chuck
• Chuck size: 0.6–6.5 mm
• No-load RPM: 5000–28000
• Min output power: 190 W
• Max output power: 400 W
• Rated input voltage: 230 V
• Weight: 0.9 kg
• Power cord length: 1.8 m
• 6-speed adjustment

COMPONENTS

1. Transparent guard
2. Jacobs multi-craft keyed chuck
3. Metal shield
4. Carbon brush cover
5. Speed control wheel
6. N/OFF switch
7. Adjustable heat dissipation radiator
8. Chuck key
9. Flexible shaft

HOW TO USE

ON / OFF SWITCH

NOTE: Ensure the tool has been set to the slowest speed before switching it on.
To start the tool, press the on/off switch to “I” ON position. To stop, press the switch to “O” OFF position.

SPEED ADJUSTMENT

To achieve the best result when working with different materials, you can adjust the tool speed. It is adjustable from 5000 to 28000 r/min. The tool has a variable speed control for precise speed adjustment. Set it to the required speed for operation.

NOTE: Select a low speed when working with wood, plastics and polishing. Generally, select higher speeds for small tools while lower speeds for larger tools. From number “1” to “6”, the speed corresponds from 5000 to 28000 r/min.

GRINDING/BRUSHING

Turn the tool on until full speed. Apply the tool to the workpiece gently. To obtain a good finish, move the tool in the leftward direction slowly.

NOTE: Apply light pressure on the tool. Excessive pressure will only cause a poor finish and overload the motor.

HOLDING THE TOOL

For milling or engraving, hold the tool like a pen. Take care not to cover the ventilation slots.
NOTE: The tool will get warm during normal operation.

USING THE DRILLS

The HSS twist drills are used to cut through all types of steel and steel composites.

POLISHING WITH THE FELT WHEEL

After attaching the felt wheel to the screw drill, it can be used to polish plastics, metals, steels, jewelry and small parts with polishing compounds, which will give a high luster to the surfaces of the materials. For best results, polishing accessories should be used at speeds not greater than half speed.

USING ACCESSORIES

The chart below lists the description, speed and scope of use for some of the small accessories supplied together with the tool by category. To achieve the best performance of the tool it is strongly recommended that you read it prior to operation. Failure to adhere to this may cause accessories to fail.
NOTE: ALWAYS wear eye protection. Insert the shaft FULLY into the chuck. Use ONLY up to the speeds stated below.

FITTING AN ACCESSORY

1. This tool uses the Jacobs multi-craft keyed
2. Loosen the opening of the chuck’s mouth with the included chuck key.
3. Fully insert the tool’s accessory into the chuck and tighten the chuck using the key.
4. Ensure the inserted accessory is centered and not loose.

CONNECTING THE FLEXIBLE SHAFT

WARNING : Never bend the flexible shaft with a radius of less than 152mm when operating.
Always store the flexible shaft carefully to avoid sharp bends when not in use.

1. Loosen the opening of the chuck’s mouth with the included chuck key.
2. Fully insert the inner shaft of the flexible shaft into the chuck.
3. Tighten the chuck jaws using the chuck.
4. Rotate the collet of the flexible shaft until the hole on the shaft is aligned with the hole (f) of the flexible shaft collar. Insert the locking pin to lock the inner shaft and then unscrew counter-clockwise the collet nut with a spanner.
5. Fit the accessory to the spindle socket of the flexible shaft through the collet. Keep the locking pin to lock the inner shaft and tighten the collet nut with a spanner.

WARNING! Fully tighten the collet nut before operation. Do not attempt to loosen or tighten the collet without locking the shaft, as noted above. This will result in damage to the flexible shaft.

MAINTENANCE

REPLACING THE CARBON BRUSHES
The carbon brushes must be checked on a regular basis. There are two brushes in the tool and they must be replaced in pairs. Remove the carbon brush holders with the spanner and check the brushes. If the length of the brush is less than 6mm, replace both brushes. Have the tool run at no load for 15 minutes.

NOTE : Use only the correct type of carbon brushes.
CAUTION : Using the tool with worn brushes will permanently damage the motor.

DISCLAIMER

• There are no user-serviceable parts in your power tool.
• Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth.
• Always store your power tool in a dry place.
• Keep the motor ventilation slots clean. Keep all working controls free of dust.
• Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

TROUBLESHOOTING

• If your power tool does not start, check the plugon the mains supply first.
• If your power tool is running at low efficiency,check the tool speed and type of accessory.
• If a fault can not be rectified, return the tool toan authorized dealer for repair.

WARNINGS

GENERAL SAFETY

• Keep your work area tidy and well lit.
• Do not operate a power tool in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
• Keep children and bystanders away while operating a power tool.
• Do not expose power tools to rain or wet conditions.
• Use personal protective equipment. Always wear eye protection.
• Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts.
• Keep the power tool out of the reach of children when not in use.

SAFETY NOTES

• Keep the device and its accessories away from hot surfaces.
• Persons with physical or mental impairments must not use the device and its accessories unsupervised.
• Children must not play with, clean or service the device and its accessories.
• Only use bits that fit into the power tool’s retaining system.
• Let the tool cool down after use before storing it.
• Always wait until all moving parts come to a standstill after working with the tool.

WARRANTY

The warranty is valid for 24 months. You can claim it from DFVU d.o.o., Liparjeva 6a, 1234 Mengeš, Slovenia, for a replacement product or a refund. Send us your order number and purchase date in the email, which is available by clicking on our logo in the bottom right corner. The product has a lifetime of 24 months from the date of collection.

WEEE disposal and recycling symbol. The WEEE symbol is attached to the product in compliance with the EU directive
2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). It is intended to deter the improper disposal of this product and to promote reuse and recycling.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>