Fosi Audio TB10D HiFi Digital Power Amplifier User Manual
- June 3, 2024
- Fosi Audio
Table of Contents
TB10D HiFi Digital Power Amplifier
User Manual
Product Specifications
Fosi Audio TB10D is a Hi-Fi stereo 2-channel amplifier that features 300W x 2 output, it is a mini power amp that is equipped with bass and treble control. Simple compact design but practical and powerful! Home Hi-Fi integrated amplifier designed for customers who pursue Hi-Fi sound!
| Audio Input: | RCA Input |
|---|---|
| Power supply: | 32V5A |
| Power supply voltage range: | 18V-48V |
| THD: | <0.3% |
| SNR: | 2 90dB |
| Frequency Range: | 20Hz – 40kHz (±1 dB) |
| Input Sensitivity: | < 600mV |
| Terminating Impedance: | 2Ω-8Ω |
| Output Power: | 300W + 300W |
| Product Size: | 166 x 105 x 40 mm |
| Product Weight: | 650g |
Product Overview & Control Functions
Package Contents
Fosi Audio TB1 OD Amplifier 1
AC Power Cord1
32V Power Supply 1
User Manual 1
Quick Setup
Preparation
Prepare 1: TB10D, 32V power supply, passive speakers, speaker wires, or
banana plugs;
Prepare 2: Connect the TB10D to the passive speakers via the speaker wire
or banana plugs;
Prepare 3: Connect the 32V power supply to the DC input;
Prepare 4: Toggle the power switch on the front panel upwards to turn on
the TB10D amplifier.
Note: Be sure that the volume/power switch is in the OFF position before
connecting the power supply.
How to connect the speaker wire?
Method 1 : Bare wire connection illustration
- : Release the horn terminals block terminals;
- : Insert the two ends of the speaker wire into the amplifier and speaker terminal holes;
- : Tighten the horn terminals;
Note: Please avoid the speaker wires being exposed and touching the amplifier casing, as this may cause a short circuit fault.
Method2: Banana plugs connection illustration
- : Release the banana jacket;
- : Loosen the screw;
- : Insertion speaker wire and tighten the screw;
- : Tighten the banana jacket;
- : Insert the banana plug into the horn terminals of the speaker and amplifier.
Note: Please take care to avoid contact between the two banana plugs and cause a short circuit fault as some of the banana plugs are metal cased.
Follow RCA Input Steps:
Prepare: audio source (take a phone as an example), an RCA cable, or a
3.5mm AUX to RCA cable (some devices will need it).
Step 1: Connect your phone to TB1 OD via a 3.5mm to RCA cable;
Step 2: After a successful connection to TB10D, The input mode indicator
light will turn red;
Step 3: Open the audio application, play, and enjoy!
Note: Please keep the TB10D away from another electric device. The TB10D
can’t use with a radio simultaneously.
Troubleshooting/QA
1: What type of speakers work best with TB1 OD Amplifier?****
– TB10D works great with any 2-8 Q passive speakers.
Note: please know that the TB10D amplifier is for passive speakers, not for
powered speakers and subwoofers.
2: Why does the TB1 OD make serious noise when used together with a radio?****
– A common feature of Class D power amplifiers is that they can cause serious noise when used with a radio, so we do not recommend using the TB10D with a radio or too close to it.
3: Can I connect a turntable to the TB1 OD amp, why is the volume extremely Low?****
– As the turntables do not have a built-in preamp, you need to add an external
phono preamp before connecting TB10D.
– As for the turntables which have a built-in preamp, you need to switch the
preamp on before connecting TB10D.
4: Why does my power indicator not light up?****
– Please check that the AC power cord is securely connected to the power
supply and to an AC power outlet.
– Please check that the AC power outlet is supplying power, make sure the
power LED on the power supply will stay on.
– Please replace another power supply and try it again. 18-48V DC power
supplies are suitable.
– If you make sure the power supply is defective, please contact us for an
exchange.
5: Why does the sound is cracking or make a lot of electric noise?****
– Please make sure all the cables are completely pushed into the devices, the
incomplete connection will cause this cracking.
– Please remove all the inputs and then check whether the cracking noise
disappears or not, the cracking may be from the audio source or input cables.
– If you are not using the original factory standard power supply, please
replace the power supply before testing. Many power supplies in the market
have large interference coefficients, which will cause a lot of current
sounds.
6: Can I use headphones with this product?****
– No, the TB10D cannot be connected to headphones and only supports passive speakers.
7: Why there is no voice from my amplifier?****
– Please check whether the cable of the power supply is connected to TB10D and
whether the power indicator is on.
– Make sure the TB10D indicator light is on when the power is turned on.
– Please check that the TB10D and your source components are turned on and not
set to minimum volume, if possible replace your source and test again.
– Check that the wire connections from the audio source to each speaker in the
amplifier are connected correctly.
– Please check that the cable is not loose, or damaged. An incomplete
connection is one of the main reasons for no sound.
8: How much power does this use in standby mode? Can this amp be left on all the time?****
– This is the class D amplifier, it will cost very low power when it is in standby mode. It can be connected all the time and it is safe without power consumption.
9: Sound quality is not good?****
– Make sure all the cables are fully connected.
– Adjust the treble and bass control of the power amplifier to achieve the
right tone.
– Please try to change the sound source and cables to test.
10: Should I unplug the power cord?****
– If the item will not be used for a long time, please unplug the power plug to prevent the item from being burnt due to a lightning strike.
11: Can I bridge channel 1 and channel 2 to get 600watts?****
– NO, this amplifier can’t be bridged.
12: How can I connect TB10D to the TV?****
– Because the TB10D has an RCA input, it can be connected to a TV.
13: Will I be able to turn up the volume using my TV controller or will I need to adjust the volume manually?****
– Technically speaking the TV’s remote control does not control the volume of the amplifier and adjusting the volume of the amplifier requires the manual use of the amplifier’s volume control buttons, but the size of the signal from the TV to the amplifier will affect the sound output of the amplifier.
14: Why the sound cut in and cut out?****
– Try to reduce the sound of the sound source.
– Try to change the audio source to test.
– Reduce the volume of the treble and bass knob on the TB10D.
– Ensure that the positive and negative poles of the speaker output do not
touch together. Some relatively large banana plugs are easy to touch together
and cause a short circuit.
15: Can I Connect a Subwoofer to the Fosi Audio Amps?****
– If you bought subwoofer amps from Fosi Audio or a 2.1 channel amplifier(the amp that with sub output), you can connect to a subwoofer, but if you got the 2.0 channel amp, you can’t connect to the subwoofer.
16: Can I exchange the power supply that comes with the amplifier to get more power?****
– The TB10D comes with a 32V 5A power supply, it’s enough for most bookshelf speakers, but if you want to get more power, you can exchange the power supply, the voltage range is DC18-48V, you can use 24V SA or 32V 6A power supply.
17: Can I take the TB10D to other countries?****
– Yes, the wide voltage AC 110-240V for power input can be used in any country. You only need to match the power cord adapter of the corresponding country.
Any problems please leave a message to the customer support email address: support@fosiaudio.com
Comparison Section
| Model | TB10D | TB10A | TDA7498E | V1.0G |
|---|---|---|---|---|
| Picture | | | |
Type| 2.0 CH Amp| 2.0 CH Amp| 2.0 CH Amp| 2.0 CH Amp
Input| RCA| RCA| RCA| RCA
Output| Passive Speakers| Passive Speakers| Passive Speakers| Passive Speakers
Power Adapter| 32V/5A| 24V/4.5A| 24V/4.5A| 19V/4.74A
MAX Power Output| 300 watts x2| 100 watts x2| 160 watts x2| 50 watts x2
Warranty Information
- All Fosi Audio products have an 18-month limited warranty on parts and labor from the date of purchase. Please contact us if you have any problems.
About Fosi Audio
- Fosi Audio designs and builds innovative audio products with all your music in mind. Great sound, simple but elegant designs, high-quality materials, and truly useful features are what Fosi Audio is about. We sincerely hope you get as much enjoyment from our products as we’ve had to create them!
Our website:www.fosiaudio.com
Amazon store:www.amazon.com/fosiaudio
Our Youtube channel: Fosi Audio
Our Facebook page: Fosi Audio
After-sale Service and Technical Support Email:
support@fosiaudio.com
fosiaudio@hotmail.com
https://h5.shengcai.net/wwei/url?url=H666G_V7w6G
Fosi Audio Product’s User Manual
Documents / Resources
| Fosi
Audio TB10D HiFi Digital Power
Amplifier
[pdf] User Manual
TB10D, HiFi Digital Power Amplifier, Power Amplifier, HiFi Digital Amplifier,
Digital Amplifier, Amplifier
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>