MONSTER PUSAT K3 Pro Mechanical Gaming Keyboard User Manual

: June 5, 2024
: Monster

Table of Contents

FAQ
Function Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MONSTER PUSAT K3 Pro Mechanical Gaming Keyboard User Manual

Dear User

Thank you for choosing Pusat brand. To Protect your rights and for better costumer service, we ask you note our warranty rules.

Within 24 months from purchase date, repair guarranteed for failure due to electrical circuit problems. Man-Made damages, such as disassembly, hard impacts, submersion into water, plugging into improper current or voltage, and damage caused by natural disasters such as fire, flood or earthquake are not included.
Consumable part (such as foot stick) and spare parts replacement, are not included in our warranty.

O. S. Support
Windows XP/Vista/7/8/10

FAQ

If the keyboard doesn’t respond, please check if the keyboards USB cable is Correctly inserted into the corresponding USB port on the computer, or try another USB port on the computer.
If you spill liquid on the keyboard, please remove keyboards USB cable from the computer immediately. Wipe up excess liquid and put the keyboard in a warm place (for instance, under a lamp) to let the keyboard dry naturally before using again.

Function Instructions

Computer USB port interfaces with the keyboard without needing to install drivers or software.
Multi-level backlight brightness: Press and hold the [FN] key, and then press the arrow key “↑”to increase the backlight brightness of the keyboard. Press and hold the [FN] key, and then press the arrow key “↓”key to decrease the backlight brightness of the keyboard.
Adjustable lighting direction: When backlit keys are cycling through effects press FN + [←]to change directions. Adjustable colors: Press FN+[→] to change backlight colors.
Adjustable lighting effect speed: Press and hold the [FN] key, and then press the + key “+” to increase the speed of the lighting effect. Press and hold the [FN] key, and then press the – key “-” to decrease the speed of the lighting effect. There are 6 levels of adjustment.
There are 18 backlighting effects:
<1>FN + INS = A. Trial B. Briefing C. Static <2>FN + Home = A. Ripple Graff B. Pass without Trace C. Coastal <3>FN + PGUP= A. Hurricane B. Accumulate C. Digital Times <4>FN + DEL= A. Go with Stream B. Clouds Fly C. Winding Paths <5>FN + END = A. Flower blooming B. Snow Winter Jasmine C. Swift action <6>FN + PGDN = A. Both ways B. Surmount C. Fast and Furious
Adjustable side LED lighting effect mode: Press and hold the [FN] key, and then press the PAUSE key “PAUSE” to change the effect mode. There are Wave, spectrum, breathing, constant light and off mode (LED light can be customized, and the LED light on the board and side LED could be synchronized).
Adjustable side LED lighting speed mode: Press and hold the [FN] key, and then press the SCRLK key “SCRLK” to change the speed. There are 5 different level of the adjustment.
To disable the [WIN] key: Press and hold the [FN] key, and then press left [WIN] key to turn off [WIN] key in order to avoid leaving gaming function if user presses [WIN] key by mistake. Repeat the above operation to restore the function.
[Volume Scroller Key Control] Press to switch between Brightness and Volume adjust modes. Light On – To adjust the brightness of the keyboard backlit. Light Off – To adjust the Volume of the system. 10. [Macro Keys, G1 ~ G5] G1 ~ G5 default set as F1 ~ F5. When the “G” key has macro content, the button light will be on; when there is no content the light will be off and perform as the default button function F1~F5.
[Macro Record Function “REC”] Press the “REC” button to be solid light to start the recording function, the NUM, CAP, SCR, WIN indicators will flash slowly, then select G1 ~ G5 to flash rapidly to be the corresponding button to be stored. Press the valid button to start recording, the maximum will be 64 normal buttons or within 30s. The recording will be automatically exit and save or press the REC button after the recording is completed.
[Erase Macro Function] Press the “FN” + “REC” and hold for 5 seconds to erase all the Macro settings. Erase specific Macro key: Press the “REC” button to be solid light to start the recording function, the NUM, CAP, SCR, WIN indicators will flash slowly, then select G1 ~ G5 to flash rapidly to be the corresponding button to be erased. Press “REC” key button to complete the erase process. After the Macro has been erased, it will go back to default setting as F1 ~ F5.
[LED Memory Keys, M1] Press M1 to light up the LED of W /A /S /D /↑ /↓ /← /→ keys (default: RED color) with stored setting.
[LED Memory Keys, M2] Press M2 to light up the LED of ESC/ TAB/ SHIFT_L/ CTRL_L/ 1/ 2/ 3/ 4/ 5/ Q/ W/ E/ R/ A/ S/ D/ F/ G /SPACE keys with stored setting.
[LED Memory Keys, M3] Press M3 to light up the LED of ESC/ `/ 1/ 2/ 3/ 4/ TAB/ Q/ W/ E/ P/ A/ S/ D/ F/ G/ V/ B/ CTRL_L/ SPACE keys with stored setting.
[LED Memory Keys, M4] Press M4 to light up the LED of ESC/ 1/ 2/ 3/ 4/ 5/ 6/ TAB/ W/ A/ S/ D/ F/ L/ Z/ X/ C/ V/ CTRL_L/ SPACE keys with stored setting.
[LED Macro Record Key, MR] Press the “MR” key once to start the LED Macro Record mode. The NUM, CAP, SCR, and WIN indicators will flash slowly. Then select M1 ~ M4 to specify the recording key. The corresponding button will flash rapidly to start to record. Press the valid button on the keyboard to record the light setting and within 30s it will automatically exit and save the setting. Or press the “MR” key after recording is comp leted to exit and save the setting.
[Erase LED Macro Setting] Press the “FN” + “MR” and hold for 5 seconds to erase all the LED Macro settings. Erase specific LED Macro key: Press the “REC” button to be solid light to start the recording function, the NUM, CAP, SCR, WIN indicators will flash slowly, then select M1 ~ M4 to flash rapidly to be the corresponding button to be erased. Press “MR” key to complete the erase process.
[Default Setting] Press the “FN” + “PRTSC” to reset the setting to default.