WAVLINK WN0006 WiFi 6E Tri Band AX5400 PCI-E Adapter User Manual
- June 16, 2024
- WavLink
Table of Contents
QUICK START GUIDE
WiFi 6E Tri-Band AX5400 PCI-E Adapter
WN0006 WiFi 6E Tri Band AX5400 PCI-E Adapter
www.wavlink.com/en_us/WS-WN675X3
Scan the QR code or load the link for Quick Start Guide and Driver downloading
WS-WN675X3
****WAVLINK (@WavlinkOfficial)
WAVLINK SUPPORT (@WavlinkTechSupport)
Introduction
Wavlink Tri-Band PCFE is an AX5400 wireless adapter for desktops that supports the latest Bluetooth 5.3. The wireless adapter features stable signal, high speed rate and superior performance. Compliant with 802.11 ax specification,the wireless adapter supports 2.4G, 5G and 6G bands. With 1024-QAM and MU-MIMO technology, WL-WN675X3 delivers wireless signal faster and more effective by cooperating with an MU-MIMO compatible router.
In the box
– | x WiFi 6E Tri-Band AX5400 PCI-E Adapter
– | x Bluetooth Cable
– 2 x External Antennas
– | x Baffle
– 1 x Quick Start Guide
Several Screws
System requirements
– Microsoft Windows 10/11 64 bit or later
Installation
- Unplug your PC and remove the case panel.
- Connect the Bluetooth cable to the adapter.
- Find the corresponding PCI-E slot, then inset the adapter carefully.
- Find an available F_USB slot then carefully connect the adapter to it.
- Mount the external antenna to the adapter base.
- At last install back the PC case panel then you can get ready to install the driver.
Driver setup
After installation, please visit the following website to download the latest
driver for PCI-E adapter.
www.wavlink.com > SUPPORT > Driver > Wireless > Pcle
Wireless > Adapter
- Unzip the file then you’ll see two files, BT-xxx-Win10-Win11.exe is for Bluetooth and the other WiFi-xxx-Win10-Win11.exe is for Windows. Please double-click the one for windows.
- Then installer requires you to click “Next” for further setup.
- Now please agree to the license terms and conditions, and click“Install”.
- Please wait patiently for the installer to complete the setup process,click “Finish” after completing the installation.
FCC STATEMENT
-
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Prohibited for control of or communications with unmanned aircraft systems.