MONSTER QSMX1 Airmars X1 Wireless Gaming Mouse User Manual
- May 15, 2024
- Monster
Table of Contents
Monster Airmars X1
Wireless gaming mouse
user’s manual
Product Parameter
- Number of buttons————————————————· 6
- Transmission distance——————————————· 10M
- DPI—————————–· 800/1600/2400/4800/6400/8000
- Mode———————————————- 2.4G+BT+Wired
- Button life ———————————————– 8 million times
- Lighting——————————————————— RGB
Packing List
Kindly reminder
- Do not attempt to disassemble or replace any parts of the product except for those operations specifically indicated in the instruction manual.
- Do not put the product into water or any other liquid, this product is not waterproof design.
- If any liquid accidentally enters the product, please disconnect and remove the product immediately.
- To avoid electric shock, please make sure there is no water on your hands when installing or uninstalling the product.
- Do not place this product near a heat source or expose it directly to a fire source.
- Do not place this product in an environment with strong electromagnetic force, as this may cause the product to malfunction.
Product Introduction
Mouse Size: 121.09 x 71.6 x 40.2mm
Product Introduction
Charging base Size: 76 x 40.29 x 48.82mm
Mouse Dock Charging Instructions
The charging dock cable connects to the charging head, followed by placing the mouse on the dock for charging.
System Support
The mouse supports pairing with computers with Windows OS 8 and above, Mac OS 10.10 and above and Google Chrome OS installed.
Connection mode
-
Wired mode：
1. Connect the Type-C cable to the mouse and the USB cable to the computer, the computer will automatically recognise and configure the mouse;
2. After the configuration is complete, the mouse is ready to use.
3. Plug in the USB cable to automatically switch to wired mode. -
2.4G mode：
1. Remove the mouse cover, take out the 2.4G receiver, and switch the mouse mode switch up to 2.4G mode.
2. Insert the receiver into the computer, it can be used normally at this time. -
2.4G Strong pairing mode：
Press the left, center and right buttons at the same time for 3-5 seconds, the DPI light flashes yellow rapidly, at this time, plug the receiver in, LOGO light cycles normally indicating a successful connection. -
Bluetooth mode：
1. Switch the mouse mode switch down to Bluetooth mode, at this time the DPI indicator light flashes blue rapidly, indicating that the mouse enters the Bluetooth pairing state.
2. Open Bluetooth on the computer and connect the Bluetooth device “Airmars X1”, LOGO light normal cycle that has been successfully connected. -
Bluetooth strong pairing mode：
Press the left, center and right buttons at the same time for 3-5 seconds, the DPI indicator will flash blue rapidly, then search for “Airmars X1” and connect it, the LOGO light will cycle normally after successful connection.
Middle Button Indicator Description
| Low Voltage Indication | Red light flashing |
|---|---|
| Mouse charging | Red light always on |
| Mouse fully charged | Green light always on |
• Mouse Eight Effect：
Mouse configuration 8 kinds of lighting effects
[1. Colorful Streaming (default)] [2. Color Changing Breathing] [3.Monochrome
Always Bright] [4. Neon] [5. Drag Tail] [6. Colorful Always Bright] [7.
Colorful Jumping] [8. Turn Off Lights]
DPI Function Description
6 DPI level indicators
Press the DPI cycle button to switch the mouse DPI level;
800 Red, 1600 Blue, 2400 Green, 4800 Pink, 6400 Yellow, 8000 Cyan.
| Name of the Parts | Hazardous Substances |
|---|---|
| Pb | Hg |
| Housing | O |
| PCBA | X |
| Accessories | X |
This table is compiled according to SJ/T 11364.
O: Indicates that this hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in GB/T 26572
X: Indicates that this hazardous subatance contained in at least one of the
homogeneous materials used for this part is the limit requirement in GB/T
26572.
Environment Friendly Use Period (EFUP)
This logo refers to the period (10 years) during which the hazardous
substances in electronic and electrical products will not Leaker mutate so
that the use of these [substances] will not result in any severe environmental
pollution, any bodily injury or damage to any assets.
Warranty Card
Dear user, this warranty card is your certificate for applying for warranty in the future, please cooperate with the seller to fill it out and keep it in a safe place for future use!
User Information
Username| | E-mail|
Contact Number| | Postal code|
Mailing Address|
Product Information
Product Name| | Product number|
Product barcode/number/lot number|
Vendor Information
Name|
Address|
Contact Number| | Postal code|
Sale Date| | Invoice number|
Remark|
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee thatinterference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment
complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum
distance 0cm between the radiator and your body.