Poemoon P40-600C1 24 Inch Modern Pendant Light User Guide

Poe moon P40-600C1 24 Inch Modern Pendant Light User Guide

INSTALLATION INSTRUCTION

WARNING : TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR REMOVE THIS FIXTURE.

NOTE: Please carefully check all the mounting accessories are complete before installation, if you are missing any accessories, please feel free to contact us through email.

Before getting started, ensure the package contains the following components:

Short Mounting Screws *2
| 4
a3| | 4
a4| (Already installed on the Canopy)
| 1
a5| | 3
a6| | 4
a7| | 4

Tools required

Electrical test reminder :

• Test the electricity of the light fixture first before installing, and if it can be properly functioning please follow the steps 1-3 as below to install.
• Any questions about the installation process, please contact the email address at the bottom of the first page, prompt response will be offered within 24 hours.

Installation Steps

Step 1 ( Install the mounting bracket )

WARNING : Please keep turning off the power source while removing or installing the light fixture.

a. Unscrew the fixture screws(al) from the canopy(A).then take out the mounting bracket(a4) from the canopy(A).
b. Pull out all wires from the outlet box, then match the holes on the mounting bracket(a4) with the outlet box.
c. Install the mounting screws(a2) and washer(a3) through the preset holes toward the outlet box.

Step 2 (Connecting wires )

NOTE : If you have electrical questions, consult your local electrical code for approved grounding methods.

a. Connect the indoor live wire with the black wire(L) of the light fixture by twisting two wires together, then use the wire nut(a2) to twist them together.
b. Connect the indoor natural wire with the white wire(N) of the light fixture by twisting two wires together, then. use the wire nut(a2) to twist them together.
c. Then install the green screws to the mounting bracket, please see the picquet 2a.
d. Connect the indoor ground wire with the ground wire of the light fixture by twisting two wires together, then use the wire nut(a2) to twist them together.

ATTENTION: Please make sure to wrap the cooper ground wire of light fixture around the green screw before you connect two wires together, make sure the cooper wire stay on the mounting bracket.
e. Use the wire tape to tie all the wires for a secure connection, then put all the connected wires into the outlet box.
f. Use the canopy (A) to cover the outlet box and fix the canopy(A) with the Fixture Screws (al) as the picture 2b.

Step 3 (Installation of Crystal Prisms)

a. As picture 3a shows, There are 2 rings of crystal prisms that need to be installed.
b. Place the crystal strip vertically into the hole cl of the lamp body from above.
Suggested to install the crystal prisms in order bilateral symmetry, and then install it from bottom to top. (Priority installation of Inner ring crystal prisms(D).
c. Turn on the power supply.
d. Turn on the light switch.

Trouble shooting

WARNING: Make sure the power is off at the electrical panel box before you attempt any repairs. If any problems or dissatisfaction during using, please contacts: E-mail: banleris@163.com

Test or replace the switch.
Check the wiring.
Replace the light bulb.
The fuse blows or the circuit breaker trips when the light is turned on| Check the wire connection.

Care and Cleaning

• Disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box.
• Use a dry or slightly dampened clean cloth to wipe the interior surface of the fixture.

USE AND CARE GUIDE

Retain this manual for future use

If you have any problems or dissatisfaction, Please feel free to contact E-mail:banleris@163.com.Your satisfaction has always been the goal we are chasing

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>