coccolle 322086520 Lyra Car Seat User Manual

June 5, 2024
coccolle

coccolle-322086520-Lyra-Car-Seat-LOGO

coccolle 322086520 Lyra Car Seat

coccolle-322086520-Lyra-Car-Seat-
PRO

Instructions

Please read the instructions before using the child car seat. The instructions should be kept properly for future reference. A violation of the instructions may endanger the safety of children to varying degrees. Do not place child safety seats on front car seats equipped with safety airbag, which may cause serious injury or even death to children.
Group 0+
This is an Isofix child car seat. It is approved to Regulation No.44 ,04 series of amendments for general use in vehicles fitted with ISOFIX anchorages systems. It will fit vehicles with positions approved as ISOFIX positions (as detailed in the vehicle handbook), depending on the category of the child car seat and of the fixture.The mass group and the ISOFIX size class for which this device is intended is:0+,D
Group 0+, I, II, III
This is a “Universal”child carseat . It is approved to Regulation NO.44,04 series of amendments , for general use in vehicles and it will fit most , but not all , car seats. A correct fit is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehicle is capable of accepting a “Universal” car seat for this age group. This car seat has been classified as “Universal” under more stringent conditions than those which applied to earlier designs which do not carry this notice. Only suitable if the approved vehicles are fitted with 3 point safety-belts , approved to UN/ECE Regulation No. 16 or other equivalent standards. If in doubt , consult the manufacturer or the retailer.

Parts list

  1. 3 point safety-belts piercing
  2. Shoulder strap sleeve
  3. Crotch pad (pulling buckle sleeve)
  4. Angle adjusting handle
  5. Headrest
  6. Backrest
  7. Shoulder strap piercing
  8. Shoulder straps
  9. Mattress
  10. Pulling-buckle
  11. Adjuster cover
  12. Shoulder strap adjusting belt
  13. Base
  14. Rotary adjusting button
  15. Headrest adjusting handle
  16. Top tether
  17. Connective band of strap sleeve
  18. Shoulder straps
  19. Shoulder straps adjusting belt
  20. Isofix chunk coccolle-322086520-Lyra-Car-Seat-FIG1 coccolle-322086520-Lyra-Car-Seat-FIG2

Characteristics

  1. This product uses 3-point car seat belt and ISOFIX chuck to install on the car.
  2. The headrest can be adjusted, the body can be rotated 360 degrees, and can be adjusted in many angles, convenient for children to sit straight or lie down.
  3. This product is designed for children weighing in 0-36Kg.

Safety instructions

For the safety of your child, please read the following instructions carefully. Carelessness or mishandling can lead to many injuries.

  1. This product can be used for children with body weighing in 0-13kg (Group 0+ ). It uses 3- point seat belt or ISOFIX and top tether rearward mounted in the car, use 5 point harness system to fix the child. It is forbidden to carry more than one child or overload. Make sure all the belts are not twisted.

  2. This product can be used for children with body weighing in 9-18kg (Group I). It uses 3-point seat belt forward install in the car, use 5 point harness system to fix the child. It is forbidden to carry more than one child or overload. Make sure all the belts are not twisted.

  3. This product can be used for children with body weighing in 15-36kg (Group I II).
    Move 5 point harness system, use 3 point seat forward install in the car. Or use isofix and 3 point seat forward install in the car. Or use isofix and 3 point seat belt forward install in the car. It is forbidden to carry more than one child or overload. Make sure all the belts are not twisted. 3).Only suitable if the approved vehicles are fitted with3 point safety-belts, approved to UN/ECE Regulation No. 16 or other equivalent standards.

  4. For an ISOFIX child car seat, the instruction for use shall be given to read the car manufacturer’s handbook.

  5. Any straps holding the car seat to the vehicle should be tihght , that any straps restraining the child should be adjusted to the child’s body , and that straps should not be twisted.

  6. Ensure that any lap strap is worn low down, so that the pelvisis is firmly engaged.

  7. The product should be changed when it has been subject to violent stresses in an accident. Any alterations or additions to the device without the approval of the Type Approval Authority, and a danger of not following closely the installation instructions provided by the child restraint manufacturer.

  8. If the product surface cloth is not textile, put away from sunlight, otherwise the surface will burn children’s skin.

  9. This product is not designed for domestic use and can only be used in cars. For safety reasons, even if the child is not in the seat, this product should only be installed in the car. It is forbidden to leave children alone in their car seat unattended.

  10. Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured. Make sure that they do not cause harm to children in the event of a vehicle collision.

  11. The child car seat shall not be used without the cover. And the seat cover should not be replaced with any other than the one recommended by the manufacturer, because the cover constitutes an integral part of the car seat performance.

  12. The instructions of this product can be kept in the reserved place of the child seat during the life span of the product.

  13. Warning: the installation path of the seat belt can not use any other force point except the mark. If there is any doubt, please contact the safety manufacturer. coccolle-322086520-Lyra-Car-Seat-FIG3coccolle-322086520-Lyra-Car-Seat-FIG10

Usage method

  1. The mounting position of the seat in a vehicle
    This car seat is available with a three-point seat belt that passes throughor UN/ECE Regulation 16 or other equivalent standards. Not suitable for models with only 2-point seat belts.
    Note: it is recommended that the ISOFIX chuck of the seat be locked on the ISOFIX connector of the car when installing the child seat. Can improve seat safety and comfort. coccolle-322086520-Lyra-Car-Seat-
FIG13

  2. Check the height of the straps
    Check that the height of the shoulder harness is suitable for the child: the harness must be equal to the child’s shoulder or slightly larger than the shoulder position of the child (fig. 3). The height of the shoulder strap can be adjusted up and down with the height of the head restraint. When using the car seat, adjust the height of the head restraint to adjust the height of the shoulder strap. coccolle-322086520-Lyra-Car-Seat-FIG4

  3. Buckle using
    Step 1- pull the button left and right together
    Step 2- insert the closed insert into the slot at the same time. If you hear the click sound it means that the buckle is stuck. Pull the insert up and check that the buckle is locked properly. Step 3- to unfasten the seat belt, press the red button down and the insert will pop up automatically. coccolle-322086520-Lyra-Car-Seat-FIG19

  4. Adjust the length of the strap
    Step 1 – Drag the left and right buttons together
    Step 2 – Insert the buckles into the slot at the same time. If you hear the “click” sound, it means it is locked.
    Step 3 – To open the belt, press the red button down and the buckles will jump automatically. coccolle-322086520-Lyra-Car-Seat-FIG14

  5. Pull the straps out until they are fully tightened. Strain the straps as much as possible without causing the child’s discomfort. The safety belt should be as low as possible and should be placed near the legs and not the abdomen. Free belts are dangerous. Therefore, every time the child is seated on the car seat, check that the seat belt adjustment device can be used normally, then pull the straps, tighten the straps and do not twist (figure 1).

  6. The shoulder strap can be weakened by pressing the seat belt adjustment device hidden under the seat of the car seat. Operate the seat belt adjustment device while holding the two front straps with the other hand to loosen the straps (fig. 2).

  7. Adjust ISOFIX chuck
    Press the red ISOFIX release button and push the fit chuck out to the outermost so that the ISOFIX chuck can be installed. If you want to retract the ISOFIX chuck you can pull the ISOFIX chuck back by pressing the red ISOFIX release button inward. coccolle-322086520-Lyra-Car-Seat-FIG5

  8. Car seat installation
    Step 1 – First pull the ISOFIX connector to the outer end, then insert it into the car. When you hear the click sound, the Isofix connectors are connected. At this time, the green color will appear on the lock display window.
    Step 2 – push the car seat behind the car until the two are perfectly aligned. If you want to release the ISOFIX connectors, you can release the ISOFIX connectors by pressing the red release button.
    Step 3 – Use a 3-point seat belt to connect the seat.coccolle-322086520
-Lyra-Car-Seat-FIG11

  9. Adjusting the seat angle
    The angle of the seat can be adjusted by pressing the red key. Adjust the angle of the car seat to the right position for your child to enhance the comfort required. (Figure 1, Figure 2).  coccolle-322086520-Lyra-Car-Seat-
FIG12

  10. Adjusting the car seat rotation
    The car seat can be rotated 360 degrees by pressing the red rotary knob down. It is convenient to adjust the correct direction of use. coccolle-322086520
-Lyra-Car-Seat-FIG9

5. Installation and use of the car seat

  1. Installation of the car seat (group 0+: 0-13 kg) Use baby insert cushion and reducer to imporve comfort.
    This product is suitable for children weighing between 0-13 kg when used rear- facing. Installation method 1:
    Step 1 – Pass the top tether belt through de belt guiding as the images show. Then install the top tether clutch in the relevant place on the automobile as the car’s manual indicates. Once the display of the top tether goes green it means that the top tether has been properly fitted and installed. Adjust the length of the top tether by loosening the belts fom the Yoke connector located on the rear side of the car seat.
    Step 2 – Use the Isofix to fix the car seat in the car. Ensure that the green color appears on the window and then gently push in the Isofix connectors of the machine until it snaps into place.
    Step 3 – As shown in FIG. 1, pull the top tether though the two sides of car seat backrest, hang the anchor to the attachment p. oint on your car (suggested attachment point in your car manual). As shown in FIG. 2, pull it as tightly as possible. The top tether indicator will turn green until it is locked.
    Installation method 2:
    Step 1 – Adjust the seat to the most inclined position.
    Step 2 – As show in FIG. 1 and 2, through the three-point seat belt through the belt guide of child car seat, tighten the seat belt and secure the child car seat on the car seat.

  2. Group ( 9-18 kg ) Remove baby insert cushion.
    This product is suitable for children weighing between 19-18kg forward-facing.
    Step 1 – Use the three-point seat belt, as shown in fig. 1, tighten the seat belt and secure the child seat on the car seat. Then place the reducer to improve comfort.
    Step 2 – Place the child in the car seat 2.4, 3.4, 4.4, 5. Check the shoulder strap and the height of the head restraint. Make sure all the belts are not twisted.

  3. Group (II III – 15-36 kg) Remove baby insert cushion and reducer.
    This product is suitable for children weighing between 15-36kg forward facing.
    (Check 5.4 to remove seatbelt and buckle)
    Installation method 1:
    Step 1: First adjust the seat to the highest position and put it in the car.
    Step 2: Place your baby in the car seat and fasten the car seat with a three-point seat belt. Make sure all the belts are not twisted.
    Installation method 2:
    Step 1 : First adjust the seat to the highest position and put it in the car
    Step 2: Use the Isofix to secure the car seat in the car. Ensure that the green color appears on the window and then gently push in the Isofix connectors of the machine until it snaps into the place.
    Step 3: Place your baby in the car seat and fasten the car seat with a three-point seat belt. Make sure all the belts are not twisted.

  4. Removing safety belt and buckle
    Step 1 – Remove the straps as shown in fig. 1.
    Step 2 – Lower the buckle and remove the reducer and shoulder straps with shoulder straps under the sleeve. Remove the iron from the base of the sun and remove it from the buckle.

Maintenance and cleaning

  1. Routine maintenance
  2. During daily use, the child seat should be checked. In the event of an accident, the seat must be replaced.
  3. When not using the child seat, place it in a dry and ventilated place to avoid moisture and mold.
  4. If the dust is on the child seat, clean the seat belt and plastic parts with a damp sponge and then dry with ventilation.
  5. If you get rid of food or drink on the seat belt, remove it and rinse it with warm water, then dry with ventilation.
  6. If you want to clean the cover, check 6.2
  7. Washing care instruction
    Solvents, chemical cleaners and lubricants are prohibited for any parts of this product.

Main technical parameters

  • Distance between front and rear: 500 mm,
  • Distance between left and right: 500 mm,
  • Height: 596 mm,
  • Weight: 7kg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals