coccolle Atira Car Seat 0-36 Kgs Isofix Cinnamon Brown Instruction Manual

coccolle Atira Car Seat 0-36 Kgs Isofix Cinnamon Brown Instruction Manual

coccolle Atira Car Seat 0-36 Kgs Isofix Cinnamon Brown

Coccolle Atira car seat – Group 0/1/2/3, 0-36 kg 1.NOTICE

1. Please read the manual carefully, because an incorrect installation may cause serious injury, in which case the manufacturer does not take any
2. Scope of use: the child safety seat is suitable for children weighing from 0 kg, from birth to 36 kg (Gr. 0+/1/2/3, from birth to about 12 years old children.)

3. It is certified that this seat complies with ECE 44/04 regulations and can be installed on most
4. Precautions for use: for your child’s safety, please read the instructions Carelessness or improper operation can lead to many avoidable injuries.
   • This product can be used for children weighing up to18kg (group 0+, group I, approximately 4 years old), using the five-point safety belt of the child safety
   • This product can also be used for children weighing 15-36kg (group II, approximately 3-6 years old; group III, approximately 6-12 years old), without using the five-point safety belt of the child safety seat, but using the car seat’s three-point safety belt on the car seat is fixed.
   • Each safety belt connected to the child safety seat should be fastened The safety belts restraining the child should be adjusted according to the child’s body. Make sure that the safety belts are not be twisted.
   • In order to prevent the child from falling out of the safety seat, the child should always be fastened with a safety belt to ensure that the waist belt well restrains the child’s pelvic bones.
   • After a severe accident, the child safety seat should be replaced.
   • For the safety of the child, please do not modify this product by yourself. In order to obtain maximum protection for children please strictly follow the installation provided by the manufacturer.
   • Keep the car seat away from direct sunlight or cover it up with a light-colored The surface of the car seat may heat up and cause serious burns on the children’s skin.
   • It’s forbidden to leave the child unattended in the car seat, even if it’s for only a few minutes.
   • All luggage and items in the vehicle should be properly secured in case of
   • This product must always be used with the textile Please do not use replacement covers other than those recommended by the manufacturer. The textile covers affect the overall performance of the product.
   • This product is suitable for children weighing between 0kg-36kg.

• This product can only be installed in rear-facing mode before the child is 18kg and the seat cannot be installed on the front seat where there is an active When using forward facing installation after the child has 18kg, try to install the safety seat in the rear seat. The front seat with an airbag can easily cause injures for the child.
• This manual can be stored in the holding bag reserved for the child safety seat during the product service life.
• This product is not designed for home use, it may only be used in the car, please do not use it at home.
• Please always secure the car seat in the isofix or seat belts, even when there is no child using it. In case you don’t want to secure it, please store it in the
• During the daily use of the product, make sure that all parts of the child safety seat are fixed in the correct position and do not get stuck on the movable seat or door.
• Do not make any adjustments on the car seat with the child in it. First remove the child from the car seat and then perform the adjustments.
• Do not buy second-hand car child safety seats, because you have no way of knowing the history of the product. The likelihood of accidents is possible even if there are no key components missing or other visible damages.
• Do not use any other stress points other than those indicated, otherwise the safety cannot be guaranteed.
• Please contact the manufacturer if you have any doubts about this product’s installation.

WARNING! Products without certification and modified products are dangerous. In addition to this, not following the instructions can also affect the safety guaranteed by the product. If the adult seat belt interferes with the position of the main force point of the child restraint system, it cannot be used. If you have any questions about this, please contact the manufacturer of the child restraint system.

Notice regarding Universal category (Group 0+ I II III)

1. This product is labelled as a “Universal” child restraint system. It is approved by the ECE R44/04 regulation series of amendments, for general use in vehicles and it will fit most, but not all, vehicles.
2. A correct fit is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehicle is capable of accepting a “Universal” child restraint for this age group.
3. This child restraint system has been classified as “Universal” under more strict conditions than those applied to earlier designs which do not carry this
4. If in doubt, consult either the child restraint manufacturer or the retailer. Notice regarding Semi-universal category (Group 0+ I II III)

This child restraint is classified for ” Semi-universal” use and is suitable for fixing into the seat positions of the following cars:

Seat positions in other cars may also be suitable to accept this child restraint system. If in doubt, consult either the child restraint manufacturer or the retailer. Notice regarding Semi-universal ISOFIX child restraint system (in Group 0+)

1. This is an ISOFIX CHILD RESTRAINT SYSTEM. It is approved by Regulation 44, 04 series of amendments for general use in vehicles fitted with ISOFIX anchorage systems.
2. It will fit vehicles with positions approved as ISOFIX positions (as detailed in the vehicle handbook), depending on the category of the child seat and of the fixture.
3. The mass group and the ISOFIX size class for which this device is intended is: Group 0+, D.

2. INSTALLATION TIPS

• Rearward facing

Attention! When the child seat is installed in rear facing position, if it is hit by the car airbag, it will cause fatal injury or even death of the child.
Under no circumstances can this child safety seat be used on a car seat with an airbag activated.
Please read the instructions carefully to use the child safety seat correctly.
Do not install the child safety seat at the front seat when the airbag is active.
Only use with the 3-point safety belt.

2.2   Forward facing

Only suitable if the approved vehicles are fitted with 3-point safety belts, approved to UN/ECE Regulation No.16 or other equivalent standards.
Do not install the child safety seat at the front seat when the airbag is active.
Only use with the 3-point safety belt.

3.   INSTRUCTIONS for ISOFIX

• ISOFIX
  • If your vehicle is not equipped with an isofix guide sleeve, please insert the 2 isofix guide sleeves (02) attached to this child safety seat into the isofix fixing device (01).

Tip: The isofix is located between the seat of the vehicle and the backrest. Please read the description of isofix fixing points in the car manufacturer’s manual.

• Press the release button (13) of the isofix and push the isofix button to release it to the maximum.

• Headrest adjustment when using the 5-points harness (Gr 0+,I)

  • Press the central adjuster (04) and pull out the two shoulder belts (05) at the same time. Please do not pull the shoulder pads (06), try to release the 5- point safety belt to a longer position.

Warning! The outlet end of the shoulder strap cannot be lower than the child’s shoulder or higher than the height of the ear.

• Pull up the headrest adjustment ring (07) to adjust the headrest (08) to a suitable position for the child and fix it.

3.3   Headrest adjustment when using the 3-points belt (Gr II + III)

• Pull up the headrest adjustment ring (07) to adjust the headrest (08) to a suitable position for the child and fix it.
• The correctly adjusted headrest (08) of the safety seat ensures that the diagonal part (09) of the car seat belt is in the best position, which can provide the best protection for children. The safety seat headrest (08) must be adjusted to approximately two fingers between the child’s shoulder and the safety seat headrest (08).

3.4   Recline angle adjustment and rotation adjustment

• Press the adjusting handle (10) in the direction of the arrow to bring the car seat’s body (11) in the unlocked state, then adjust the car seat’s body (11) to a proper position, release the adjusting handle (10), and thus automatically locking again the product, now in a desired recline position.
• Press the adjusting handle (32) in the direction of the arrow to bring the car seat body (11) in an unlocked state, so that the car seat body (11) can be adjusted to rotate in a proper When you release the adjusting handle

(32) the car seat’s body will be automatically locked again.

Installation instructions

4. Installation instructions for group 0+ (0-13kg )
   • Installation with ISOFIX+Top tether+ 5-points harness
   • Please refer to chapter 3.1 to prepare the isofix.
   • Please ensure that the five-point safety belt is correctly installed on the child safety (Refer to Chapter 7)
   • Please refer to section 3.2 to adjust the 5-point safety belt.
   • Please refer to Chapter 4 to adjust the car seat’s body (11) to the most reclined position and in a locked state (not sliding and not rotating).
   • Reconfirm that the seat is at the most reclined angle position, explicitly when the sticker on the seat is aligned with the R position on the base, and then the child seat is installed facing the vehicle.

The position in the opposite direction is on the vehicle seat.
Note: When using by children in group 0+, be sure to adjust the gear to gear.

• Please connect two isofix connectors (12) by inserting them into the FIX guide sleeve (02) until you hear a “click” sound, at this time the ISOFIX indicator turns green.

Note: The isofix connector (12) is installed correctly only when the isofix indicator turns completely green.

• Push the safety seat firmly until it is close to the back of the vehicle seat.
• Press and hold the button of the top tether and release the top tether to a proper length.
• Put the top tether into one of the guides (14) on the
• Please hook the top tether fixing hook to the one recommended in the vehicle user manual.
• Pull the free end of the top tether to tighten until the indicator of the top tether turns completely green.
• please refer to page 18, 19 to install the child in the car seat.
• To use the 5-point harness, press the button to open the five-point safety buckle (19), then

press the central adjuster (04) and pull out the shoulder belt (05). Please do not pull the shoulder pad (06).

• Make sure that the child’s back rests flat on the safety seat. Close the two bolts (20) of the 5-point safety buckle first, and then insert them into the lock. When the buckle is locked correctly, a “click” sound will be heard.
• Pull the central adjustment belt (21) until the 5-point safety belt is close to the child.

4.2   Children in Group 0+ I (0-18kg) 3-point belt + 5-point harness

• Adjust the car seat in rear-facing position.
• Draw out the car’s 3-point seat belt to the longest.
• Pass the shoulder strap of the car’s 3-point seat belt through the seat belt guide hook on the side of the seat.
• Pass through the bottom of the car seat and tighten the car’s 3-point seat belt to its tightest.
• Pass the seat belt through the seat belt guide on both sides of the seat and close the buckle.

In order to ensure the safety of your children, please check the

following after each installation:

1. Make sure that the two isofix connectors are correctly connected to the vehicle isofix fixed point, and the isofix indicator is completely green.
2. Ensure that the child safety seat is tightly attached to the vehicle seat.
3. Make sure that the upper strap is tight and the upper strap indicator is green.
4. Make sure that the 5-point seat belt is close to the child, but not squeezing
5. Make sure that the shoulder strap is adjusted correctly and not twisted.
6. Make sure that the height of the shoulder pads is the same as the height of the child’s shoulders.
7. Make sure that the five-point buckle is locked.

5.  Installation instructions for Group I (9-18kg)

• Group I (9-18kg) children 3-points belt+5-points harness

  • Please make sure that the five-point harness is correctly installed on the child safety seat. (Refer to Chapter 7)
  • Please refer to Section 3.2 to adjust the five-point harness.
  • Please refer to Section 4 to adjust the car seat’s body (11) to a proper position and confirm that it is in the locked state (not sliding).
  • Please refer to section 5 to adjust the car seat body (11) to the forward position and confirm that it is in the locked state (cannot be rotated).
  • Please place the child safety seat on the vehicle seat in the same direction as the vehicle.
  • Please adjust the child safety seat to the F position. The seat has two positions F and R. The F position is the upright position, and the R position is the inclined position (for rear-facing direction).

• Pull out the 3-point safety belt of the vehicle, and slide the abdominal belt from the gap between the base (22) and the seat body (11) into the two base belt guide hooks (23) in the direction of the arrow. Insert the vehicle seat belt socket into the lock buckle and tighten the vehicle seat belt.

• Then place the vehicle 3-point belts behind the newborn inlay, between the back of the child seat and the inlay.

• Tighten the vehicle seat belts to ensure that there is no slack and

• Please follow the steps of “4.1.14” for children who use 5-point harness and place the chid in the car seat.

In order to ensure the safety of the child, please check the following

items after each installation:

1. Make sure that the vehicle seat belt is not twisted and in a tightened state.
2. Make sure that the child safety seat is close to the vehicle seat.
3. Make sure that the 5-point seat belt is close to the child, but not squeezing the child.
4. Ensure that the adjustment of the shoulder strap is correct and not twisted.
5. Make sure that the height of the shoulder pad is the same as the height of the child’s shoulders.
6. Ensure that the 5-point buckle is locked.

5.2 Children in Group I (9-18kg) isofix +3-point car belt + Five-point

harness

• Please make sure that the five-point harness is correctly installed on the child safety seat. (Refer to Chapter 7)
• Please refer to Section 3.2 to adjust the five-point harness.
• Please refer to Section 3.4 to adjust the car seat body to a proper position and confirm that it is in the locked state (not sliding).
• Please refer to section 3.5 to adjust the car seat body to the forward position and confirm that it is in the locked state (cannot be rotated).
• Please place the child safety seat on the vehicle seat in forward facing
• Please adjust the child safety seat to the F position. The seat has two positions F and R. The F position is the upright position, and the R position is the inclined position (for rear-facing direction).
• Pull out the 3-point safety belt of the vehicle and slide the abdominal belt in the gap between the base and the seat body into the two base belt guide hooks in the direction of the arrow. Insert the vehicle seat belt socket into the lock buckle and tighten the vehicle seat belt.
• Then place the two vehicle 3-point safety belts behind the newborn inlay, between the backrest of the child’s seat base and the inlay.
• Tighten the vehicle seat belts to ensure no slack or
• Please follow the steps of “4.1.14” for children to use 5-point safety belt and place the child in it.

To ensure the safety of the child, please pay attention to check the

following observations after each installation:

1. Ensure that the vehicle seat belt is not twisted and is in a tightened state.
2. Make sure that the child safety seat is close to the vehicle seat.
3. Make sure that the 5-point seat belt is close to the child, but not squeezing the child.
4. Ensure that the adjustment of the shoulder strap is put correctly and not
5. Make sure that the height of the shoulder pad is the same as the height of the child’s shoulders.
6. Ensure that the 5-point buckle is locked.

6.  Installation instructions for Group II (15-22kg), III Group (22-36kg)

• Group II (15-22kg), III Group (22-36kg) 3-points car belt

  • Please ensure that the five-point safety belt of the safety seat is properly (Refer to Chapter 7)
  • Please refer to Chapter 3.3 to adjust the headrest.
  • Please refer to Chapter 3.4 to adjust the car seat’s body and confirm that it is in the locked state (not sliding or rotating).
  • Place the child safety seat on the vehicle seat in forward- facing and place the child in the product.
  • Please adjust the child safety seat to the F angle position. The seat has two positions F and R, R is reclined and F gear is upright.
  • Pull out the vehicle seat belt around the child, and insert the vehicle seat belt insert plate into the lock buckle, when it is locked, a “ticking” sound will be Warning: Ensure that the vehicle seat belt is not twisted.
  • Place the vehicle seat belt waist belt and abdominal belt on the side of the vehicle seat belt buckle -under the child’s arm and place it in the belt guide groove inside.
  • Place the other side of the vehicle seat belt belly belt in the belt guide grove on the other
  • Put the upper part of the vehicle seat belt shoulder into the grove of the belt guide hook on the headrest to ensure that the vehicle seat belt is not
  • Please make sure that the upper part of the vehicle seat belt is placed on the child’s collarbone, not on the child’s neck.

• Group II (15-22kg), Group III (22-36kg) ISOFIX3 + 3 points car belt

  • Please ensure that the five-point safety belt of the safety seat is properly (Refer to Chapter 7)
  • Please refer to Chapter 3.3 to adjust the headrest.
  • Please refer to Chapter 3.4 to adjust the car seat’s body and confirm that it is in the locked state.
  • Place the child safety seat on the vehicle seat in the same direction as the vehicle, and please let the child sit on the safety seat.
  • Please adjust the child safety seat to the F angle position. The seat has two gears F and R, and the F gear is upright.

• Pull out the vehicle seat belt around the child, and insert the vehicle seat belt insert plate into the lock buckle, when it is locked, a “ticking” sound will be Warning: Ensure that the vehicle seat belt is not twisted.

• Place the vehicle seat belt waist belt and abdominal belt on the side of the vehicle seat belt buckle under the child’s arm and place it in the belt guide

• Place the other side of the vehicle seat belt, belly belt in the belt guide grove on the other

• Put the upper part of the vehicle seat belt shoulder into the groove of the belt guide hook on the headrest to ensure that the vehicle seat belt is not

• Please make sure that the upper part of the vehicle seat belt is placed on the child’s collarbone, not on the child’s neck.

Tip: If necessary, you can still adjust the headrest now.

7.  Hiding the Five-point harness for Group II, III(15-36 kg)

• Loosen the harness.
• Release the buckle.
• Adjust the child seat to maximum angle and turn it to the bottom. Turn the harness locking clip on their narrowest end and thread it through the slot under the bottom of the child seat. Now the crotch pad and buckle as well as harness straps can be
• Turn the buckle so it can be release from the back of the seat, after that remove the top tether system.
• Unlock the snap fastener, pull in all directions (according to the image) to take out the cover.
• Release the buckle, then remove the safety belt.
• Remove the shoulder pads.

Notice: Follow the process in reverse order to put on the fabric cover.

8.  Cleaning and maintenance

The cloth cover of the child safety seat can be removed and washed. Disassembly of the cloth cover:

1. Adjust the headrest to the highest position.
2. Remove the headrest cloth
3. Remove the car seat body

Wash the textile cover of the car seat in a delicate cycle on a temperature up to 40ᵒ. Use mild detergent. Don’t use bleach, don’t dry in dryer, don’t iron and don’t use unsuitable detergents

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>