coccolle Mago iSize Car Seat User Guide
- June 1, 2024
- coccolle
Table of Contents
coccolle Mago iSize Car Seat
Product Specifications
- iSize Range: 40-150 cm
- Regulation: UN Regulation NO.129
- Child Restraint System: I-Size Enhanced
- Approved for Use in I-Size Compatible Vehicle Seating Positions
Product Usage Instructions
Spare Part List:
-
1. Headrest
- Shoulder pad
- Shoulder strap
Adjusting the Buckle:
To open the buckle, press the red button until the latches come out. To lock the buckle, guide the two latches together into the harness buckle house until you hear a click.
Adjusting the Harness:
To tighten the harness, pull the adjuster strap until it lies flat against your child’s body. To loosen the harness, press the central adjuster and pull both shoulder belts forward. Ensure proper spacing between the child and the shoulder harness.
Adjusting the Recline Position:
The car seat has five reclining positions. In rearward-facing mode, use the most reclined position. In forward-facing mode, all five positions are usable. Pull the recline lever while inclining the seat to the desired position.
Adjusting the Anti-Rebound Bar:
FAQ
- Q: Can this car seat be used in all vehicles?
- A: The car seat is designed to be used in I-Size compatible vehicle seating positions. Refer to your vehicle user’s manual for compatibility information.
- Q: How many recline positions does the car seat have?
- A: The car seat has five recline positions that can be adjusted based on whether it is rearward or forward-facing.
The images shown in this instructions manual have illustrative purposes. The product purchased by you may look different.
Coccolle Mago iSize 40-150 cm car seat
Please read this manual carefully before use. Notice! This is an “I-Size Enhanced Child Restraint System”, it is approved according to UN Regulation NO.129, for use in I-Size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle user’s manual. If you have any doubts, consult either the car seat manufacturer or the retailer.
Safety warnings
- The rigid items and plastic parts of this car seat should be located and installed so that they are not liable to become trapped by a movable seat or in a door of the vehicle during everyday use of the vehicle;
- Any straps holding the car seat to the vehicle should be tight, any straps restraining the child should be adjusted to the child’s body, minding them not to be twisted;
- Ensure that any lap strap is worn low down, so that the pelvis is firmly engaged, otherwise injuries might occur.
- The car seat should be replaced if it has been involved in any accident;
- It is dangerous to make any modifications or additions to the car seat, and a danger to not follow closely the installation instructions provided by the manufacturer;
- When not in use, the car seat should be kept away from sunlight, otherwise it may become too hot for the child’s skin;
- Never leave your child unattended in the car seat;
- Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.
- The car seat shall not be used without the cover;
- The car seat cover should not be replaced with any other than the one recommended by the manufacturer, because the cover constitutes an integral part of the car seat performance.
- Retain the instructions on the child car seat for its life period.
- For an “I-Size Enhanced Child Restraint System”, the user shall also be referred to the vehicle manufacturer’s user guide.
Warranty conditions
- The warranty does not cover:
- Damage occurred for reasons attributable to the user.
- Damage occurred as a result of failure to use the product according to recommendations, warnings, and restrictions found in the user manual and on product elements.
- Consumables subject to natural wear and tear during normal usage such as: tires, inner tubes, tread, materials used on handles, structure and color of fabrics and materials subject to friction, sleeves in wheels, axels, prints.
- Damage occurred as a result of failure to observe maintenance guidelines such as: corrosion, changed upholstery or plastic elements color as a result of prolonged exposure to sunlight, damage to plastic elements of upholstery as a result of prolonged exposure to sunlight or excessive temperatures, excessive play, squeaking / creaking noises, damage to mechanism due to overload.
- Damage occurred due to repairs being carried out by unauthorized personnel.
- Single wheels being pushed into a vertical position as a result of loading (this is normal).
- Damage and soiling occurred due to the product being incorrectly packaged for shipping (courier online purchases).
- The repair method is determined by the manufacturer/warranty service provider.
- The product subject to a complaint should be provided clean.
- The consumer goods warranty does not exclude or suspend the purchaser’s rights stemming from goods noncompliance with the agreement.
Spare part list:
- Headrest
- Shoulder pad
- Shoulder strap
- Central adjuster
- Adjuster strap
- Rotation button
- Support leg
- Support leg adjustment buttons
- Belt holder
- Buckle
- Lower belt guide
- Recline lever
- Isofix connector
- Headrest height adjuster
- Instruction manual compartment
- Anti-rebound bar
- Anti-rebound bar button
- Isofix insert guide
- Side protection shield
- Infant cushion
Use in the vehicle
Please observe the instructions for using this car seat in your vehicle user’s manual. During use, be sure to observe any restrictions related to airbags. Please refer to the operating instructions for your vehicle for information about vehicle seats which are certified for the use of children’s restraining systems according to UN regulation No. 16.
This is an “I-Size Enhanced Child Restraint System”. It is approved to Regulation UN R129/03, for use in I-size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle user’s manual. If your vehicle does not have an I-size seating position, please check the vehicle type list that is included. DO NOT use this car seat in seating positions where an active frontal airbag is installed, serious injury can occur.
Adjusting the buckle
Open buckle : Press red button until buckle latches come out from the buckle. (fig.1)
Lock buckle: Guide the two buckle latches together (fig.2), putting them into the harness buckle house(fig.3). Buckle locked when sounds click (fig.4).
Notice: the buckle cannot lock only by putting one latch.
Adjusting the harness
To tighten the harness : pull the adjuster strap until the harness lies flat and is close to your child’s body (fig.5). Notice: Make sure the space between the child and the shoulder harness is about the thickness of one hand.
To loosen the harness : press the central adjuster and at the same time pull both shoulder belts forward. (fig.6) Do not pull on the shoulder pads.
Adjusting the headrest
Important! A correctly adjusted headrest ensures optimal protection for your child in the car seat.
When installed by 5-point harness, the headrest must be adjusted so that the shoulder belts are at the same level as your child’s shoulders(fig.7). Caution! The shoulder belts must not run behind the back of the child or at ear height or above the ear. When installed by a 3-point vehicle belt, the headrest must be adjusted so that there is a space of two fingers wide between the headrest and your child’s shoulders. Make sure the diagonal seat belt section is on the child’s shoulder but not on the neck. (fig.8) First loosen the harness. Squeeze the headrest height adjuster at the same time slide headrest to shoulder height in accordance with the height of the child. (fig.9)
Adjusting the recline position
the car seat has five recline positions. In the rearward-facing position, it can be used only in the most reclined position. For forward facing, all five positions may be used. Except for the most upright position, there is a slight chance that the other position may not fit in all approved vehicles. Pull the Recline lever at the same time incline seat to the intended position. (fig.10)
Adjusting the anti-rebound bar
The anti-rebound bar has two positions: reclined and upright. A forward-facing mounted car seat can only use the upright position. Rotate the seat lateral facing. Pull up the anti-rebound bar button then adjust the position of the anti-rebound bar.
Rotating the car seat
Pull the rotation button at the same time to rotate seat to the intended
direction. (fig.15,16)
When the seat rotates is fixed in the desired direction, the rotation button
will bounce back and make a click sound. Then try to rotate seat to make sure
the seat is locked. (fig.17)
Installation of the isofix
If your vehicle is not equipped with the isofix insert guides as standard, clip
the two insert guides that are included with the car seat.
On both sides of the car seat press the isofix release button and pull out the
isofix connectors in the longest position (fig.19,20). Slide the two isofix
connectors firmly into the insert guides until the isofix connectors engage with
a clicking noise on both sides. The isofix buttons must turn green on both
sides (fig.21,22). Push the child car seat towards the backrest of the car’s
seat applying firm, even pressure on both sides. Shake the child’s car seat to
make sure it is safely attached and re-check the green safety buttons to make
sure that both sides are completely green (fig.23).
Removal of the isofix
Push the child seat towards the backrest firmly (fig24). At the same time press the isofix button and pull back isofix connectors (fig.25).
Support leg installation
Pull the support leg away from the bottom of the seat until it is fully extended. Push both adjustment buttons and pull out the support leg until it rests firmly on the floor of the vehicle. Make sure the indicator on the support leg turns green, the bottom of the car seat does not lift up from the surface of the vehicle seat and two adjustment buttons are engaged.
Removal and installation of the safety harness
Loosen the press studs on the backrest and fold the upper half of the cover upwards and the lower half downwards (fig.30). Loosen the 5-point harness on the child car seat as far as possible. Then open the buckle (fig.29). Open the two shoulder pads by the Velcro fasteners on the side. Push the Velcro strip of the two opened shoulder pads under the backrest cover and attach it to the fleece strip provided (fig.31). Insert the buckle tongues in the recess provided on the inside of the backrest (fig.32). Open seat cover and fold the cover forwards, pull the harness buckle out of the cover (fig.33). Stow the harness buckle in the recess provided (fig.34). Close the two press studs and put back on the seat cover (fig.35). to refit the harness, simply follow the steps in the opposite order. Make sure the belt is not twisted.
Installation and removal of the side impact shield
This car seat has been tested and approved to offer optimum side protection without a side impact shield. The side impact shield is optional for extra side protection, but mind the fact that when used it may not fit in all approved vehicles. The side impact shield should be installed at the side which is close to the vehicle door. To install, insert the clip-on side impact shield onto the seat side wing was marked with two dents. Pull out the hook by pressing the button on the side impact shield and hook into the hole on the seat side wing. To remove, press the button then unhook from seat side, and slide out the side impact shield from the seat side wing.
Rearward-facing installation 40-105cm (born to approx. 4 Years, ≤ 18 kg)
Notice : The infant cushion protects your child. It needs to be used up
to a height of 75 cm. Pull away the support leg from the seat bottom, for more
leg space adjust the anti-rebound bar in a recline position. Rotate the seat
to rearward facing (fig 38) and adjust the seat in the most reclined position
(fig 39). Place the seat in a direction opposite to the direction of travel
(fig.40). Have your child sit down in the child seat. Adjust the headrest in
proper height (see section 4.3), adjust the harness and lock the buckle, then
tighten the harness (fig. 42).
Forward-facing installation 76-105cm (15 months to approx. 4 years, ≤ 18 kg)
Important! Do not use forward-facing before the child has not reached the age of 15 months.
Pull away the support leg from the seat bottom and adjust the rebound bar in the upright position. Rotate the seat to a forward-facing position (fig.43). Place the seat in a direction facing to travel (fig.44). Install the isofix connectors. Install support leg (fig.45). Have your child sit down in the car seat. Adjust the headrest in a proper height (see section 4.3), adjust the harness and lock the buckle, and finally tighten the harness. (fig. 46)
Forward facing installation 100-150cm (approx. 3 years to 12 years) Remove the safety harness when your child has reached a stature between 100 and 150cm.
Make sure that the support leg is stored on the bottom of the seat and adjust the anti-rebound bar in an upright position. Rotate the seat to a forward- facing position. Place the seat in a direction facing to travel (fig47,48). There are two options to install: only using the vehicle 3-point belt or using the vehicle 3-point belt together with isofix connectors.
Caution! In both options you don’t use the support leg.
Installing the isofix connectors (fig.49).
Have your child sit down in the child car seat. Adjust the headrest in the proper height. Pull out the vehicle seat belt and guide it in front of your child to the vehicle seat buckle. Engage the buckle tongue in the vehicle seat buckle (fig.50). Caution! The vehicle seat belt buckle must not be positioned in the lower belt guide. Place the diagonal seat belt section and lap belt section on the side of the vehicle seat belt buckle in the lower belt guide (fig.51). Place the lap belt section on the other side of the child car seat in the lower belt guide (fig.52).
Caution! The lap belt section must lie as low as possible over your child’s hips on both sides.
For child stature 100-150 cm installation, this child car seat also can use a vehicle belt only, it has been tested for it. If you want to use only vehicle belt installation, just skip the Isofix connectors relative content. Guide the diagonal belt section into the belt holder and it is not twisted (fig.53).
Cleaning and maintenance
The cover can be removed and washed. Please observe the instructions on the washing label of the cover. Loosen the press studs at the back of the headrest and remove the cover of the headrest. Loosen the press studs and unzip the back of seat cover. Pull forward and remove seat cover. To refit the cover simply follow the steps in the opposite order.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>