coccolle 100-150 cm Eris Eris Dessert Rose Smart Baby Instruction Manual

coccolle 100-150 cm Eris Eris Dessert Rose Smart Baby

The images shown in this instructions manual have illustrative purpose. The product purchased by you may look different.

Coccolle Eris Isize 100-150 cm child car seat

Please read this manual carefully before you start installing the product and remember to keep it for future reference. A wrong installation may pose a threat to the child’s health.

Attention

This is an iSize booster seat Enhanced Child Restraint System. It is approved according to UN Regulation No. 129, for use primarily in “i-Size seating positions” as indicated by vehicle manufacturers in the vehicle user’s manual. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer

1. This product is intended for children whose height ranges from 100 to 150 cm (aged 4-12), with weight situated between 15 and 36 kg. This product may not fit some vehicles in case your child’s height is 135-150 cm.

2. Hard components and plastic parts of the child restraint system must be placed and installed in a way that they are not trapped by sliding seat or vehicle door under normal conditions of use.

3. All belts which secure the car seat must be tight and adapted to child’s body.
   Make sure that the belts are not be twisted.

4. All hip belts must go low so that the child’s pelvis is held properly

5. The product must be replaced if it has been exposed to overloads in case of accident.

6. Do not make any modifications or supplementation to the product. Please strictly follow the instructions’ manual.

7. Make sure the product is not exposed to direct sunlight. It may cause the product to heat up and, in effect, burn the child’s skin.

8. Do not leave the child in the car seat unattended.

9. Luggage and other items which may cause injuries in case of car collision must be properly secured.

10. Do not use the child safety seat without its fabric cover. Do not replace the cover with other parts apart from those recommended by the manufacturer. The cover is an integral part of the car seat.

11. Buckle the product correctly and properly. In case of emergency, proper protection of buckles lets you take the child out of the car seat easily.

12. Before you install the car seat, please read the vehicle’s manual too.

Warranty conditions

1. The warranty does not cover:
   • Damage occurred for reasons attributable to the user
   • Damage occurred as a result of failure to use the product according to recommendations, warnings and restrictions found in the user manual and on product elements.
   • Consumables subject to natural wear and tear during normal usage such as: tires, inner tubes, tread, materials used on handles, structure and colour of fabrics and materials subject to friction, sleeves in wheels, axels, prints.
   • Damage occurred as a result of failure to observe maintenance guidelines such as: corrosion, changed upholstery or plastic elements colour as a result of prolonged exposure to sunlight, damage to plastic elements of upholstery as a  result of prolonged exposure to sunlight or excessive temperatures, excessive play, squeaking / creaking noises, damage to mechanism due to over- load.
   • Damage occurred due to repairs being carried out by unauthorised personnel.
   • Single wheels being pushed into a vertical position as a result of loading (this is normal).
   • Damage and soiling occurred due to the product being incorrectly packaged for shipping (courier online purchases).

2. The repair method is determined by the manufacturer/warranty service provider.

3. The product subject to a complaint should be provided clean.

4. The consumer goods warranty does not exclude or suspend the purchaser’s rights stemming from goods noncompliance with the agreement.

Parts list (fig. 1)

1. Adjustable headrest
2. Headrest adjustment
3. Shoulder belt guide
4. Hip belt guide
5. Car seat base
6. Inclination adjustment lever
7. ISOFIX arms
8. ISOFIX release key
9. ISOFIX control light
10. ISOFIX fastening spots
    

Installation method

If the car seat cannot be installed with the use of ISOFIX fastening spots in the vehicle, ISOFIX fasteners may remain hidden inside the car seat, and the car seat may be therefore installed with the use of three-point safety belts. By installing the child safety seat on the front seat of the vehicle, make sure the backrest of the vehicle seat is in vertical position.

With three-point safety belts and ISOFIX fasteners

1. Place the child safety seat inside the car. Grip and pull ISOFIX release key to pull ISOFIX arms out (fig. 2). ISOFIX arms work properly when you pull them out fully.

2. Press ISOFIX fasteners against ISOFIX fastening spots in the vehicle (fig.3).
   Make sure all ISOFIX control lights are GREEN ( fig. 4). Press the child restraint system against the vehicle seat backrest as much as you can.

3. Put the child in the car seat.

4. Carry the shoulder belt through the shoulder belt guide (fig. 5). Carry the hip belt through the hip belt guide (fig. 9). Fasten safety belts. Make sure the belt is not twisted (fig. 9A).
   

With three-point safety belts only

Place the child safety seat on the vehicle seat. Carry the shoulder belt through shoulder belt guide (fig. 5). Carry the hip belt through hip belt guide (fig. 9). Fasten safety belts. Make sure the belt is not twisted (fig. 9A).

How to put the child in

1. Adjust the headrest to child’s height by pressing the height adjustment (fig. 6).
   Adjust the headrest so that there is a finger thick space between the headrest and child’s arms (fig. 7).

2. The car seat can be inclined in three positions. Set the car seat in a suitable position before you secure the child with safety belts (fig. 8).

3. Fasten safety belts (fig. 9). Make sure the belt is not twisted (fig. 9A).
   
   

How to take the car seat out

1. Remove the shoulder belt from the shoulder belt guide and hip belt from the hip belt guide (fig. 10).
2. Press ISOFIX release key to release and retract ISOFIX fasteners (fig. 11).
3. Take the car seat out of the vehicle.
   

How to remove fabric cover and put it back on

1. The fabric cover is mounted with the use of elastic hooks.
2. When you wish to remove the cover, start from car seat backrest cover.

Cleaning and maintenance

1. The fabric cover can be machine washed on delicate cycles at maximum 30°C.
2. Do not tumble dry, make sure you line dry in shaded places.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>