NEXT LEVEL RACING WS 2.0 Wheel Stand Instruction Manual
- June 5, 2024
- next level RACING
Table of Contents
TAKE RACING TO THE NEXT LEVEL
NEXT LEVEL RACING® WHEEL STAND 2.0
INSTRUCTION MANUAL
YOUR
SIM RACING JOURNEY STARTS HERE
We know you’re eager to start racing! Take your time with the instructions and
follow this guide to assemble your product. You’ll be setting yourself up for
success with following the instruction booklet to fully optimize your product.
https://www.nextlevelracing.com/next-level-racing-video-instructions-and- tips/https://www.nextlevelracing.com/follow-us/
| @next_level_racing
---|---
| @nextlevelracingOfficial
| @nextlvlracing
| Next Level Racing
| [email protected]
TAKE RACING TO THE NEXT LEVEL®
NEXTLEVELRACING.COM
[email protected]
PRE-RACE CHECKS
WARNING
- Please do not use power tools for assembly as over-tightening can damage the frame.
- Layout and build the Wheel Stand on a level surface.
- Do not force parts together.
- Avoid cross-threading bolts.
- Ensure knobs are fastened tightly before lifting the folded Wheel Stand.
If you require any support with your product please contact our friendly team at: [email protected]
WARNING
CHOKING HAZARD – Small parts not for children under 3 years or any individuals
who have a tendency to place inedible objects in their mouths.
https://www.nextlevelracing.com/next-level-racing-video-
instructions-and-tips/
IN THE BOX
PARTS: NIL
WARNING:
Pinch Point Hazard, keep hands clear of the pivot area.
01 Loosen the two knobs circled to unfold wheel stand.
PARTS:
WARNING:
Be careful with fingers not getting pinched.
02 Cut the plastic ties, then lay down the pedal frame and reinstall the twist
knob at the front of the pedal frame.
PARTS:
03 Line up the back holes on the pedal plate with the back holes on the pedal
brackets and bolt through using 2 x M8 Bolts and Washers.
PARTS:
04 Adjust the pedal plate to your desired angle and bolt through the front
holes using 2 x M8 Bolts and Washers.
PARTS:
NIL
05 Align the pedal assembly with the threaded inserts on the wheel stand
pedal frame.
PARTS:
• 4x M8 16mm Knob 06 Install the knobs through the pedal assembly into the
threaded inserts. Adjust the pedal plate to your desired position.
PARTS:
07 Line up the front hole on the wheel plate
with the wheel post hole secure using 1x M8 55mm bolt, washer and nut. Repeat
on the other side.
PARTS: 08 Adjust the wheel plate to your preferred angle and bolt through
securing using 1x M8 55mm bolt, washer and nut. Repeat on the other
side.
PARTS: 09 Uninstall the preinstalled bolts on the vertical posts, adjust
to your desired height and re-install the bolts to lock your height in
place.
PARTS:
10 Line up the holes on the Shifter Mounting arm with the threaded inserts on
the Shifter Arm and bolt through with 4 x M8 16mm bolts and washers. Repeat on
other side.
PARTS: 11 Line up the holes on the Shifter Plate with the slots on the
shifter arm, bolt through and secure using 2 x M8 55mm Bolts, Washers and
Nuts.
PARTS:
12 Line up the holes on the handbrake plate with the threaded inserts on the
shifter plate, choose if you want the handbrake plate flat or angled. Bolt
through to secure using 2x M8 16mm Bolts and washers.
PARTS:
13 Line up the holes on the Shifter Mounting Arm with the threaded inserts on
the vertical post choose your desired height securing with 2x M8 16mm Bolts
and Washers. 
PARTS: 14 Install the Feet into the threaded inserts at the bottom of the
stand. Rotate the feet clockwise to tighten.
PARTS: 16 Line up the holes on the Gaming Chair Cradle assembly with the
threaded inserts on the wheel stand, bolt through using 2 x M8 16mm Bolts and
Washers.
PARTS:
NIL
17 Place two feet/wheels in the Gaming Chair Cradle.
PARTS:
NIL
18 Stow away the Gaming Chair Cradle as shown to allow easy folding of the
stand for storage.
PARTS:
NIL
19a Uninstall the Knob, and lift the pedal frame to line up the threaded
insert with the folding tab install the knob to secure the pedal assembly.
PARTS:
NIL
WARNING:
Make sure all knobs are tightened before lifting stand.
19b Loosen the Knobs on the pivot joint and pull the legs together to fold the
stand. Once folded tighten all knobs to secure stand.
PARTS:
NIL
20 Align the “Next Level Racing® GTSeat Add-on” with the wheel stand and
uninstall the plastic caps to expose the mounting holes.
PARTS: 21 Line up the holes on the “Next Level Racing® GTSeat Add-on”
with the threaded inserts on the “Next Level Racing® Wheel Stand 2.0” frame,
secure using 4 x M8 16mm Bolts and Washers.
PARTS:
TIPS: It will be easier to install when putting the bolt on the end of
the allen key.
22 Bolt through the “Next Level Racing® GTSeat Add-on” and secure using 2 x M8
16mm Bolts and Washers. Reinstall the plastic cap cover.
WARNING
Please do not use power tools for assembly as over tightening can damage the
frame.
Layout and building Wheel Stand on level surface.
Do not force parts together.
Avoid cross threading bolts.
Ensure knobs are fastened tightly before lifting the folded Wheel Stand.
ASSISTANCE
https://www.nextlevelracing.com/next-level-racing-video-instructions-and-
tips/
If you require further support with your product please contact our friendly
team at: [email protected]
NOTES
[email protected]