next level RACING GT LITE Pro Cockpit Instruction Manual

June 13, 2024
next level RACING

next level RACING GT LITE Pro Cockpit

next-level-RACING-GT-LITE-Pro-Cockpit-fig- \(2\)

Product Information

The Next Level Racing LITE is a sim racing cockpit that provides an immersive racing experience. It is designed to optimize your sim racing journey and enhance your racing skills. The cockpit features a fabric seat, a main frame, a backrest, a wheel plate, a pedal frame, and various other components for a sturdy and comfortable setup.|
The package includes all the necessary hardware for assembly, including bolts, nuts, washers, and tools. Some items come with a rust-resistant coating for durability.

Product Usage Instructions

Using NLR LITE Series Hubs

Before adjusting the hubs, ensure that the user is out of the cockpit.
Tighten the hubs fully before using the cockpit. Spin the hub clockwise to ensure it is tightly secured.
To unlock and lock the hubs, open and close the cam lever respectively. Make sure the cam lever is tightly closed by spinning it clockwise before sitting in the cockpit to avoid any failure.

Assembly Process

Insert the Backrest Bottom Tubes through the openings in the back of the Backrest. Press the spring-loaded pin to lock the tubes in place. The top holes will create a taller backrest, while the bottom holes will create a shorter one.
Uninstall the bolts and nuts from the Backrest Bottom Tube reclining hinges. Align the mounting holes on the Backrest Bottom Tube hinges with the Main Frame mounting holes. Bolt through and secure using the bolts and nuts uninstalled in Step 3A.

Backrest Adjustment

Pull out the reclining knobs to release them. Unfold the Backrest to your desired position. Release the reclining knob to lock the Backrest in place. Ensure that the pin is properly secured through the reclining hinge side plate to prevent any failure.
For any support or assistance with your product, please contact our friendly team at support@nextlevelracing.com.

We know you’re eager to start racing! Take your time with the instructions and follow this guide to assemble your product. You’ll be setting yourself up for success by following the instruction booklet to fully optimize your product.

ASSEMBLY VIDEOnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(3\)
bit.ly/nlrbuild

FOLLOW US

support@nextlevelracing.com

PRE-RACE CHECKS

WARNING

  • Please do not use power tools for assembly as over tightening can damage your frame.
  • Do not adjust the Hubs while sitting in cockpit.
  • Make sure the Hubs are tightened fully before using the cockpit (Spin the Hub clockwise to ensure it is fully tight).
  • Make sure the Wheel Deck strap on the Wheel Bar is tight when adjusting the Hubs, otherwise the Wheel Plate Tube will fall when Hubs are open.
  • Moving parts present a pinch hazard. Take care when adjusting to avoid injury.

If you require any support with your product please contact our friendly team at: support@nextlevelracing.com

WARNING CHOKING HAZARD – Small parts not for children under 3 yearsor any individuals who have a tendency to place inedible objects in their mouths

ASSEMBLY VIDEOnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(3\)
bit.ly/nlrbuild

IN THE BOX

next-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(5\)

PARTS

next-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(6\)

NOTE: Some items come with rust resistant coating

USING NLR LITE SERIES HUBS

Make sure the hubs are tightened fully before using the cockpit. (Spin the hub clockwise to ensure it is fully tight
Open and close the cam lever to unlock and lock the hubs respectively. Make sure the cam is tightly closed by spinning the lever clockwise before sitting in the cockpit to avoid failure

ASSEMBLY PROCESS

  • Insert the Backrest Bottom Tubes through the openings in the back of the Backrest. Press the spring-loaded pin to lock the tubes in place. Top holes will create a taller backrest and bottom holes will create a shorter onenext-level-RACING-GT-LITE-Pro-Cockpit-fig- \(8\)
  • Uninstall the bolts and nuts from the Backrest Bottom Tube reclining hinges. B) Align the mounting holes on the Backrest Bottom Tubes hinges with the Main Frame mounting holes. Bolt through and secure using the bolts and nuts uninstalled in Step 3Anext-level-RACING-GT-LITE-Pro-Cockpit-fig- \(9\)
  • Open the cam lever on the Hubs to allow them to move freely. B) Unfold the Front Leg. C) Lock the cam lever to lock the Front Leg in placenext-level-RACING-GT-LITE-Pro-Cockpit-fig- \(10\)
  • Pull out the reclining knobs. B) Unfold the Backrest. C) Release the reclining knob to lock the Backrest in place. Ensure the pin is properly secured through the reclining hinge side plate to prevent failure.next-level-RACING-GT-LITE-Pro-Cockpit-fig- \(11\)
  • Remove the pre-installed bolts and nuts from the Main Frame. B) Align the tube ends of the Back Leg with the tube openings of the Main Frame. Bolt through and secure using the bolts and nuts previously uninstalled.next-level-RACING-GT-LITE-Pro-Cockpit-fig- \(12\)
  • Insert the Pedal Front Tube into the Pedal Frame. Press the spring-loaded pin and slide the tube onto the frame until it clicks into place. Change the inclination of your pedals by installing the Pedal Front Tube upside downnext-level-RACING-GT-LITE-Pro-Cockpit-fig- \(13\)
  • Detach the two sides of the Pedal Frame Bracket. B) Install the Pedals Frame Brackets to the Front Leg. Bolt the two halves of the Pedal Frame Bracket together using the hardware uninstalled in Step 8A.next-level-RACING-GT-LITE-Pro-Cockpit-fig- \(14\)
  • Remove the bolt and nut pre-installed in the Wheel Plate Socket. B) Insert the Wheel Plate Tube into the left Wheel Plate Socket. C) Bolt and secure using the hardware previously uninstalled in Step 9A.next-level-RACING-GT-LITE-Pro-Cockpit-fig- \(15\)
  • Open the Wheel Plate Latch. B) Swing the Wheel Plate tube. C) Secure it in place by closing the Latch.next-level-RACING-GT-LITE-Pro-Cockpit-fig- \(16\)
  • Remove the bolt and nut preinstalled in the Shifter Socket. B) Align the Shifter and Handbrake Plate assembly with the Shifter Socket of your choice. Bolt and secure using the hardware pre-installed in the Shifter Socketsnext-level-RACING-GT-LITE-Pro-Cockpit-fig- \(17\)
  • Install the Wheel Plate strengthening strap following the indications on the pictures above. Do not overtighten to avoid damage to the cockpitnext-level-RACING-GT-LITE-Pro-Cockpit-fig- \(18\)
  • Connect the Strengthening Straps to the Wheel Plate Tube. Adjust these straps while seated in the cockpit with your feet resting on the pedals to prevent the frame from lifting off the ground when adjustingnext-level-RACING-GT-LITE-Pro-Cockpit-fig- \(19\)

WHEEL PLATE

**ANGLE ADJUSTMENT

next-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(20\)**

Loosen the knob under the Wheel Plate, adjust to the desired angle and tighten to lock the Wheel Plate in place

DISTANCE ADJUSTMENTnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(21\)

Uninstall the 4 x bolts securing the Wheel Plate to the Wheel Plate Tube. B) Move the Wheel Plate forward (tall users) or back (short users). Bolt and secure in new position using the hardware previously uninstalled

BACKREST

ANGLE ADJUSTMENT
next-level-RACING-GT-LITE-Pro-Cockpit-fig- \(22\)
Pull both knobs on the Backrest Hinges outwards. Change the inclination of the Backrest and release the knob. Make sure the pin is going all the way through the inner plate to avoid damaging the frame.

HEIGHT ADJUSTMENTnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(23\)

Press the spring-loaded pin and pull up or push down the top of the Backrest to choose your desired height.

BACK LEG

ANGLE ADJUSTMENTnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(24\)

Remove the bolts and nuts securing the Back Leg to the Main Frame. Choose any of the 3 different mounting holes and reinstall bolts to secure in place

FRONT LEG

HEIGHT ADJUSTMENTnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(25\)

Simultaneously press the spring-loaded pins on the sides of the Front Leg and adjust the Main Frame up to increase the distance to pedals. Step on the Front Leg to anchor the cockpit while adjusting to prevent it from lifting off the ground

PEDAL PLATES – DISTANCE ADJUSTMENTnext-level-RACING-GT-LITE-Pro-Cockpit-
fig- \(26\)

Loosen the ratchet handles securing the Pedal Plates in place. Adjust to the desired position and tighten the ratchet handles to prevent slipping while driving. Do not overtighten

REINFORCED LEGSnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(27\)

To increase the rigidity of your cockpit you can use one or both of the Packaging Straps to connect the Front Leg and Back Leg together.

FOLDING SEQUENCEnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(28\)

Disconnect all the straps before folding the cockpit

Undo the Hub’s cam levers and rotate anti-clockwise to allow the Hubs to spin freely. Grab the Wheel Plate tube and the top of the Backrest as shownnext-
level-RACING-GT-LITE-Pro-Cockpit-fig- \(29\)

Fold the cockpit to the front. Position the Wheel Base close to the pedals as shownnext-level-RACING-GT-LITE-Pro-Cockpit-fig- \(30\)

Pull both Backrest reclining knobs outwards and completely release the Backrest from the hinge to allow free movement. Fold the Backrest all the way forward as shown.next-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(31\)

Grab the Back Leg and push down gently to fold the Seat.next-level-RACING-
GT-LITE-Pro-Cockpit-fig- \(32\)

Use the Strengthening Straps to secure all parts together. Thread the straps through the Wheel Plate, Backrest and Pedal Framenext-level-RACING-GT-LITE-
Pro-Cockpit-fig- \(33\)

Close the Hub’s cam levers to secure the cockpit and prevent it from opening. B) Grab the Pedals Support Frame Tube and lift the cockpit until it is resting on the roller wheels. Move to the storage locationnext-level-RACING-GT-LITE-
Pro-Cockpit-fig- \(34\)

WARNING

  • Do not use power tools for assembly as over-tightening can damage the frame.
  • Do not adjust the Hubs while sitting in the cockpit.
  • Make sure the Hubs are tightened fully before using the cockpit.
  • Spin the Hub’s cam levers clockwise to ensure the Hubs are fully tight.
  • Make sure the strap on Wheel Bar is tight when adjusting the Hubs, otherwise, the Wheel Plate Tube will fall when the Hubs are open.

ASSISTANCE ASSEMBLY VIDEOnext-level-RACING-GT-LITE-Pro-Cockpit-fig-
\(3\)
bit.ly/nlrbuild

If you require further support with your product please contact our friendly team at: support@nextlevelracing.com
support@nextlevelracing.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals