next level RACING NLR-E034 Elite Shifter Add On Black Edition Instruction Manual
- June 10, 2024
- next level RACING
Table of Contents
next level RACING NLR-E034 Elite Shifter Add On Black Edition
Product Information: Elite Shifter Add-On
The Elite Shifter Add-On is a product designed for use with the Next Level Racing F-GT Elite Cockpit. It allows for the addition of a shifter to enhance the sim racing experience. The product comes with all necessary parts for assembly, including the shifter arm shifter arm support, shifter support connecting plate, shifter plate, corner brackets, shifter arm support bracket (left and right), T-nuts, bolts, washers, and end caps.
Pre-Race Checks
Before using the Elite Shifter Add-On, ensure all parts are present and in good condition. If you require any support with your product, contact the Next Level Racing team at support@nextlevelracing.com. Additionally, note that the product contains small parts that may pose a choking hazard to children under 3 years of age or individuals who have a tendency to place inedible objects in their mouths.
Product Usage Instructions
Follow these instructions to assemble the right-hand shifter mount. Note that for the left-hand shifter mount, skip to Step 16.
- Uninstall 4 x Ratchet Handles and 2 x Seat Slider Assemblies.
- Uninstall 2 x M8 40mm Bolts and M8 Washers connecting the Right Base to the Rear Base. Uninstall the End Cap and Cable Management Clip (if installed).
- Install 2 x Full Width T-Nuts into the top and bottom channels of the Right Base.
- Install the Bolts, Washers, Cable Management Clip (optional), and End Cap previously uninstalled in Step 02.
- Install 2 x Seat Slider Assemblies and 4 x Ratchet Handles previously uninstalled in Step 01.
- Uninstall the End Cap at the top of the Right Wheel Post. Install 4 x Full Width T-Nuts. Reinstall the End Cap.
- Align the Shifter Support Connecting Plate with the T-Nuts previously installed in Step 03. Bolt through and secure with 2 x M8 Bolts and Washers.
- Install 4 x Full Width T-Nuts into the Shifter Arm Support.
- Align the T-Nuts installed to the inside face of the Shifter Arm Support in Step 08 with the mounting slot on the Shifter Support Connecting Plate. Bolt through and secure with 2 x M8 Bolts and Washers.
- Install 10 x Full Width T-Nuts into the Shifter Arm.
For further assembly instructions, refer to the video instruction guide provided at bit.ly/nlrbuild. For support or assistance, contact Next Level Racing at support@nextlevelracing.com.
We know you’re eager to start racing! Take your time with the instructions and follow this guide to assemble your product. You’ll be setting yourself up for success with following the instruction booklet to fully optimize your product.
ASSEMBLY VIDEO
- @next_level_racing
- @nextlevelracingOfficial
- @nextlvlracing
- Next Level Racing
- support@nextlevelracing.com
TAKE RACING
TO THE NEXT LEVEL®
NEXTLEVELRACING.COM
PRE-RACE CHECKS
WARNING
- Please do not use power tools for assembly as over tightening can damage your frame.
- If you require further support, consult the installation video or contact us at support@nextlevelracing.com
- Please ensure T-Nuts are correctly placed within the extrusion.
- Lay out and build on a level surface.
- Beware of sharp edges on extrusion pieces.
- Do not force parts together.
- Avoid cross threading bolts.
If you require any support with your product please contact our friendly team at: support@nextlevelracing.com
WARNING
CHOKING HAZARD – Small parts not for children under 3 years or any individuals
who have a tendency to place inedible objects in their mouths.
ASSEMBLY VIDEO
IN THE BOX
*NOT TO SCALE
NOTE: Some Items Come with Rust Resistant Coating
Uninstall 4 x Ratchet Handles and 2 x Seat Slider Assemblies.
Uninstall 2 x M8 40mm Bolts and M8 W
Uninstall the End Cap and Cable Management Clip (if installed). ashers
connecting the Right Base to the Rear Base.
Red dots show TInstall 2 x Full Width T-Nuts placement. -Nuts into the top and bottom channels of the Right Base.
Step 02. Install the Bolts, Washers, Cable Management Clip (optional), and End Cap previously uninstalled in
Install 2 x Seat Slider Assemblies and 4 x Ratchet Handles previously uninstalled in Step 01.
Red dots show T-Nuts placement. RUninstall the End Cap at the top of the Right Wheel Peinstall the End Cap. ost. Install 4 x Full Width T-Nuts.
Bolt through and secure with 2 x M8 Bolts and WAlign the Shifter Support Connecting Plate with the Tashers. -Nuts previously installed in Step 03.
Red dots show TInstall 4 x Full Width T-Nuts placement. -Nuts into the Shifter Arm Support.
Align the T-Nuts installed to the inside face of the Shifter Arm Support in Step 08 with the mounting slot on the Shifter Support Connecting Plate. Bolt through and secure with 2 x M8 Bolts and Washers.
Install 10 x Full Width T-Nuts into the Shifter Arm. Red dots show T-Nuts placement.
- Install 2 x Corner Brackets on the top and bottom of the Shifter Arm. Bolt through and secure with 4 x M8 Bolts and Washer
- Install Shifter Arm Support Bracket (Right) to the bottom of the Shifter Arm. Bolt through and secure with 2 x M8 Bolts and Washer.
Align the Shifter Arm Assembly from Bolt through and secure with 6 x M8 Bolts and WStep 11 with the Tashers. -Nuts previously installed in Steps 06 and 08.
Bolt through and secure with 4 x M8 Bolts and WAlign mounting slot holes in the Shifter Plate with the Tashers. -Nuts previously installed in Step 10.
Install End Caps.
-
Loosen the Bolts securing the Shifter Plate. Adjust to the desired angle and position, tighten the Bolts to lock in place.
-
Loosen the Bolts securing the Shifter Arm to the Shifter Arm Support and the Wheel Post. Adjust to the desired height, tighten
the Bolts to lock in place. -
Loosen the Bolts securing the Shifter Support Arm to the Right Base. Loosen the bolts securing the Shifter Arm to the Wheel
Post. Adjust forward or backward to the desired position, tighten the Bolts to lock in place.
Uninstall 4 x Ratchet Handles and 2 x Seat Slider Assemblies.
Uninstall 2 x M8 40mm Bolts and M8 WUninstall the End Cap and Cable Management Clip (if installed). ashers connecting the Left Base to the Rear Base.
Red dots show TInstall 2 x Full Width T-Nuts placement. -Nuts into the top and bottom channel of the Left Base.
Step 17. Install the Bolts, Washers, Cable Management Clip (optional), and End Cap previously uninstalled in
Install 2 x Seat Slider Assemblies and 4 x Ratchet Handles previously uninstalled in Step 16.
Red dots show TUninstall the End Cap at the top of the L-Nuts placement. Reinstall the End Capeft Wheel P . ost. Install 4 x Full Width T-Nuts.
Bolt through and secure with 2 x M8 Bolts and WAlign the Shifter Support Connecting Plate with the Tashers. -Nuts previously installed in Step 18.
Red dots show TInstall 4 x Full Width T-Nuts placement. -Nuts into the Shifter Arm Support.
Align the T-Nuts installed to the inside face of the Shifter Arm Support in
Step 23 with the mounting
slot on the Shifter Support Connecting Plate. Bolt through and secure with 2 x
M8 Bolts and Washers.
Install 10 x Full Width T-Nuts into the Shifter Arm. Red dots show T-Nuts placement.
- Install 2 x Corner Brackets on the top and bottom of the Shifter Arm. Bolt through and secure with 4 x M8 Bolts and Washers.
- Install Shifter Arm Support Bracket (Left) to the bottom of the Shifter Arm. Bolt through and secure with 2 x M8 Bolts and Washers.
Align the Shifter Arm Assembly from Bolt through and secure with 6 x M8 Bolts and WStep 26 with the Tashers. -Nuts previously installed in Steps 21 and 23.
Bolt through and secure with 4 x M8 Bolts and WAlign the mounting slot holes in Shifter Plate with Tashers. -Nuts previously installed in Step 25.
29 Install End Caps.
- Loosen the Bolts securing the Shifter Plate. Adjust to the desired angle and position, tighten the Bolts to lock in place.
- Loosen the Bolts securing the Shifter Arm to the Shifter Arm Support and the Wheel Post. Adjust to the desired height, tight-en the Bolts to lock in place.
- Loosen the Bolts securing the Shifter Support Arm to the Left Base. Loosen the bolts securing the Shifter Arm to the Wheel Post. Adjust forward or backward to the desired position, tighten the Bolts to lock in place.
WARNING
- Please do not use power tools for assembly as over tightening can damage your frame.
- If you require further support, consult the installation video or contact us at support@nextlevelracing.com
- Please ensure T-Nuts are correctly placed within the extrusion.
- Lay out and build on a level surface.
- If you require further support with your product please contact our friendly team at: support@nextlevelracing.com
ASSISTANCE
ASSEMBLY VIDEO
Beware of sharp edges on extrusion pieces. Do not force parts together. Avoid cross threading bolts.
References
- Next Level Racing Video Instructions | Next Level Racing
- Video Instructions, Tips & Reviews | Next Level Racing
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>