Genius FSUGG00AB 20 Watts Bluetooth Wood Speakers User Guide

Genius FSUGG00AB 20 Watts Bluetooth Wood Speakers

Safety Instruction

Safety Instruction for CB and CE-LVD

1. Do not install this equipment in a confined or building-in space such as a book case or similar unit, and remain a well ventilation conditions. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains etc.
2. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus.
3. WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
4. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

The frequency band of product is 2.402GHz-2.48GHz and the radio-frequency transmitted maximum power (equivalent isotropic radiated power, EIRP) less than 10 mW.

• Operating temperature: 0 ~ 40°C

Product storage conditions

• Temperature: -20°C ~ 50°C / Humidity: 5%~ 85%

Symbol for Separate Collection in European Countries

This symbol indicates that this product is to be collected separately.
The following apply only to users in European countries:

• This product is designated for separate collection at an appropriate collection point. Do not dispose of as household waste.
• For more information, contact the retailer or the local authorities in charge of waste management.

Wireless Setup

Bluetooth pairing to a phone or entertainment device:

• Turn on your phone and ensure its Bluetooth function is activated.
• Press “Power/Source/Volume”button for 2 seconds to turn on speaker power and enter Bluetooth mode, and then press Tone/Bluetooth” button for 2 seconds to go to pairing mode. (Remark: 1.While the speaker power on for the first time,it’s in Bluetooth mode. 2.When in other modes, press “Tone/Bluetooth” button for 2 seconds it also can switch back to Bluetooth pairing mode.)
• Search for Bluetooth devices on your phone by following the phone’s instructions. Refer to your phone’s user manual for more information.
• After a few seconds, the phone will list the device as a “SP-HF 800BT”, select it and follow your phone instruction to select this pairing.
• Your phone will confirm the pairing, and then press Yes/Ok.
• Finally, select “connect with device” from your phone.

Connections

• (A) Speaker cable
• (B) AC power cord
• (C) Audio cable
• (D) USB

Jacks Info

1. Power/Source/Volume
2. Tone/Bluetooth
3. Headphone Jack

• Power Off (Red)
• USB (Green)
• Aux (Orange)
• Bluetooth Pairing (Blue light flashing)
• Bluetooth Paired (Blue light on)

Operation And Specification

Warning

1. Do not connect the power plug into an AC outlet until all connections are made.
2. Please remove AC power cord if you do not use this device for a long time.
3. Do not expose the speakers to any dripping or splashing and make sure no object filled with liquids, such as vases, etc., are placed on them.

USB Operation

• This unit can support MP3/WAV/WMA/FLAC.

Specification

• Power source: 100-240V~50/60Hz, 20W

ErP Mode (ECO Mode)

Power on

• Long press Power/Source/Volume and Tone/Bluetooth Button together for 5S to turn on or turn off ErP mode(Eco mode).

Connecting the Speakers

Connecting the SP-HF800BT Speakers

1. Place the speakers next to the monitor, one on either side.
2. Plug the satellite speaker cables (A) into the host speaker’s “SPEAKER OUT” RCA jacks.
3. Plug the AC power cord (B) into a standard household electrical outlet.
4. Insert the 3.5mm plug of the audio cable (C) into the sound card and other audio source.

Control Function

1. Power/Source/Volume:
2. Press 2 seconds to turn on/off the system power.
3. Short press to switch Bluetooth/USB/Aux in mode.
4. Turn the Volume button to control the volume level.
5. Long press for 10 seconds to restore factory settings and return to the Bluetooth mode, when the speaker power on in AUX mode.
6. Tone/Bluetooth: Control the sound response and Bluetooth pairing.
7. Short press to switch Play/Pause in Bluetooth/USB mode.
8. Double press to go to the next songs in Bluetooth/ USB mode.
9. Triple press to go to the previous songs in Bluetooth/ USB mode.
10. Turn the Tone button to control the sound response level.
11. Headphone Jack: Accepts a headphone cable.

FCC STATEMENT

Federal Communication Commission(FCC) interference statement:

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure statement:

The transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a Minimum distance of 20cm between the radiator and any part of your body.

Disclaimer

The following does not apply to any country where such provisions are inconsistent with local law: KYE Systems Corp. makes no warranties with respect to this documentation, whether expressed or implied. All material is provided “as is”. This includes, but is not limited to, any implied warranties of merchantability and fitness is for a particular purpose. The information covered in this document is subject to change without notice.

KYE Systems Corp. assumes no responsibility for any errors that may appear in this document. All brand names mentioned in this manual are trademarks or registered trademarks of their respective companies.

Contact

KYE Systems Corp.

• No. 492, Sec. 5, Chongxin Rd., Sanchong Dist., New Taipei City 241017, Taiwan
• Tel: 886-2-2995-6645
• Fax: 886-2-2995-6649
• Email: support@geniusnet.com (Tech. Support)
• http://www.geniusnet.com

Copyright KYE Systems Corp. All rights reserved.

For actual items, refer to the physical goods contained herein.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>