Kalado KPF01 Wifi Automatic Feeder User Manual
- June 6, 2024
- Kalado
Table of Contents
Wi-Fi Automatic Feeder User Manual
KPF01
Safety information
WARNING!
- Do NOT use wet, canned, or moist food.
- Do NOT use outdoors. For indoor household use only.
- Do NOT allow small children to play with, in, or around pet feeders.
- Do NOT place anything on top of the pet feeder. The unit starts automatically. Keep clear.
- The base unit should NOT be submerged in water at any time, as this may damage electronic components.
- Always unplug any appliance when not in use, before putting on or taking off parts, and before cleaning.
- Do NOT pull on the electrical power cord to remove the plug from the wall outlet.
- To avoid tripping, always position the power cord out of the way of foot traffic.
- The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition.
- Do NOT modify the pet feeder.
- Do NOT place or store an appliance where it can fall or be pulled into a tub or sink.
- Only use attachments recommended or sold by the manufacturer.
- To reduce the risk of injury, close supervision is necessary when any appliance is used by or near children.
- If the plug of this device gets wet, turn off the electricity to that wall outlet. Do not attempt to unplug.
- To protect against electric shock, if using a power cord do not place the power cord or plug in water or other liquids.
- Dispose of all packaging materials properly. Some items may be packed in polybags; these bags could cause suffocation; keep away from children and pets.
NOTICE!
- Do not allow pets to chew on or swallow any parts.
- Intended for use with dogs or cats only.
- Do NOT place any foreign object in the pet feeder.
- For dry food use only.
- Pet feeder should be placed on a level surface.
Warranty
- We provide 12 months limited warranty.
- Timely customer service via: pet_support@kaladotech.com
Product Structure
What’s in the box?
1 x WiFi Automatic Feeder
1 x 5V/1A Power Adapter
1 x Desiccant Bag
1 x User Manual
1. Stainless Steel Bowl
2. Lid Latch
3. Food Tank
4. Feeder Base| 5. Food Outlet
6. Battery Compartment
7. Food Tray
8. Unlock Light| 9. Wi-Fi Light
10. Fault Light
11. Unlock Button
12. Manual Feeding Button
---|---|---
Feeder Installation and Clean
-
Power supply connection.
• Step 1. Open the battery compartment at the bottom of the feeder.
• Step 2. Insert the power adapter cord into the “Power Adapter Interface”, wind the excess power cord as needed and then exit at the “Outlet”.
Warm Tips:
1. Use 3 PCS alkaline D batteries(NOT included) to power. Do NOT use rechargeable batteries.
2. Batteries are for backup power only and should not be used as the main power source.
-
Automatic feeder assembly.
Tilt up the feeder (feeder base and food tank), close the side with the “ears” of the food tray to the gap of the feeder, put down the feeder, and press down on the food tray.
-
Add food to the food tank.
- Open the lid of the food tank: press the button on the back of the food bank, and at the same time lift the lid up.
- Loosen the button on the other side to remove the lid.
- Place the Desiccant bag into the buckle of Lid.
- Close the food tank in the reverse order of removing the food tank
lid.
- Connect the power adapter to work
- Remove and clean the food tank.
Step 1. Unplug the power adapter from the power outlet.
Step 2. Remove the food tank: rotate the food tank counterclockwise and lift it up.
Step 3. Remove the allocated food funnel: turn the
food tank over, grab the allocated food funnel, rotate the allocated food
funnel counterclockwise, and extract it from the top.
App Quickly Setting Guide
Step l. Download the Osaio App
Please search ” Osaio ” on Google Play /App Store, or scan the QR code to
download the App.
https://download.osaio.net/app
Step 2. Ensure the feeder is waiting to be paired
Long press the unlock button and the manual feeding button at the same time
until the Wi-Fi indicator light blinks.
Step 3. Turn on Bluetooth and connect your phone to 2.4GHz Wi-Fi
Step 4. log in to Osaio App and click “+” to add your automatic feeder
Step 5. Follow the instruction on the App to finish the steps of
connection
LED Indicator
| LED Indicator & Button operation | Status |
|---|
Reset tip: Press the unlock button and the manual feeding button at the same
time until the Wi-Fi light blinks Slowly| Ready for connection
Rapid blinking Wi-Fi light| Connection is in progress
Solid Wi-Fi light| Connected successfully
Solid fault light| There is not enough food in the food tank. It will go out
automatically after adding food
Long press the unlock button until the unlock light turn on| Unlocking status.
Manual feeding button available
Warm Tips: In the unlocked state, the unlock indicator is on. One minute after unlocking, it will automatically enter the locked state, and then the unlock light will go out.
Wi-Fi Setup Troubleshooting
Unable to get my feeder connected, or appears disconnected from Wi-Fi.
- Ensure your home Wi-Fi is working properly and your phone is connected to it.
- The feeder supports 2.4GHz Wi-Fi only. Make sure you are in a 2.4GHz Wi-Fi circumstance and ensure the Wi-Fi signal is good.
- Weak disconnection, place your feeder near your router during the initial setup.
- Reset the feeder: long-press the unlock button and the feeding button at the same time until the Wi-Fi light blinks to set up the connection again.
- The feeder supports Bluetooth automatic connection. Make sure Bluetooth is opened on your phone and connected to Wi-Fi. After resetting the feeder, open the App and click add device, the feeder will be found, and follow the instructions to continue connecting.
- If still fails to connect, please contact our after-sales support team via: pet_support@kaladotech.com
Other Troubleshooting
The food won’t come out
- Please be sure to fill in with dry food. kibble size should range from 2-20mm / 0.07-0.787in in diameter.
- Check whether any foreign objects are placed.
- Check whether it’s a low battery level if the power adapter is not connected.
I can’t disassemble the food tank
Please follow the steps in Feeder Installation and Clean on page 5.
The portion size is not exact
The first few portions may vary, and it doesn’t mean faulty equipment. After
about 6 feedings, it should be almost the same.
FCC-Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However; there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device is to comply with Class B limits.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Statement
To maintain compliance with FCC’s RF exposure guidelines, This equipment
should be installed and operated with a minimum distance of 20cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
Made in China
Version 1.0