ELNUR GABARRON CCN-2000 Wall Mounted Downflow Ceramic Heater User Guide

ELNUR GABARRON CCN-2000 Wall Mounted Downflow Ceramic Heater

SAFETY ADVICE

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

CAUTION
Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

CAUTION
In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

WARNING
In order to avoid overheating, do not cover the heater.

• The heater must not be located immediately below a socket-outlet.
• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• Fixed heaters are to be installed so that switches and other controls cannot be touched by a person in the bath or shower.
• Means for disconnection having a contact separation in all poles must be incorporated in the fixed wiring in accordance with the wiring rules.
• THIS PRODUCT IS FOR ROOM HEATING

INSTALLATION

1. Drill holes on the wall according to the instruction inside the box.
2. Be sure to keep the safety distances as shown on the above drawing.
3. Fit the fasten tube in the hole and fit the bracket on the wall with screws.
4. Hang the unit on the bracket gently, after ensuring the unit is right fixed  turn the lock in the bracket as picture show.
5. Before using the heater, make sure it’s mounted tightly on the wall.

CONTROL PANEL

1. Standby indicator
2. Heating status indicator
3. Comfort mode indicator
4. ECO mode indicator

REMOTE CONTROL

1. Standby
2. Mode Selection
3. Power Setting
4. Timer
5. Increase function
6. Decrease function

Power setting to choose H0 for fan mode, H1 for half power 1000W and H2 for full power 2000W.

HOW TO USE

• Plug the appliance to AC 220-240V 50Hz socket and press on/off switch with a beep sound. The indicator light is on.
• Press to turn on the heater.
• To stop the heater working press to turn off the heater,
• Unplug the product when it’s not in use.

Temperature Setting

When the screen display the target set temperature press and to set directly Comfort mode in P1/P2/P3 press and to set the temperature from 10-35ºC. ECO mode in P1/P2/P3 Press and to set the temperature from 6ºC-31ºC.
Note ECO mode=Comfort mode – 4ºC

Clock and Day of Week Setting

• Press down  3 secs to enter clock and day of week setting.
• The screen display press  and to select the day from 1-7.

• Press to confirm day setting and enter the clock hour setting with the screen display.
• Press and  to set the current hour.
• Press to confirm hour setting and enter the minute setting  with the screen display.
• Press and to set the current minute.
• Press to confirm all settings.
  Note The clock and calendar will be reset to factory default if without power supply.

Heating Mode

• Press to enter mode selection. By pressing heating mode runs in a continuous cycle as below:

• Comfort mode Press up and down to set the temperature from 10ºC – 35ºC.

• ECO mode Press and to set the temperature from 6ºC – 31ºC.
  Note ECO mode=Comfort mode -4ºC.

• Anti-frost mode: the screen display.

• The target temperature is 7ºC. The temperature can’t be adjusted.

• P1/P2/P3: Pre-set heating program.

• Note If the clock and day setting are not finished, the first time to enter P1/P2/P3 program setting, it is requested to set day and clock setting in advance

P1(Monday-Sunday) Program can’t be set.

P2(Monday-Friday) Program can’t be set.

P2(Saturday-Sunday) Program can’t be set.

P3(Monday-Friday) Adjustable program.

P3:(Saturday-Sunday) Adjustable program.

P3 Adjustable Program Setting

1. When under P3 mode press M over 3 secs to enter day setting.
2. The screen displays  press up and down to set from Monday-Sunday press to confirm and enter hour setting
3. The screen displays press up and down to set from 00-23.
4. Press M to choose heating mode for every hour Comfort mode or ECO mode or 2 lights off for anti frost mode
5. Repeat the operation until you have completed the schedule of every hour and every day.
6. After setting heating mode for hour 23 press up down to come back to day setting  when screen displays press finish all setting with display of .

Power Setting

The power can only be set in remote control to set half power or full power.

Timer off Function

Press one time the screen display 0 h  and keeps flashing keep pressing clock the screen will display 2h – 4h – 8h. Or press up and down to set timer from 0-9 hours.

Open Window Function

• To turn on open window function, press together M and up the screen will display after 3 seconds the screen will display the set temperature.
• To turn off open window function press together M and down the screen will display  after 3 seconds the screen will display the set temperature.

CLEANING & MAINTENANCE

• Switch off and unplug from the power supply before cleaning.
• Using a soft moist cloth, with or without a mild soap solution carefully clean the exterior surface of the product.
• Allow the product to completely cool before handling or cleaning it.
• Do not allow water or other liquids to run into the interior of the product, as this could create a fire and electrical hazard.
• We also recommend the periodic cleaning of this appliance by lightly running a vacuum cleaner nozzle over the guards to remove any dust or dirt that may have

CAUTION do not use harsh detergents, chemical cleaners or solvents as they may damage the surface finish of the plastics components

• This marking indicates that this product should not be disposed with other household wastes throughout the EU.
• To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources.
• To return your used device  please use the return and collection systems or contact the retailer where the product was purchased.
• They can take this product for environmental safe recycling this product contains a remote control including a Lithium button battery. Before returning the device to the recycling point the user should remove the battery and put it in the selective collection point for these wastes.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>