ELNUR GABARRON CP-TURBO Portable Convector Heater User Guide

ELNUR GABARRON CP-TURBO Portable Convector Heater

Product Information

• Model: CP-TURBO
• Power: 2000 W (2 levels – 1250 / 2000 W)
• Dimensions: 62.0 cm (length) x 26.0 cm (width) x 38.5 cm (height)
• Weight: 3.6 kg
• Voltage: 220 – 240 V
• Class: I
• Thermostat Control: Yes
• Slide switch for activation
• Timer function

Product Usage Instructions

1. Before connecting the appliance for the first time, read the instructions carefully.
2. Assembly of the convector:
   • Follow the provided instructions to assemble the convector.
3. Operation:
   • Use the thermostat control to adjust the desired temperature.
   • Activate the convector by sliding the switch.
   • Set the timer function if required.
4. Maintenance and Cleaning:
   • Refer to the maintenance and cleaning instructions in the user manual for proper care of the product.

INSTALLATION INSTRUCTIONS

WARNING Please read these instructions before installing or using this appliance for the first time.

• The warranty of the heater will not cover any damage caused by non-observance of any of these instructions. The instructions should be retained for future reference. This guide must be kept and given to any new owner.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance must not be made by children without supervision.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• Children of less than 3 years should be kept away unless continuously supervised.
• Please check that the voltage in the rating label fits the power supply.
• The use of panel heaters is forbidden in any area where there is a presence of gases, explosives or inflammable objects.
• Do not use this heater to dry clothes. Do not cover this heater or put objects in contact with it.
• Neither the connecting cable nor any other object must come into contact with the hot unit.
• Do not cover this heater at any time.
• The air outlet at the top of the thermal radiator and the air inlet at the bottom are provided to ensure the most efficient operation of the appliance. They also protect the heater from overheating; therefore, it is essential that at no time are they covered.
• This heater should be switched off at the isolating switch before any repair work is carried out.
• The heater should not be used just below an electrical socket.
• The appliance must be used in such a way that it is impossible for anyone using a bath or shower, to touch the controls.
• The heater is fitted with a flexible cable size 3 x 1.00 mm² for electrical connection. It may be used to connect the heater to the fixed wiring of the premised through a suitable connection box positioned adjacent to the heater.
• If the flexible power cable for this unit is damaged, it may only be replaced by a repair workshop recognised by the manufacturer, as special tools are necessary.
• This appliance must be earthed.
• All models are supplied with an electrical interrupt cut-out. This will switch off the heater if, for any reason, it overheats. Should the cut-out operate, turn the heater off and remove the cause for the overheating. The cut-out will be reset automatically.
• The presence of air particles of smoke, dust and other pollutants could, in time, discolour the walls and surfaces around the heater.
• CAUTION — Some parts of this product can become very hot and cause burns. Particular attention must be given when children and vulnerable people are present.
• This appliance is a portable heater. Do not use the heater unless the feet are correctly attached.
• Do not use outdoors.
• Do not place the heater on carpets having a very deep pile.
• Always ensure that the heater is placed on a firm level surface. Ensure that the heater is not positioned close to curtains or furniture as this could represent a fire hazard.
• Always unplug the heater when moving it from one location to another.
• Do not use this heater with a programmer, timer or any other device that switches the heater on automatically, since a fire hazard exists if the heater is covered or positioned incorrectly.

WARNING: In order to avoid overheating do not cover the heater.

ASSEMBLY OF THE HEATER

Before using the heater, the feet (supplied separately in the carton), must be fitted to the unit. These are to be attached to the base of the heater using the 4 self-tapping screws provided, taking care to ensure that they are located correctly in the bottom ends of the heater side moldings.

USING THE HEATER

Choose a suitable location for the heater, taking into account the safety instructions above.
Insert the plug of the heater into a suitable socket (230V/50Hz).
Turn the thermostat knob fully in a clockwise direction to the maximum setting.
Turn on the power by means of the thermostat switch on the side panel. When the power is on, the power indicator will light up. Then turn on the heating function by means of the function selector switch “I” on the side panel. For maximum heat output the selector switch should be turned to the most highgrade “II”. When the desired room temperature has been reached, the thermostat knob should be turned slowly anti-clockwise until the thermostat is heard to click off and the lights on the element switches are seen to go out.

After this the heater will keep the air temperature in the room at the set temperature by switching on and off automatically.

Convector heater with fan (Turbo for fast-heating)

When the selector switch is turned to the low-speed position, there is an air outlet on the side panel, the heating lowgrade also turn on the fan. For maximum heat output the selector switch should be turned to the most high- speed the heating high-speed also turn on the fan.

Convector heater with Timer
This model is also fitted with a 24hr timer which has 96 segments around its circumference, each segment being equivalent to 15 minutes of time. With the aid of this timer it is possible to preset the time and duration of the period(s) that it is desired the heater will operate, in any 24hr period.

Timer Operation
The centre of the timer has a 3-position slide switch.
In the central position (denoted by the clock symbol) the timer will switch the heater on and off at times set by the segments, (see setting the timer, below).
The position denoted by the “I”, is a timer override position. The timer will continue to run but power will be fed continuously to the heater. This enables the heater to be on all the time if required.

In the position denoted by the “O”, the timer continues to run but no power is fed to the heater.

Setting the Timer

Ensure the slide switch on the timer is at the mid position next to the clock symbol.
Rotate the outer ring of the timer in a clockwise direction until the current time is lined up with the arrow pointer, i.e. if the time the timer is being set is 8 p.m., rotate the outer ring until the number 20 is in line with the arrow pointer.
Set the time the heater is required to run by pulling the segments around the outer ring forward appropriate to the running period(s) required.
When set, the heater will operate each day during the times programmed. Note, the heater must always be plugged into a power socket, the element switches must be in the on position and the thermostat must be suitably set to ensure the heater will come on.
If the heater is required to run continuously the slide switch on the timer should be set to the “I” position.
If it is subsequently required to revert back to timer operation, the slide switch on the timer should be set to the central (clock) position.
When using in timer mode, due consideration should be given to the fact that the heater may come on whilst unattended.

CLEANING AND MAINTENANCE

• The panel heaters do not precise any special maintenance providing thermal comfort during large periods.
• Always un-plug the heater from the wall socket and allow it to cool down before cleaning.
• Clean dust with a dry, soft cloth only when the unit is disconnected and cold.
• Do not use solvents or abrasive products for cleaning.
• When the heater is not used for long periods of time it should be protected from dust and stored in a clean dry place.
• This panel heater has been manufactured under an assured quality system using environment friendly processes.
• Please take the panel heaters to a clean point once their useful life is finished, in order to recycle their materials in the right way.

SPECIFICATIONS

PRODUCT FICHE

CP – TURBO
Heat Output
Nominal heat output| Pnom| 2,0| kW
Minimum heat output| Pmin| 1,25| kW
Maximum continuous heat output| Pmax,c| 2,0| kW
Auxiliary electricity consumption
At nominal heat output| elmax| 0,000| kW
At minimum heat output| elmin| 0,000| kW
In standby mode| elSB| <0,0005| kW
Item| Value
---|---
Type of heat output / room temperature control
With mechanic thermostat room temperature control| Yes

Commission Regulation (UE) 2015/1188 of 28 April 2015. Ecodesign requirements for electric portable local space heater.

The symbol on the product or in its packaging indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this

product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. These instructions are only valid in the EU member states.

ELNUR S.A.
Travesía de Villa Esther, 11
28110 Algete – Madrid

Tfno. Atención al Cliente:
+34 91 628 1440
www.elnurgabarron.es
www.elnurgabarron.com
www.elnur.co.uk

As a part of the policy of continuous product improvement Elnur, s.a. reserves the right to alter specifications without notice.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>