camry CR 7724 Convection Heater LCD with Remote Control User Manual

: June 5, 2024
: camry

Table of Contents

GUIDELINES FOR SAFETY OF USE
CLEANING AND MAINTENANCE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

camry CR 7724 Convection Heater LCD with Remote
Control CR 7724

This product is suitable only for occasional use or for use in well-insulated rooms.

Model identifier CR7724| |
---|---|---
Item| __**Symbol| | | | Item| Unit
Heat output| | | Type of heat input, for electric storage local space heaters only (select one)
Nominal heat output| **

P nom

| ****

2,15

| ****

kW

| | manual heat charge control, with integrated thermostat| ** [no]
Minimum heat output (indicative)| **

P min

| ****

0,01372

| ****

kW

| | manual heat charge control with room and /or outdoor temperature feedback

| ** [no]
Maximum continuous heat output| **

Pmax,c

| ****

2,15

| ****

kW

kW

| | two or more manual stages, no room temperature control| [no]
| | | with mechanic thermostat room temperature control| [no]
| | | with electronic room temperature control| [yes]
| | | electronic room temperature control plus day timer| [no]
| | | electronic room temperature control plus week timer| [no]
| | | Other control options (multiple selections possible)
| | | room temperature control, with presence detection| ** [no]
| | | room temperature control, with open window detection| ** [no]
| | | with distance control option| [no]
| | | with adaptive start control| [no]
| | | with working time limitation| [no]
| | | with black bulb sensor| [no]
Contact| Adler Sp. z o.o. ul. Ordona 2A, 01-237 Warszawa, Polska

camry CR 7724 Convection Heater LCD with Remote Control -
Fig

ATTENTION:
The device is intended for domestic use only.
The device is NOT intended for commercial/professional use.
The device is NOT suitable for use outdoors.
Attention! Before use, it is essential that you read these operating instructions to avoid accidents and for the correct use of the device. Keep this manual and keep it so that you
can easily use it.

GUIDELINES FOR SAFETY OF USE

Before use, check that the voltage specified on the nameplate corresponds to the local parameters of salinity, but remember that the marking: AC- is alternating current and DC is DC.
Connect the device only to a 220-240V ~ 50/60 Hz grounded outlet.
Before use, unroll and straighten the power cord
Make sure that the power cord and plug have no visible damage
Before and during use, make sure that the power cord is not stretched over an open flame or another source of heat and has sharp edges that can damage the insulation of the cable.
Before first use, remove all packaging components. Attention! In the case of a casing with metal parts, on these elements, a slightly visible protective foil can be stretched, which should also be removed.
The device should not be used by children, or persons with limited physical, sensory or mental capacity without the supervision of authorized or experienced persons and always in accordance with these instructions.
The equipment is not intended for use with external time switches or a separate remote control system.
WARNING: This equipment may be used by children over 8 years of age and persons with limited physical, sensory or mental ability, or persons who have no experience or knowledge of equipment, ONLY if this is done under the supervision of a person responsible for their safety or have been given instructions about the safe use of the device and are aware of the dangers associated with its use. Children should not play with the equipment. Cleaning and maintenance of the device should not be performed by children unless they are over 8 years of age and are supervised
Do not leave the device unattended during operation.
Do not immerse the appliance and the power cord in water or any other liquids.
When the device is not in use, it should always be disconnected from the power outlet.
When pulling the plug from the socket, never pull the power cord by the plug only.
Do put NO METAL ITEMS inside the device
The manufacturer is not liable for damages resulting from improper use of the device.
It should be remembered that some parts of the device and the cabinet during work get very hot, so be careful and do not touch them, you can get burned.
NEVER cover the device during operation or when it does not cool down completely
Remember that the heating elements of the device take time to cool down completely.
When using the device, ensure adequate space above and around. The device must not touch any easily flammable objects during work, such as decorations, paper towels, curtains, clothing, etc.
The heater installed in the bathroom should be installed so that connectors and other regulators can not be touched by a person in the bathtub or under the shower.
In heaters for high-altitude fixtures, the positions of the different positions of the connectors should be visible from a distance of 1 m
The labeling for covering the heater should be visible after installing the heater
You cannot place the device near flammable materials such as curtains, etc. Keep 1 m distance from furniture, walls, or other objects.
The device can not be used with external time switches or other separate remote control systems
Do not expose the device to atmospheric conditions (rain, sun, etc.) or use it in conditions of high humidity (bathrooms, damp camping houses)
Periodically check the condition of the power cord. If the power cord is damaged, it should be replaced by a specialist repair facility in order to avoid a hazard
Do not use the device near flammable materials
Do not use this heater in the immediate vicinity of a bathtub, shower, or swimming pool
Do not use this heater if it has been dropped
Do not use it if there are visible signs of damage to the heater
Use the heater on a level and stable surface or attach it to the wall, if provided for by the manufacturer

WARNING: Do not use this heater in small rooms where there are people who are unable to leave them by themselves unless constant supervision is ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains, or other flammable materials at least 1 m away from the heater air outlet.

It is recommended that the electrical installation be equipped with an automatic residual current circuit breaker with a 30mA starting current for increased safety.
Note: If the power cord or power plug is damaged, it should always be replaced or repaired by a specialized repair shop.

II. WARNINGS

Never use the device if it is damaged or does not function properly.
Never use the device if it has fallen from a height before and shows visible signs of damage.
Do not use extension cords or other electrical outlets that do not meet the applicable standards and electrical regulations.
Any repairs, dismantling or replacement of any parts should always be made by a specialized facility.
If the device and elements such as electrical contacts are wet, the plug or cable should be dried before using the device and its components.
Do not use the device with wet hands.
When there is a risk that the device has been damaged NEVER try to repair the device yourself.
Never wash the device under running water or in such a way that water drips into it.
Do not use accessories that are not recommended by the manufacturer. They may pose a danger to the user and may cause damage to the device.
Ensure that the device has cooled down before storing.
Do not touch the housing during use. During operation, use only knobs and switches. After switching off, wait for the device to cool down.
CAUTION: Some parts of this device may become very hot during operation and cause burns.

III. BEFORE FIRST USE

Remove all packing material and straighten the power cord
During installation, in no case may the device be covered with insulating material or similar material
When assembling the device, beams and rafters should not be cut cut
Before first use read all instructions for use.
Check if the voltage listed on the product rating label corresponds to the voltage of the power network in your home
Do not use the device unless the feet are correctly attached
Keep the mains lead away from the hot body of the device.
The device is not intended for use in bathrooms, laundry areas, or similar indoor locations. Never place the device where it may fall into a
bathtub or another water container.
Do not use outdoors.
Do not place any objects close to the outlet grills or the air intake openings of the device when operating.
Do not place the device on carpets having very high hair.
Always ensure that the device is placed on a firm level surface. Ensure that the device is not positioned close to curtains or furniture as this could create a fire hazard.
Do not position the device in front of, or immediately below, a wall socket.
Do not position the under the window.
Do not insert any object through the heater outlet or air intake grills of the device.
Do not use the device in areas where flammable liquids are stored or where flammable fumes may be present.
Always unplug the device when moving it from one location to another.

INSTALLATION IN STANDING POSITION ON THE FLOOR
Before using the device, the feet (supplied separately in the carton), must be fitted to the device. These are to the base of the heater using the 4 self- tapping screws provided. Take your care to ensure that they are located correctly in the bottom ends of the device side moldings.

PRODUCT DESCRIPTION: CONVECTION HEATER WITH REMOTE CONTROL

1. Power switch
4. Feet
7. Remote control| 2. Air outlet grid
5. Housing
8. Fan’s ventilation grid| 3. Air inlet grid
6. Control Panel LCD
9. Compartment for remote control
---|---|---
CONTROL PANEL
A. Power button
C. TURBO FAN button
E. Temperature unit button
G. Temperature decrease button
I. TURBO FAN indicator
K. Room temperature indicator| B. Heat output button
D. Timer button 1-24 hours
F. Temperature increase button
H. Frost protection indicator
J. Selected temperature indicator
L. Time remaining indicator to turn off the device
---|---

The remote control (7) operation way is the same as the buttons on the control panel (6).

USAGE

Turn on the device by pressing by hand the power switch (1) on the left side of the device.
Press the power button (A) to illuminate the control panel (6), the device is ready to operate now.
To set the heat output press the heat output button (B) the appropriate number of times, and the required heat level setting is achieved:
– time pressing means low heat setting – 1000W heat output, it will be shown on the control panel,
– two times pressing means middle heat setting – 1300W heat output, the value will be shown on the control panel,
– three times pressing means high heat setting – 2300W heat output, the value will be shown on the control panel,
– four times pressing means the device comes into frost protection function, snowflake indicator (H) will be shown on the control panel. The frost-proof mode is turned on, 5° C / 41 ° F is a fixed temperature value, when the environment temperature is below 5° C / 41 ° F, the device will start heat mode automatically.
To switch the TURBO fan on, press the button (C), and the fan indicator (I) will be illuminated. The fan starts to operate. To stop the fan press the button (C) again.
To set the period of time the device will switch off you can use the timer function. To preset a switch-off time press the timer button (D) an appropriate number of times to choose an operation time between 1-24 hours. The device will switch off automatically after the chosen period of time.
To set the temperature units (F/C) which means: F = Fahrenheit and C = Centigrade press the temperature units button (E) the appropriate number of times until the required temperature unit setting is achieved.
To increase the temperature setting press the button (F) the appropriate number of times until the required increased temperature setting is achieved. The selected temperature setting (J) is indicated on the control panel. The range of temperature is 5-37°C / 41-99°F.
To decrease the temperature setting press the button (G) the appropriate number of times until the required decreased temperature setting is achieved. The selected temperature setting (J) is indicated on the control panel.
Note: the control panel (6) always shows the last set temperature (J) and presents the room temperature (K). If the heat function switches itself off then set temperature (J) had been achieved in the immediate area of the device.
To switch off the device press the power button (A) and next switch off the power switch (1).
After around 1 minute of the last action, the control panel (6) stops illuminating but the device is operating according to the last setting.

CLEANING AND MAINTENANCE

Always unplug the appliance from the power socket before cleaning.
If during cleaning items such as the power plug, thermostat, electrical contacts, etc. are soaked before being used again, they should be thoroughly dried.
Do not use aggressive detergents in the form of emulsions, lotions, pastes, etc. to clean the cabinet. They can, among other things, remove the information graphic symbols, such as signs, warning signs, etc.
Ensure that the device has cooled down before cleaning.
When the device is not used for long periods of time, it should be protected against dust and stored in a clean dry place.

TECHNICAL DATA:
Voltage: 220-240V ~50/60Hz
Power: 2000-2300W
Max. Power: 2300W
IPX 0

****| “Caution Hot Surface” – The temperature of available surfaces may be higher when the equipment is working, which means that the housing elements become very hot during operation, SAVE CAREFUL !!!
---|---
| DO NOT COVER« INSCRIPTION IMPORTANCE
The inscription on the device means that the device is not to be covered with clothing, blankets, and other textile products that could cause ignition.
| WARNING: Do not use this equipment near bathtubs, showers, swimming pools, and similar water tanks.
| To protect your environment: please separate carton boxes and plastic bags and dispose of them in corresponding waste bins.
The used appliances should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose of this appliance in the common waste bin.

www.camryhome.eu