KLARSTEIN 156308624 ARTIKELNAME Ice Cube Maker Instruction Manual

ARTIKELNAME
Ice Cube Maker
Artikelnummer
****www.klarstein.com

Dear Customer,
Congratulations on purchasing this equipment. Please read this manual carefully and take care of the following hints to avoid damage. Any failure caused by ignoring the items and cautions mentioned in the instruction manual is not covered by our warranty and any liability. Scan the QR code to get access to the latest user manual and other  information about the product

https://use.berlin/10033109

TECHNICAL DATA

MANUFACTURER & IMPORTER (UK)

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom

SAFETY INSTRUCTIONS

• Check that the mains voltage corresponds to the rating of the appliance before operating.
• Use handles or knobs when moving. Place on a flat stable surface for use. Do not use outdoors.
• Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.
• Unplug from socket outlet when not in use.
• To protect against electric shock, do not immerse the cord or plug in water or any other liquid.
• The use of accessory attachments not recommended by the appliance manufacturer may cause injury.
• Do not locate this appliance immediately below a socket outlet.
• Do not allow the cord to overhang the countertop where it can be easily pulled by children.
• Do not use this appliance for anything else other than its intended use.
• Do not overfill as this may cause a hazard. Ensure the lid is closed when in operation
• To remove the plug from the outlet, do not pull on supply cord. Grasp the plug firmly and pull to remove it.
• No liability can be accepted for any damage caused by noncompliance with these instructions or any other improper use or mishandling. This appliance is for household use only
• This appliance is not intended to be operated by means of an external timer or separate remote control system.
• This appliance is not intended to be immersed in water.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• Please according to local regulations regarding disposal of the appliance for its flammable blowing gas.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• Fill with potable water only.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

INSTALLATION

• After unpacking, carefully check the machine for damage during transport, then remove the accessory, and wipe the ice bucket with a clean damp cloth.
• This series of machines should be placed in the air circulation of clean places, not open to the ground, should not be exposed to direct sunlight and rain, and can not be placed near the heat source.
• The ambient temperature of this series of machines should be no less than 3°C, not higher than 40°C, around the appropriate spacing should be retained to maximize the efficiency of ice and machine cooling.

•  When installing the ice machine, please check the front and rear directions level.
• This series of machines is strictly prohibited to place the ice below the freezing point of ice, otherwise, it will produce serious failure.

Installation of Power

• The power supply should be the same as that on the machine nameplate (220 V / 50 Hz or 380 V / 50 Hz).
• The power plug should be plugged directly into a power outlet with a ground wire and not on a temporary terminal block. All lines must meet national or regional standards.
• The voltage fluctuation must not exceed ± 10% of the rated voltage, otherwise, the regulator should be installed.
• The grounding of this series must meet the electrical standard.

Installation of water systems

• The water supplied to the ice machine must meet the criteria for local drinking water.
• The water supplied to the ice machine must be connected to the filter in order to improve the drinking standards for water. Please do not directly connect to tap water, due to water quality caused by ice-making failure, I do not assume responsibility for maintenance.
• Drain interface, please connect the water pipe to the water into the water

BEFORE FIRST USE

• Check whether the ice machine is horizontal.
• Check whether the plug is plugged in, and the water pipe is connected correctly.
• Check whether the power supply is consistent with the machine nameplate.
• Check whether the ambient temperature and water temperature of the ice machine are within the indicated range.
• The automatic water supply device is normal, the water tank is reasonable water storage (the machine has been adjusted when the factory water level, the user may not make corrections)

CONTROL PANEL AND BUTTON FUNCTIONS

OPERATION

1. Plug in the power, click the ice machine key, and the ice maker starts running.

2. The supply electro valve will open and the water level float will float with water when the water reaches the required water level the supply electro valve will turn off,
   and the machine will start the cleaning process, cleaning is completed it enters the ice-making process automatically.

3. When the ice thickness reaches the set thickness, the ice-free program starts, the solenoid valve starts to work, the pump stops working, the heat enters the evaporator, and the ice falls in about 1.5 minutes. When the ice falls the dam-board will turn over and turn on the magnetic reed switch . When the magnetic reed switch is closed the machine will start the ice making again. When the reed switch is closed, the machine enters the ice-making process again.

4. The compressor will not stop during the ice-making and ice removing process.
   5. When the ice bucket is full of ice, the reed switch can not be automatically closed, the machine automatically stops working, when taking enough ice, the reed switch is eclosed, the delay after 3 minutes the machine starts, re-enter the ice process.

Ice thickness adjustment

1. Press and hold the (+) button for 3 seconds to enter the settings. When the temperature indicator flashes, use the (+) or (-) button to adjust the thickness of the ice. Then press the (+) button to display the number of minutes. Each time you press (+) again, the time is increased by 1 minute. The maximum time that can be set is 25 minutes in addition to the preset ice preparation time. The time is reduced by 1 minute each time the (-) button is pressed again. The maximum time that can be set is -9 minutes and is subtracted from the preset ice preparation time. Increase the time for thicker ice cubes and reduce it for thin ice cubes.
2. When the ice has been discarded and the new cycle starts, the values you have just set are automatically taken over.

Switching the light on/off
Press and hold the – button for 3 seconds to turn on the lights and press the button to turn off the lights again for 3 seconds.

Planned switch-on

1. In standby mode, press the TIMING button. „Timed“ lights up and the remaining time until power on is displayed in hours.
2. Press the +/ – buttons to adjust the remaining time until the power is turned on.
3. Press the TIMING button again to deactivate the scheduled power-on.

Scheduled shutdown

1. In ice-making mode, press the TIMING button. The „Timed“ display is illuminated and shows the remaining ice production time in hours.
2. Adjust the remaining time by pressing the +/ – buttons.
3. Press the TIMING button again to deactivate the automatic shutoff.

Full ice container

1. When the ice container is full, no additional ice can get in and the machine switches off automatically.
2. After the ice has been removed from the container, it takes 3 minutes for the machine to restart automatically.

Note: As a result of voltage and pressure fluctuations caused by the ice machine stops, the icefall can be delayed. Only after 5 minutes switch off the power supply and then test the machine. Due to changes in the water temperature and the ambient temperature, it may happen that ice cants in the container. Turn off the unit for 10 minutes and then turn it on again.

CLEANING AND CARE

Cleansing function

1. Press the CLEANING button for 3 seconds in standby mode. The unit switches to the cleaning mode, the water valve opens, the water level rises to the required level, the pump opens. The cleaning time is 30 minutes, the time flashes on the screen. After cleaning is completed, the water valve opens again to ensure the required water level. The device then returns to standby mode.
2. During the ice-making process, the machine goes through 10 cycles before cleaning for 20 seconds (the cleaning interval may vary on some models).

Cleaning the surfaces of the unit

1. Clean the unit with a soft cloth and a neutral soap solution. Then rub it dry with a soft cloth.
2. Stubborn stains can be removed with stainless steel wool. Do not use conventional steel wool or sandpaper as this could scratch the surface of the unit.

Condenser maintenance

1. Clean the condenser regularly, otherwise, ice production will decrease and the unit may fail.
2. Clean the filter every 1-2 months with a neutral soapy water solution or detergent and remove dust accumulations.
3. Clean the heat sink of the condenser from top to bottom with a soft brush. Make sure that the heat sink is not bent.
4. If there is oil in the heat sink of the condenser, you can use a special cleaning agent.
5. The condenser should be replaced at least every six months and replace all components correctly after cleaning.

Note: Make sure that the water supply is interrupted during cleaning and that the unit is disconnected from the power supply.

Cleaning and disinfection of the ice container
Clean and disinfect the evaporator, ice grid, ice container, and other equipment components regularly to ensure that your equipment meets food requirements and standards.

TROUBLESHOOTING

1. fuses 2. power switch 3. cable 4. water switch 5. power plug 6. sockets
The ice tray baffle remains open.| If the ice tray baffle could open and close automatically
The machine stops 3 minutes after it’s turned on| High Voltage Protection| High-temperature environment
Dirty condenser filter
Damaged fon motor
The machine can only
make one tray of ice every time it is turned on| Ice full or ice troy baffle remains open| If the ice tray baffle could open and close automatically
Ice could not fall off the ice tray| Dirty Ice Troy| cleaning and disinfection need to be done
Machine not placed on a level ground| Adjust the machine to a level ground
The environment temperature is too low| Environment temperature should be higher 5°C
Faulty Solenoid valve| Replace the solenoid valve
Fault| Possible Cause| Check the following:
---|---|---
Ice too thin or not complete| Tank water level is too low| Check the water level and check if there is any leakage
Inlet valve does not work| Check the inlet valve
Not enough water pressure| Water pressure must be at 0.13-0.55 Mpa
Water pipes are blocked| Check the pipes and joints for dirt
Ice making is slow| Condenser is dirty| Clean the condenser
Temperature too high or the ventilation is bad| Ambient temperature should not exceed 40 , and ensure ventilation
The float ball in the tank is too high or there is leakage| Adjust the float ball or replace the water tank
Water tank leakage| Replace water tank
The Inlet valve could not be closed tightly or leakage| Clean or replace the inlet valve
Not enough space around the machine| Provide adequate space
Ice full indicator light is lit up but there is no ice| Faulty ice troy baffle| Check if the ice tray baffle is stuck

Error Codes

HINTS ON DISPOSAL

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

References

• Klarstein | Your home. Your kitchen. Your style.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>