AENO AEK0003 Electric Kettle EK3 User Manual
- June 5, 2024
- AENO
Table of Contents
AENO AEK0003 Electric Kettle EK3
AENO EK3 electric kettle is designed for boiling water at home and in the office.
Specifications
- Supply voltage: 220–240 V (AC);
- frequency: 50/60 Hz.
- Power: 1850–2200 W.
- Net Weight: 1.19 kg.
- Dimensions (L×W×H): 230 mm × 168 mm × 269 mm.
- Volume: 1.7 L.
- Power cord length: 0.8 m.
- Boiling water time: ≤6 min.
Package Contents
AENO smart kettle (See picture a), stand, quick start guide, warranty card.
Limitations and Warnings
Use the appliance only indoors at room temperature and no higher than 2000 m above sea level. Connect the kettle only to a grounded power outlet. Connect and operate the device only in accordance with its specifications. Do not disassemble or repair the unit on your own. Children and persons with disabilities may use the device only under the supervision of adults experienced in the use of the device. Do not allow children to play with the device. Make sure no liquid gets on the stand ❷ and the power button ❹ (See picture a). Do not immerse the device housing ❶, the stand ❷ and the power cord ❸ in water. Use the device only with the supplied stand. Do not plug the unit into an outlet if you notice damage of the housing, stand or power cord. If the device malfunctions, unplug it immediately. Install the device stand on a sturdy and stable surface, away from hot surfaces, bathtubs, showers, swimming pools and other potentially dangerous places. During use, the device housing heats up to a high temperature. Do not touch the housing with your hands, lift the device from the stand only by the handle ❺. Do not open the lid ❼ (See illustration b) during boiling water and the first 5 minutes after boiling. When pouring water out from the device immediately after boiling, do not bring your hand or other body parts close to the kettle spout ❽. Hot steam can burn the skin. Do not pour water below the “MIN” and above the “MAX” marks on the inside of the device.
Preparing for operation
Before the first use, fill the kettle to the “MAX” mark, boil and pour the water out.
Operating the device
Plug in the power cord ❸ located on the kettle stand ❷ (See picture c). To open the lid ❻ press the button ❼. Pour water ❶ into the kettle but do not exceed the “MAX” level. Turn on the switch ❹. The LED indicator on the switch will light up. After the water in the kettle boils, the device will turn off automatically. The LED indicator on the switch ❹ will go out. Remove the power cord plug from the power outlet when you finish using it.
Maintenance
Remove limescale on the inside of the kettle regularly. When using the kettle (3–5 times a day) it is recommended to descale it once a month if the water in your area is hard or very hard. If the water is soft or medium-hard, you can remove the scale once every 2–3 months. For descaling you can use 8 % vinegar or citric acid solution (30 g of citric acid per 0.5 L. of water). Pour 0.5 L. of vinegar or citric acid solution into the kettle and leave it for 2 hours without boiling. Then pour the contents of the kettle out and boil the water in it 4–5 times before the next use. The outer surface of the kettle can be cleaned with a dry cloth or a cloth dampened in a weak solution of neutral detergent. After applying the detergent, wipe the surface of the kettle with a clean, slightly dampened cloth and then wipe it dry. The stand can only be cleaned with a dry cloth. Never use abrasive cleaners, benzene, thinner, etc. to clean the kettle and the stand.
Troubleshooting
The device does not turn on. Possible cause: No AC mains voltage. Solution:
check if there is power by plugging in another device. There is voltage in the
mains, but the kettle does not turn on. Possible reason: lack of water in the
kettle or insufficient amount of water. Solution: Pour water into the kettle
above the “Min” mark on the inside of the device. There is voltage in the
mains and water in the kettle, but the device does not turn on. Possible
cause: a short circuit in the electrical circuitry of the device. Solution:
contact the service center.
WARNING! If your problem persists, please contact your local supplier or
the service center for support. Please do not disassemble the device or try to
repair it on your own.
Recycling information
The symbol indicates that you must follow the Waste Electrical and Electronic
Equipment (WEEE) and Waste Battery and Battery Regulations when disposing of
the device, its batteries and accumulators, and its electrical and electronic
accessories. According to the rules, this equipment must be disposed of
separately at the end of its service life. Do not dispose of the device, its
batteries and accumulators, or its electrical and electronic accessories
together with unsorted municipal
waste, as this will harm the environment. To dispose of this equipment, it
must be returned to the point of sale or turned
in to a local recycling facility. You should contact your local household
waste disposal service for details.
The warranty period and service life shall be 2 years as from the date of purchase of the device. Manufacturer: ASBISc Enterprises PLC, 43 Kolonakiou Street, Diamond Court, Ayios Athanasios, 4103 Limassol, Cyprus. Made in China. For current information and details on the device description and specification, as well as connection process, certificates, warranty and quality issues, see relevant Installation and Operation Manuals available for downloading at aeno.com/documents. All trademarks and names herein are the property of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>