PETLIBRO PLAF101 Wi-Fi Automatic Pet Feeder User Guide

: June 5, 2024
: PETLIBRO

Table of Contents

SAFETY PRECAUTIONS
PRODUCT DIAGRAM
CONTROLLING VIA APP
SET UP THE FEEDER
CLEANING & CARE
WARRANTY
WHAT’S IN THE BOX
SPECIFICATIONS
TROUBLESHOOTING
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PETLIBRO PLAF101 Wi-Fi Automatic Pet Feeder User Guide

SAFETY PRECAUTIONS

!WARNING

Dispose of all packaging materials properly. Some items may be packed in polybags; these bags could cause suffocation; keep away from children and pets.
Do NOT allow small children to play with, in or around the pet feeder.
To reduce the risk of injury, please keep close supervision when an appliance is used near children.
Do NOT use the feeder with pets not able to reach the food tray or with any physical disability.
Do NOT immerse the base part in water at any time as it may damage electronic components like the control panel.
Do NOT place any foreign object in the pet feeder.
Do NOT use outdoors. Check operation frequently to be sure the unit is dispensing properly.
Do NOT use wet, canned or moist food.
Do NOT disassemble the unit other than as instructed in this User Guide.
Do NOT use the feeder for anything other than its intended use.
Only use attachments recommended or sold by the manufacturer. The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition. Do not modify the pet feeder.
Do not operate any appliance if the unit is malfunctioning or has been damaged. Do not attempt repairs on the pet feeder yourself. Contact our customer service immediately for further instructions.
Always unplug when not in use and before cleaning.
Never pull on the electrical power cord to remove the plug from the wall outlet.
If the plug of this device gets wet, turn on electricity to that wall outlet. Do not attempt to unplug.
Examine the feeder after installation. Do not plug in if there is water on the power cord or plug.
To avoid tripping, always position power cord out of the way of foot traffic.

CAUTION

Do NOT allow pets to chew on or swallow any parts.
If an extension cord is necessary, one unit with a proper rating should be used.
Do NOT install or store the pet feeder where it will be exposed to weather or temperatures below -20 C / -4°F.
Use alkaline D batteries to power. Do NOT use rechargeable batteries.
Check the batteries regularly. Before leaving for extended time, always replace batteries with new ones.
Do NOT lift the pet feeder by lid, food tank, or food tray. Lift and carry it using both hands and the base, while keeping the unit in an upright position.
Suitable for dry food ONLY, with kibble size ranging from 2-10mm / 0.07-0.4in in diameter. Larger kibble may get stuck at the food outlet.
Read and observe all important notices listed on the pet feeder and in the packaging.

PRODUCT DIAGRAM

Front View

Bottom View

Desiccant Carrier
Lid
Lid Grip
Food Tank Buckle
Base
Food Outlet
Food Tray
Control Panel.
Food Tank
Battery Compartment
Speaker
Power Socket

LED Indicators

Blue| Flash every 0.5s| The Feeder is in Bluetooth or Nanual mode, ready to connect with App.
---|---|---
Slowly blink| The Feeder is in AP Mode, ready to connect with App.
Stay solid| Connected to WIFI and fully operational
Red| Off| Normal
Blink| Food dispensing system error ”Press and hold the Reset Button for 6s to reset
Stay for about 6s| Resetting WIFI connection

**Record Button

**

Press and hold the Record button, start recording after a beep is heard.
Record your voice for less than 10s. Release the button, 2 beeps will be heard indicating it’s saved.

**Reset Button

**

When the device is connected to the App, Press and hold the Reset Button for 6s to reset the device .
When the device is not connected to the App, Press and hold the Reset Button for 6s to switch between Manual Mode and AP Mode

**Feed Button

**

Press to manually feed a portion (appr. 2 1/2 tsp / 12.5m1)
Press and hold for 6s, the indicator will flash twice meaning the control panel is locked. Repeat to unlock.

CONTROLLING VIA APP

System Requirements

iPhone on iOS 9.0 or later; smartphone on Android 4.4 or later
Wireless router 2.4GHz (802.11 b/g/n)
High-speed internet connection

Before the Configuration

Please use indoor only to avoid direct exposure to the sunlight.
Please connect the Feeder via 2.4GHz only. If your WIFI is 5GHz only, set it to be compatible with 2.4GHz mode.
The WIFI password is composed of no more than 12 digits and letters. No special symbols are supported.
If the configuration fails, please power off and restart the feeder (press and hold the Reset button for 6s), then wait for about 2mins to re-configuration.

How the System Works

The Petlibro WIFI Automatic Feeder connects to your home’s wireless router and allows you to program and monitor your pet’s meals from anywhere, right from your smartphone with the Smart Life app. Use the app to schedule your pet’s meal times and portion sizes, view the last 7 days of feeder activity, and even dispense a meal remotely. Smartphone alerts let you know when your pet has been fed for added peace of mind. Delivering a convenient lifestyle to you and helping your pets become their best, the Petlibro WIFI Automatic Feeder keeps you connected to your pet’s feeding routine wherever you are!

Download the App & Log In

Scan the QR code or search for “Smart Life” on App Store or Google Play to download the App.
Sign up or Log in to your account.

Three Ways to Connect Your Feeder with APP

A. Configuring via Bluetooth Mode
Open App, select Home
To add the auto-pop-up
Feeder Connected, start page, Click +1″ Add device by entering WIFI to set the mealtimes Device”. account and password. and portion sizes.
B. Configuring via Manual Mode
- Add the device via “Pet Feeder” in Small Home Appliances.
C. Configuring via AP Mode
- Note: Please make sure the Bluetooth is turned off on your mobile before starting the AP mode connection.
- When the blue LED indicator flashes, press and hold the RET button for 6s until 3 beeps are heard. The LED indicator will turn to blink slowly. Now the feeder is under AP mode.
- Open the app on your mobile, tap Add Device —> Smart Feeder, tap the icon at the top right corner and select Configure WIFI via AP mode. Enter your WIFI name and password and go to the WIFI connection interface on your mobile, find the device “smartlife-xxxx” and tap to connect. Return to the app and wait for connecting.
  Note:
- Device name: WIFI Feeder
- Connect the Feeder via 2.4GHz only, if your WIFI is 5GHz, please set it to 2.4GHz before the connection.
- If it still fails connecting, please contact our Support Team.

Reset Feeder on App

Enter Setting on Control Center, Select Factory Reset.
3 beeps will be heard, wait for about 1 minute until. the blue light starts to flash slowly and your device is ready for re-connection.

Share Your Feeder

Enter Setting, select Share Device, add Sharing Via Smart Life Account Name.

Control Center on APP

SET UP THE FEEDER

Warning: Please use the original 5V power supply.

Assembling Food Tray
- Place the feeder in a desired location. Check the food tank is in place.
- Align the bulging of the food tray and holes in the base, and push upward to connect the two.
  Note: Before moving the feeder, please empty the tray, press it down to remove from the base. Hold the base instead of any other parts when lifting the feeder.
Connecting Power
- Insert the 5V power adapter into a wall socket. Plug in the power socket of the feeder.
- Open the battery compartment at the bottom of the unit, and install 3 alkaline D batteries (not included) in case of outage.
- The LCD display will light up automatically indicating the feeder is on now.
  Note:
1. Battery NOT included.
2. Before connecting to power, make sure all parts X3 are clean and completely dry.
3. The battery should power with an output of 4-5V; the battery level icon on the display blinks on a low battery level (<4V).
**Placing Desiccant bag

The PETLIBRO desiccant bag can remove the moisture and odor inside the tank, protect the pet food from oxidation damage, and always be fresh.
Note:**

1. Its recommended to use a desiccant bag and change them every 15 days in case of mold.
2. Please remove the desiccant bag before cleaning the lid.
3. For a better antioxidant effect, tear off the sealing film outside the small package only when you use it.

**Filling Food Tank

**

1. FiR food tank with dry pet food. Close the lid and it will snap into place due to gravity.

Note:

  1. Do NOT use canned, wet or moist pet food.
  2. Recommend kibble size ranging from 2-10mm / 0.07-0.4in in diameter.

Recording a Meal Call
- Press and hold the Record button, start recording after a beep is heard.
- Record your voice for less than 10s. Release the button, 2 beeps will be heard indicating it’s saved.
  Note: When feeding time is up, the recording will be played when food is dispensing.
Manually Feeding Your Pet
Press the Feed button and one portion (2 1/2 tsp / 12.5m0 will be fed each time.

CLEANING & CARE

Its recommended to clean the feeder regularly for the health of your pet.

The washable parts of the Petlibro auto feeder are as follows: food tank, food tray, and lid (without desiccant bag); they can be submerged in water. Clean by hand-washing using cool or warm soapy water.

Dissembling the food tank
If you have food inside the tank or chute, press the Unlocked button and Feed button for a few times to empty first.
Press the food tank buckles with your thumbs, push the tank upward to disassemble.
Dissembling the food tray
Empty the tray, press it down to remove from the base.
Rinse and let all parts air dry completely before assembling.
Note: Be careful not to hurt your fingers when disassembling the food tank by great strength.

WARRANTY

We provide a 1-year warranty for this appliance. Please email our support team at support@petlibro.com if you have any questions, and attach your order ID in your email. We’ll get back to you as quick as possible.

WHAT’S IN THE BOX

1 x WIFI Automatic Pet Feeder
1 x 5V Power Adapter
1 x Desiccant Bag
1 x User Guide Kit

SPECIFICATIONS

Food Tank Capacity	4 liters
Power	DC 5V power adapter;

TROUBLESHOOTING

Problem

| Solution
---|---
The Food won’t come out|

Please be sure to fill in with dry food; kibble size should range from 2-10mm / 0.07-0.min in
Check whether any foreign objects are placed
- disassemble the food tank and check the chute. Also
check the food outlet. the power adapter is connected or there is any outage when no battery is installed.

I can’t disassemble the food tank| Please follow steps in Clean & Care
I can’t hear any voice feeding| Make sure you’ve recorded successfully – unlock the control panel, press the Feed button to check. If no sound is heard, you may need to record again and be sure to save following instructions in the Recording a Neal Call section.
Food volume for each portion is not the same| The first few portions may vary, and it doesn’t mean a faulty equipment. After about ó feedings it should be almost even.
I can’t configure the feeder on my mobile.| Incorrect account and password format — Use only number and letter for username and password, 12 digits at most.
5G not supported – Please use 2.4G wireless network.
Application problem – Some program conflicts may happen. Please restart your mobile
Feeder appears disconnected from WIFI.| Weak disconnection Please check that the distance between your feeder and router is no more than 10m /33ft. and no concrete walls or too many obstacles between them. Otherwise the WiFi network can be weak and cause unstable connection.

Customer Support

PETLIBRO WIFI Automatic Pet Feeder Model: PLAF101 ©Libro Corp. All Rights Reserved. Manufacturer: Shenzhen Libro Technology Co., Ltd.
Address: Building 3, Cloud Park, Shenzhen, China, 518129
Made in China

Icon
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Scan for more detail www.petlibro.com