PETLIBRO PLCT001 Infinity DIY Cat Tree User Manual

ETLIBRO PLCT001 Infinity DIY Cat Tree

COMPONENTS

Prior to assembly, be sure to identify and sort all components shown below.

PlATFORM AND BASE

CUSHIONS

SUPPORT PARTS

OTHERS

ACCESSORIES

ATTENTION

• Side A faces up while assembling
• Place the side A at the base face down then install the anti-slip pad”‘ shown in the picture.

AWARNINGS & CAUTIONS
Please read and follow all warnings and instructions to avoid pet injury or property damages.

• Keep all tools and instructions in a safe place for future reference.
• This cat tree is intended for cat use only, please keep children away.
• Keep all small parts away from children and pets to avoid choking hazards.
• Never climb, rock, shake, step or hang on the cat tree.
•  Place your cat tree indoors, away from direct sunlight or damp areas.
•  Cat trees should be placed on a flat, level surface for stability.
• Check your cat tree often for loose screws or parts that might need re-tightening.
• Do not place heavy items on the product.
•  Do not sit or stand on the product.
•  Inspect product for damage and discard if any part gets worn or damaged.
• Wrong assembly may cause the product to fall over and cause injury.
• For safety, please wear gloves when handling tools and during installation.
• Single-layer weight capacity : 10kg/22lbs.
• Total weight capacity: 50kg/110lbs.

BASIC METHODS

Assemble Two Scratching Posts/Wooden Poles

1. Twist a third of the bolt into the lower scratching post/wooden pole.
2. Twist the upper scratching post/wooden pole into the bolt until it can’t move.

Assemble the Platform and Scratching Posts/Wooden Poles

• Side A faces up.

  1.  Twist a third of the bolt into the lower scratching post/wooden Pole.
  2. Pass the bolt through the hole.
  3. Twist another scratching post/wooden pole into the bolt until it can’t move.

Assemble the Base and Scratching Posts/Wooden Poles

• Side A faces down.
  Hold the scratching post/wooden pole and tighten the 50mm long screw from the bottom with the hex wrench.

Assemble the Top Perch and Scratching Posts/Wooden Poles

• Side A faces up.
  Hold the scratching post/wooden pole and tighten the 50mm long screw from above with the hex wrench.

Assemble the Cushion and Platform

1. . Remove the sticker paper under the cushion.
2. Put the cushion on the platform and press firmly to stick tightly. As the picture shows.

Assemble the Cushion and Top Perch

1. . Remove the sticker paper under the cushion.
2. Put the cushion on the top perch and press firmly to stick tightly. As the picture shows.

Assemble the Tunnel and Platform

• Side A faces up.

  1.  Pass the 30mm long screw through the board and tunnel.
  2. Use a 13mm open ended spanner to tighten the nut inside the tunnel.
  3. Hold the nut, and tighten the screw with the hex wrench.
     Note: To prevent cats hitting their heads while playing, please use the 30mm long screw.

Hang the Toy Ball
Pass the rope of fluff ball through the hole at the end of the top perch cushion and tie a knot as shown in the picture.

How to Use the 16mm Wooden Block

1. Align the 16mm wooden block with the wooden pole first, then align its hole with the hole on the platform.
2. Hold the wooden pole, and tighten the 50mm long screw from above with the hex wrench.

How to Use the PVC Sticker
After assembly, use the PVC sticker to cover the screw hole.

WRONG ASSEMBLY

WARNING
Wrong assembly may cause the product to fall over and cause injury.

CLEANING INSTRUCTIONS

Clean the Felt Bag
*Caution: To avoid damage to the fabric

• Do not machine wash the felt bag.
• Do not use brush to wash the felt bag.
• Never place it in a dryer.
• Never expose it to direct sunlight.
• Never use any other direct heat source (such as a hairdryer) to dry it.
• Do not use bleach.

1. Unzip and remove the felt bag.
2. Submerge the felt bag in cold water, add some mild detergent sate to use on felt.
3. Soak the felt bag in water for a few minutes. Gently hand-wash the felt bag.
4. Rinse and repeat until water is clean.
5. Absorb the remaining water with a dry cloth.
6. Let it air dry

Clean the Boards, Scratching Posts, and Wooden Poles
*Caution: Do not wash in water
To remove hair and dust, use a vacuum cleaner.

1. Moisten a soft cloth with soapy water.
2. Spot clean the stains and soiled areas with a damp cloth.
3. Air dry the wet area completely.

WARRANTY

• 12-month warranty
• Lite-time support
• Please contact our customer service at support@petlibro.com for warranty extension or any questions about the product.
• For more information, please visit www.petlibro.com.

12 DIY WAYS The 12 Installation Methods Below are for Reference.

WARNING: To prevent pets injury, if you do not install it in the recommended 12 DIY ways, please make sure the way you install will not cause the product to tip over.
ATTENTION: Please Install from the Bottom to Top When Assembling.

ABOUT COMPANY

• @Libro Corp. All Rights Reserved.
• Distributor: Shenzhen Libro Technology Co., Limited
• Address: Building 3, Cloud Park, Shenzhen, China, 518129
• Manufacturer: Ganzhou Aigesen Wooden Based Panel Co., Ltd
• Address: Furniture Industrial Park, Nankang District, Ganzhou, Jiangxi
• Province, China
• EPA EST.NO.17055-CHN-1
• Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>