PETLIBRO PLAF301 One RFID Pet Feeder User Manual
- June 2, 2024
- PETLIBRO
Table of Contents
PETLIBRO PLAF301 One RFID Pet Feeder
In the Box
Product Overview
- Food Tank Lid
- Desiccant Bag Holder
- Food Tank
- Infrared Sensor A (Detects pet)
- Control Panel
- Infrared Sensor B (Detects food levels)
- LED Display
- Feeder Base
- Food Bowl Lid Pivot Lock
- Food Outlet
- Infrared Sensor C (Detects food blockages)
- Food Bowl Shields
- Food Bowl Lid
- Stainless Steel Food Bowl
- Bowl Tray
- RFID Reader
- RFID Reader Prongs
- Battery Compartment
- Battery Compartment Cover
- Speaker
- Power Port
- Food Tank Lock
Buttons
Indicators Overview
Indicator Status
Getting Started
Installation
Scan the QR code below to watch the video for the product installation, or
follow the instructions in the manual to install the feeder.
Install the food bowl lid
- Press the locks on both sides of the food tank lid, remove the lid, and take out the accessories from the food tank.
- Install the food bowl lid in the direction shown in the figure.
- After successfully installing the food bowl lid, move the food bowl lid pivot lock to the left to ensure that it’s in the locked state.
Notes:
If the food bowl lid is unlocked, the product will not work properly.
Install the body
-
Place the RFID reader on a flat surface, keeping it close to the power port and away from metal objects.
Notes: The RFID reader is not waterproof. -
Place the stainless steel food bowl and bowl tray in the designated groove of the reader.
-
Open the battery compartment at the bottom of the feeder. Install three alkaline D batteries (not included) in case of a power outage.
Notes- Batteries are not included.
- To avoid sudden power outages and the feeding of your pet affected, do not use the batteries as the only source to power the feeder; the batteries can only be used as an emergency plan.
- To avoid battery leakage, remove the batteries if the device won’t be in use for some time.
- When powered in battery mode, only the RFID recognition function, Wi-Fi function, and feeding function are enabled; all other functions are disabled.
-
Plug the USB cable into the power port at the bottom of the feeder.
-
Place the body in the designated position on the reader.
Note
When installing the body on the RFID reader, if you hear a ‘click’ sound,
indicates that the body is properly installed.
Install the food bowl shields
Insert both shields into the body.
Install the food tank
Press the food tank lock to lock it in place.
Add dry pet food to the food tank
Notes
- To prevent uneven food dispensing, please add enough pet food to prevent a low surplus food alarm triggered.
- Recommended kibble size: 2-15mm (0.07-0.6in) in diameter.
- Do not use canned, wet, or moist food.
Put the food tank lid on
Remove the desiccant bag from the packaging, Place the desiccant bag in the
holder under the food tank lid.
Notes
- It is recommended to change the desiccant bag every 15 days to prevent mould growth.
- Remove the desiccant bag before cleaning the lid.
- Press the locks on both sides of the food tank lid to install the lid in place.
Connect Power
- Plug the 5V power adapter into a power outlet.
- The indicators will light up automatically to indicate the feeder is on.
Multiple Device Installation Guidance
The distance between multiple RFID feeders should be more than 10 inches/25cm
to prevent any potential interference.
App Control
-
Download and install the PETLIBRO app.
Note: There are two similar apps available on your phone’s app store: PETLIBRO and PETLIBRO LITE. Please make sure you download the PETLIBRO instead of LITE. -
Follow the instructions to configure the network.
Pair The Collar Tag
Note: There are two methods to pair the collar tag: sensor-based pairing
and QR code-based pairing. If one method fails, you can switch to the other.
- After successfully adding the device, tap the “ADD COLLAR” button.
- Place the collar tag in the RFID recognition area, as close to the RFID reader as possible.
- After a successful addition, tap “CONFIRM” to pair the collar tag.
- Follow the app instructions to add relevant pet information.
Care And Maintenance
Note
Scan the QR code above to watch the video for the product installation and
cleaning.
- Power off the device before cleaning.
- Do not clean the feeder in a dishwasher. Only the stainless steel bowl is dishwasher safe.
- Use a soft damp cloth to clean the feeder base. Do not wash any part with electronic components.
- Replace the desiccant bag every 15 days to keep food fresh.
Power off
Unplug the cable from the outlet and remove the batteries.
Specifications
Safety Instructions
- Use the feeder in a dry place.
- Use the feeder on a level surface.
- Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation. Keep them away from children and pets.
- Do not use the feeder with pets that are not able to reach the food bowl or with any physical disability.
- Do not immerse the base part in water at any time as it may damage electronic components.
- Do not use the feeder outdoors. Check its operation frequently to be sure it is operating properly.
- Do not disassemble the feeder other than as instructed in this user manual.
- Only use accessories recommended or sold by the manufacturer. The use of accessories not recommended or sold by the manufacturer may cause an unsafe condition.
- Do not modify the feeder.
- Examine the feeder after installation. Do not plug in if there is water on the power cable or plug.
- To avoid tripping, always position the power cable out of the way of foot traffic.
- Do not install or store the feeder where it will be exposed to weather or temperatures below 0°C (32°F).
- Do not use the feeder without adding pet food first.
- Power off the feeder when it’s not in use.
Warranty
- 12-month warranty
- For guidance on product use, please contact our customer service team via email: support@petlibro.com.
FCC statement
This device complies with Part 15 of the FCC Rules. Opera-tion is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including- ing
interference that may cause undesired operation. Changes or modifications to
this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class
B digital device, under Part 15 of the FCC Rules. These limits are designed to
provide reason- able protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used by the instructions, may cause harmful
reference to radio communications. However, there is no guarantee- antee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following- measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
ONE
RFID Pet Feeder
Libro Corp. All Rights Reserved.
Model: PLAF301
Manufacturer: Shenzhen Libro Technology Co., Ltd.
Address: 12/F, Tower B, GALAXY WORLD, Yabao Road, Longgang District, Shenzhen,
China
Made in China
PLAF301_V1.0
FCC ID:2A3DE-PLAF301 IC:28987-PLAF301 CAN ICES-3(B)/NMB-3(B)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.