PETLIBRO PLWF003 Stainless Steel Water Fountain User Manual

PETLIBRO PLWF003 Stainless Steel Water Fountain

Safety Precautions

WARNING

• Dispose of all packaging materials properly. Keep polybags away from children and pets as these bags could cause suffocation.
• Do NOT allow children to play with, in or around the pet water fountain.
• To avoid injury, please keep close supervision when the appliance is used near children.
• Do NOT use the water fountain with pets not able to reach the water tray or with any physical disability.
• Do NOT place any foreign object in the water tank.
• Do NOT disassemble the pet fountain other than components as instructed in this User Manual.
• Do NOT use the pet fountain for anything other than its intended use.
• Only use attachments recommended or sold by the manufacturer. The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition. Do NOT modify the pet fountain.
• Do NOT operate any appliance if the unit is malfunctioning or has been damaged. Do not attempt repairs on the device yourself. Contact our customer service immediately for further instructions.
• Be sure to disconnect the power supply for safety when the appliance is not in use.
• Please disconnect the power supply before maintaining and cleaning the machine.
• Always unplug the appliance when not in use; or before putting on or taking off parts and before cleaning.
• The power adapter and wire plug must not be flooded during cleaning.
•  This product is for indoor use only.
• This product is not allowed to run without water.
• Never pull the electrical power cord to remove the plug from the wall outlet.
• If the plug of this device gets wet, turn off the electricity of that wall outlet. Do NOT attempt to unplug.
• Check the device after installation. Do NOT plug in if there is water on the contact points or plug.
• To avoid tripping, always position the power cord out of the way of foot traffic.
• Do not use the appliance in the bathroom.
• Change the filter every 2-4 weeks or when the flow rate has noticeably reduced. For two or more cats, you may need to replace the filters more regularly if it becomes blocked.

CAUTION

• Do NOT allow pets to chew on or swallow any parts. If you are concerned about the power cord, purchase a cord conduit (a hard-plastic protector) at any hardware store to protect the power cord.
• If an extension cord is necessary, one unit with a proper rating should be used.
• Do NOT install or store the pet water fountain where it will be exposed to weather or temperatures below 0°C / 40°F.
•  Read and observe all important notices listed on the pet water fountain and in the packaging.

Product Overview

1. Water Flow Controller
2. Water Outlet
3. Drinking Basin
4. Filter Cartridge
5. Power Adapter
6. Power Cable
7.  Pump Holder
8. Sponge
9. Water Pump
10. Water Tank

How to Use

• Step 1
  Soak the filter in a clean bowl for 5 minutes .
  Notes:

1. The filter must be fully soaked before the fountain is turned on; otherwise, water may not smoothly disperse through the filter and cause spillage.
2. Do not soak the filter in the water tank of the fountain in case of any surface dust.

• Step 2
  Open the cover by lifting the handle.

• Step 3
  Install the pump holder first, then put the pump into the sponge. Press the pump to make the suction cup under the pump sticks tightly.
  Note: Make sure the pump is fixed in place in the tank.

• Step 4
  Put the activated carbon filter in the filter housing and close

• Step 5
  Fill the tank with water between “min” and “max”.
  Note: To prevent spillage, do not add water above MAX level.

• Step 6
  Put back the cover to form a seal.

• Step 7
  Connect the power adaptor.

Care Instructions

1. Replace the carbon filter and sponge every 2-4 weeks.

2. Clean the pump and fountain every two weeks.
   Take off the pump cover and rotor. Use the brush to clean the parts with water.

3. Keep the water level above the pump, as the pump will fail if it runs without water.

Troubleshooting

soaked. Please soak the filter in a clean bowl (not in the water tank) for 5 minutes before the first use.
The pump stops working.| 1. Fill in water between MIN and MAX. The pump will fail if it runs dry.

2. Clean the pump, water tank, and drinking basin.

3. If the above solutions don’t work, please contact us at support@petlibro.com.

How often should I change the filters? Where to get them?| It’s recommended to replace the filter and sponge every 2-4 weeks. Please contact us at support@petlibro.com to purchase new filters.
Why do I need to soak the filter before first use?| The filters absorb more water (and therefore clean more water) when they’re wet and expanded. Soaking the filter removes particulate matter that may have settled on the filter.

Specification

Output, 5V/1A

Material| SUS 304 stainless steel
Water Tank Capacity| 2L
Operating Temperature| O°C-60°C / 32°F-140°F
Dimensions| 27.Sx 20.5 x 8.2 cm / 10.8 x 8.1 x 3.2 in
Net Weight| 603g / 1.33lbs

Warranty

• 12-month warranty
• Life-time support
• Please contact our customer service at support@petlibro.com for warranty extension or any questions about the product.
• For more information, please visit www.petlibro.com.

ABOUT COMPANY

PETLIBRO Stainless Steel Pet Fountain

• Model,PLWF003
• ©Libra Corp. All Rights Reserved.
• Manufacturer: Shenzhen Libro Technology Co., Limited Address, Building 3, Cloud Park, Shenzhen, China, 518129
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (11 this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>