TSI CH-05AL Cheetah Bead Seater User Manual
- June 5, 2024
- tsi
Table of Contents
TSI CH-05AL Cheetah Bead Seater
- WARNING – Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
- WARNING – Personal Protective Equipment: Safety goggles, gloves, non-skid shoes and hearing protection .
- WARNING – Keep bystanders and children out of the work area while operating this tool.
- WARNING -Always keep work clean, uncluttered, and well lit. Do Not work on floor surfaces that are slippery.
- WARNING – Do not operate this tool if you are tired or under the influence of alcohol, drugs, or medications that could affect your ability to use the tool properly.
- WARNING – Air under pressure can cause severe injury. Never point an air tool at people or animals .
- WARNING – Detach from air supply and release all air pressure before installing, removing or adjusting any accessory on this tool or performing maintenance. Failure to do so could result in injury.
- WARNING – Do not open the Cheetah® Bead Seater air release valve when connecting the air supply hose. When the Cheetah® Bead Seater is not in use, discharge air from tank. Store with valve open in a clean, dry location. Never transport the Cheetah® Bead Seater with air in the tank.
- WARNING – Do not tamper with the safety valve. Do not modify or alter the bead seater in any way .
- WARNING – Inspect before each use. Do not use if broken, bent, cracked or damaged parts are noted (Including warning label). If the unit appears damaged in any way, is missing parts, or operates abnormally, it shall be removed from service immediately. All units that have been dropped, impacted suddenly, or dented should be removed from service.
- WARNING – Only Cheetah® Bead Seating replacement parts should be used on the unit. Decals and parts are available through your Distributor or the manufacturer .
- WARNING – The warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator .
- WARNING – Operator should be familiar with all OSHA regulations (including 29 CFR 1910.177) pertaining to mounting, demounting and inflating all tires
Label Description
GENERAL INFORMATION
USE NEVER CAUTION! discharge Wear a safety Cheetah® glasses aimed at and a hearing person protection
- General: Remove contents from box and assemble as shown below in Fig. 1. Read and follow instructions for optimum use.
- Overview: The CH-5 & CH-5AL Cheetah® Bead Seater accommodates wheels from 4″ to 24.5″. Which includes passenger and light truck tires and most commercial truck tires.
The CH-10 & CH-1 0AL Cheetah Bead Seater accommodates passenger and light truck tires, commercial truck and some implement tires.
All tanks are ASME certified or CE (Europe)
WARNING! AIR IN TANK CAN REACH HIGH PRESSURE
USE NEVER CAUTION! discharge Wear a safety Cheetah® glasses aimed at and
a hearing person protection
Primary Features
*Accessories are available for the Bead Seaters. The accessories are shown throughout this operator’s manual.
Follow these instructions for proper Bead Seating methods and practices.
Set-Up
Verify receiving all the parts described in this instruction. Assemble as shown in Fig. 3 thru Fig. 8.
To install the discharge valve and threaded barrel use a large pipe wrench or a large socket wrench. Tighten so air doesn’t leak out of the fitting. Use Teflon tape where applicable. Tighten the threaded barrel and discharge valve. Put some air in the tank and use soapy water to check fitting connections for air leaks. Tighten them as necessary.
In Fig. 6 Tighten the lock nut ensuring the channel side of the threaded barrel is facing up, See Fig. 5. If the safety release valve in Fig 7. comes loose tighten it as shown.
If the pressure gauge becomes loose tighten it with a wrench as shown in Fig. 8 and test for air leaks with soapy water.
Changing parts or making modifications to the Cheetah® Bead Seater voids the warranty and TSI will not be held liable
How to use
Important: Prepare each wheel. Clean Rims. Dirty rim flanges and poor tire
beads can create flying debris from the rush of air going into the wheel.
TSI suggests using a quick-disconnect fitting (not included) on the air line
to attach the air line to the valve stem, we sell an optional whip hose part
01.109
Remove valve stem core from wheel. Set aside to replace later after bead is
seated. Lubricate tire
beads and rim flanges with approved tire lubricant.
Before placing wheel on tire stand (Fig. 9) connect whip hose to valve stem.
Fig. 10. You may have to thread the air line or part of the whip hose through
the rim center if the valve stem is facing the ground when on the tire stand.
In most cases, the wide flange of the wheel should be facing up. Fig. 9. See
Fig. 10, connect air line to whip hose.
As shown in Fig. 9 positioning a wheel on the tire stand will elevate both the
tire and rim.
The lower tire bead must be resting on the wheel bead-seat area. This
alignment is very important to ensure the tire will capture the air blast
within the tire cavity.
Now you can attempt to seat the tire bead onto the rim.
Note: It’s not always necessary to fill the tank to maximum pressure. The required pressure will vary depending on the size and type of tire. It is best to begin with lower pressure and work up to optimum pressure for your specific tire. Never exceed 120 PSI (Safety release valve is set to 120 PSI).
Firmly hold Cheetah® tank as shown in Fig. 12. Lean forward slightly to hold it in position. Point the threaded barrel down into the tire as shown in Fig. 13. Usually this is a 45 degree angle, you’ll note it can vary from one tire to another. Open valve on whip hose.
Gather your footing, hold one hand onto the Cheetah® handle and the other on
the discharge valve lever. Fully turn the discharge valve lever releasing all
the air into the tire, lifting the bead. See Fig 11.
Once the bead fully moves into position close the whip hose valve. Remove the
whip hose locking chuck from the valve stem and replace valve stem core. With
experience you will recognize filling the tank to capacity isn’t necessary.
The amount of air to seat the bead depends on the tire, most tires can be
seated between 40 PSI- 100 PSI. Several attempts to seat the bead may be
necessary.
Make sure the valve stem core is firmly tightened in place. You are now ready
to place the tire into a tire cage and proceed to inflate the tire to
manufacturer’s tire pressure requirements. Check for leaks. Address leaks and
if necessary repeat process. If none are present, place valve cap on valve
stem and wipe off excess lubricant.
PERFORMANCE, MAINTENANCE AND SAFETY
5 YEARS IN SERVICE DECAL
To ensure the highest level of performance and operator safety, each Cheetah® tank should regularly be inspected for signs of damage due to wear, accidental impact from drops or other shop wear and tear or storage conditions. Inspection of the tank both external/internal and replacement is the ideal approach to insure optimum user safety. Safety related input from our tank manufacturers suggest replacement after 5 years in service.
The (5) years in service is based upon safety related input from our tanks manufacturer’s. Following the maintenance inspection protocol and good judgment of the user, should be the final determination of the unit’s safety and need for replacement. Under NO circumstances should you use a tank with signs of deterioration, damage or malfunction safety valves or gauges.
MAINTENANCE PROTOCO
Use genuine Cheetah® TSI replacement parts. Use of non-cheetah parts will void
the warranty. Under no circumstances should items be welded or attached to the
tank. Use only stock parts as referenced in parts schematic.
TSI Cheetah® warranty does not cover a dropped tank or damage resulting from
dropping the unit. Any tank that has been dropped or shows sign of damage
should be immediately removed from service.
Daily: Inspect the pressure gauge (Part# 01.106) and Safety Release Valve (Part #05.102). Visually inspect the exterior of the tank for rust or deterioration.
Monthly: Pull the ring of the safety release valve to ensure the valve moves freely and isn’t stuck.
Every six (6) months: Visually inspect the interior of the tank for rust or deterioration by removing the discharge valve and threaded barrel. Shine a light into the tank to improve visibility.
Storage and Drain : The Cheetah® should be stored by hanging by the
handle with the valve open. This allows any moisture to drain from the tank
when the Cheetah® is not in use. It also protects the barrel and other
attachments on the Cheetah® from damage.
Discontinue use of tanks should any of the maintenance items need service.
Contact your Distributor or TSI at
800-223-4540 or
602-437-5020 for replacement parts or
units.
CHEETAH® BEAD SEATER
Repair Parts
No| Description| Part No| No| Description| Part
No
---|---|---|---|---|---
1.| Airtank| N/A| 7| 3/4″ – 1/4″ Bushing| 01.107
2.| Pipe Nipple| 01.104| 8| 90° NPT| 03.104
3:| Discharge Valve (Includes Handle)| 02.102| 9| Safety Release Valve| 05.102
4.| Lock Nut| 02.107| 10| Handle & Nut Only| 01.230
5.| Threaded Barrel| 02.103| 11| Ball Valve| 04.103
6.| 200 PSI Gauge| 01.106| 12| Rubber Feet| 12607
Order parts from your distributor or jobber. When ordering parts always give the following information: Part number, description and serial number of your machine.
Reminder: Always exercise caution when using compressed air.
PCL Connector is NOT INCLUDED must be purchased separately.
ACCESSORIES
Difficult wheels?
The magnum barrels provide optimum air dispersion for larger diameter wheels.
The curved tube has holes in it for direct air flow into the tire
CH-ACC Kit:
Tl-87 Shelf (Wall Mounted)
Keep Cheetah® safely off the work floor area
Faster and easier than standard ball or butterfly discharge valve operation. Attaches easily to existing pipe nipple, replacing manual discharge valve. Discharges tank with the press of a button. Safety cover prevents accidental trigger release. Includes our new improved Jet Barrel for greater air volume delivery.
Warranty Statement & Return Policy
Warranty & Workmanship you can depend on.
With over 25 years of manufacturing experience we maintain the ability to
provide competitive prices while employing and manufacturing the majority of
our products in the USA. Pride in our workmanship and standing behind each and
every product is not just our claim but our uncompromising responsibility. TSI
equipment is warranted to be free from defects in materials and workmanship
for a period of
one year from the date of original purchase to the original owner. Repair
labor is warranted for 90 days from the date of original purchase. Bushings,
blades, bearings and normal wear and tear are not covered under warranty.
Careless handling, negligence, misuse, abuse, mutilation, improper operation,
making unauthorized repairs, additions, and or alterations automatically
cancel this warranty and relieves TSI of any obligation. Cheetah tanks claimed
to be defective while under warranty will be evaluated at our manufacturing
plant and either repaired if possible or exchanged and returned or credit
issued to the customer account at our discretion. Damage resulting from
dropping the tanks will not receive warranty consideration. Warranty parts
need to be returned prepaid to the plant for credit. Any replacement parts
shipped from the plant will be shipped at the customer’s expense. Machines
requiring warranty work must be brought to the manufacturing plant in 201
Chelsea Rd, Monticello, MN or to a repair facility authorized by TSI.
Return Policy :
!!WARNING!! Goods returned without an RGA will be refused. A Returned Goods
Authorization form must be obtained before returning any material or goods.
All non-warranty returns will be subject to a 15% restocking fee plus any
additional charges for reconditioning / repacking.
Documents / Resources
| TSI
CH-05AL Cheetah Bead
Seater
[pdf] User Manual
CH-5, CH-05AL, Cheetah Bead Seater, CH-05AL Cheetah Bead Seater, CH-10, CH-10L
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>