SpeedyBee F7 35A BLS Mini Stack Flight Controller Stack User Manual

F7 35A BLS Mini Stack Flight Controller Stack
User Manual

Part 1 – Overview

Specs Overview

screws/Silicone grommets
Dimension| 32mm(L) x 35mm(W) x 13mm(H)
Weight| 12.7g

Dimensions

Package

• SpeedyBee F7 Mini Flight Controller x 1

• SpeedyBee 35A BLHeli_S Mini 4-in-1 ESC x 1

• Manual & App Download Card x 1

• XT30 Power Cable(Length: 7cm) x 1

• 8pin JST cable(For FC & ESC Connection） x 1

• 35V 470uF Capacitor x 1

• M2 Accessories
  • M2(Diameter) 20mm(Length) Screw x 4
  • M2(Diameter) 25mm(Length) Screw x 4
  • M2(Hole Diameter) * 6.6mm(Height) Anti-vibration Silicone Grommets x 9
  • M2 Silicone O-Ring x 5
  • M2 Nylon Hex Nut x 5

• M3 Accessories
  • M3(Diameter) 20mm(Length) Screw x 4
  • M3(Diameter) 25mm(Length) Screw x 4
  • M3(Hole Diameter) * 6.6mm(Height) Anti-vibration Silicone Grommets x 9
  • M3 Silicone O-Ring x 5
  • M3 Nylon Hex Nut x 5

FC & ESC Connection

Use any end of the 8-pin JST cable to connect the FC to the ESC.

Part 2 – SpeedyBee F7 Mini Flight Controller

Layout

LED Indicator Definition
RED LED – Solid Red after powering up.
GREEN LED – Blinking Green indicates Bluetooth is open and waiting for connection; Solid Green indicates Bluetooth is connected.
BLUE LED – Flight controller status light which is controlled by the flight controller firmware.

BOOT Button
Only if the flight controller gets bricked and can’t power up, please follow these steps to re-flash firmware for it:

1. Insert a USB A to TYPE-C cable to your PC.
2. Press and hold the BOOT button, insert the USB cable into the flight controller, then release the BOOT button.
3. Open Betaflight/Emuflight/INAV configurator on the PC, go to the ‘Firmware Flashing’ page, choose the target ‘SPEEDYBEEF7MINI’ and flash.

FC’s Peripheral Connection

APP

• Get the SpeedyBee App
  Search ‘SpeedyBee’ on Google Play or App Store. Or download the Android .apk file on our website: https://www.speedybee.com/download.

• Connect the App
  

FC Firmware Update

SpeedyBee F7 Mini does not support wireless firmware flashing, so please flash firmware for it on your PC following the steps below:

1. Connect the flight controller to the PC with a USB cable
2. Open Betafight/Emuflight/INAV configurator on your PC. Take the Betaflight configurator as an example, go to the ‘Firmware Flashing’ page, choose the target  ‘SPEEDYBEEF7MINI’, and flash.
   

Parameters

FC on the PC
Download/Analyze Blackbox| Not supported. Please download and analyze Blackbox data on the PC
QII Air Unit Soldering Pads| Supported
Flash(for BlackBox)| 8MB
Current Sensor| Supported, Scale=250 Offset=-500
BetaFlight Camera Control Pad| Yes(CC pad)
Power Input| 3S – 6S Lipo
5V Output| 6 groups of 5V output, five +5V pads, and 1 BZ+ pad( used for Buzzer). The total current load is 2.5A.
9V Output| 2 groups of 9V output, the total current load is 2A.
3.3V Output| Supported. Up to 500mA current load.
ESC Signal Pads| M1 – M4
CART| Full UART * 3(UART1, UART2, UART3)
ESC Telemetry UART| R4(UART4)
12C| Not supported
LED Pad| Used for WS2812 LED
Buzzer| BZ+ and BZ- pad used for 5V Buzzer
BOOT Button| Used to enter DFU mode
RSSI Input| Not supported
SmartPort| Use any TX pad of UART for the SmartPort feature.
Supported Flight Controller Firmware| BetaFlight(Default), EMUFlight, INAV
Firmware Target Name| SPEEDYBEEF7MINI
Mounting| 20 x 20mm, 3.5mm hole diameter
Dimension| 30 x 30 x 7.5mm
Weight| 5.7g

Part 3 – SpeedyBee 35A BLS 4-in-1 ESC

Layout

|
---|---

Connection with Motors & Power Cable

Note: In order to prevent the stack from being burnt out instantaneous voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.

ESC Configuration

ESC Firmware Update

You could flash both BLHeli_S and Blue Jay firmware for this ESC via Bluetooth.Note: ESC Type should be set as ‘J-H-40’.

Parameters

References

• download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>