WESTINGHOUSE SR29ST01C-99 Solar Powered String Light User Manual

June 5, 2024
Westinghouse

SR29ST01C-99 Solar Powered String Light

24-LIGHT 48FT COLOR CHANGING SOLAR LED STRING LIGHT WITH WIRELESS REMOTE CONTROL
ITEM: SR29ST01C-99

INSTRUCTIONS

FOR FIRST TIME USE: SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8-12 HOURS WITH THE SWITCH IN THE “ON” POSITION TO ALLOW THE
RECHARGEABLE BATTERIES TO REACH MAXIMUM CAPACITY.

ASSEMBLY

Slide solar panel connector (Part B) into the slot on the back of solar panel (Part A). Slide the pole (Part C) over solar panel connector (Part B). Remove the ground stake (Part D) from the bottom of the pole (Part C), flip so that the pointed end is facing outward and reinsert it into the bottom of the pole (Part C). Carefully insert the complete assembly into the ground where desired. Apply pressure to the pole NOT THE SOLAR PANEL when inserting into the ground.

NOTE: If the ground is hard and packed, moisten the ground with water before inserting the stake to avoid breakage.

INSTALLATION

Multiple mounting options for solar panel:

  1. Ground Installation
  2. Clip mount installation
  3. Wall mount installation

REMOTE CONTROL

remote button

REMOTE IS INTENDED FOR DRY LOCATIONS

Remote Control Operation
– The remote control unit will operation lights within 49ft (15m) range.
– Install batteries and point remote towards string light to activate and use the DIMMER, RGBW SELECTOR, COLOR SELECTOR, and LIGHT EFFECTS buttons to select desired features.

BATTERY
Requires 2 AAA Battery (included)

TROUBLESHOOTING

If the light does not turn on, remove the battery, wipe both ends with a clean, dry cloth and reinstall the battery. Check the battery to ensure that it is making secure contact with the terminals.
If this does not work, replace with a new battery.

REPLACING THE BATTERY

Slide the power switch to the “OFF” position. Remove the four screws from the top section using a Phillips head screwdriver. Remove the old battery and replace it with a new 3.7V, 2400 mAh lithium (18650) rechargeable battery. Replace the top section with the four screws. Slide the power switch to the “ON” position.
For optimal performance, allow solar light to charge in direct sunlight for 8-12 hours with power switch in the “ON” position.

1. Ground Installation

SOME PARTS MAY COME PRE-ASSEMBLED

2. Clip Mount Installation

3. Wall Mount Installation

WARNING: Do not dispose of lithium batteries in municipal waste stream or by fire as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride) batteries.

For additional help and information regarding installation, contact Customer Service at 1-844-551-0680, 8am-5pm,CST Monday – Friday
customerservice@qx-usa.com
, WESTINGHOUSE, are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved.

INSTRUCTIONS

FCC WARNING:

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF Exposure: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Portable device statements
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Westinghouse User Manuals

Related Manuals