Dgl Group NOR-EW-RCAP Rugged 3-In-1 LED Power Wireless Light Bank Speaker User Manual
- June 5, 2024
- DGL GROUP
Table of Contents
Dgl Group NOR-EW-RCAP Rugged 3-In-1 LED Power Wireless Light Bank Speaker
OUTDOOR LIGHT
WELCOME
Thank you for yovr purchase of this EDGEWOOD™ Rugged 3-in-1 comping light.
Light up any rood, Wslen to music, and keep all of your devices charged. Good
for use indoors or outdoors.When the products power is running low, simply
leave in direct sunlight to charge with its built-in solar panels. No need to
plug ln to charge!
Please read this entire manual and retain for later reference as needed.
FEATURES
- Bluetooth compatible for phones calls and music
- SD Card reader for MP3s
- 2200 mAh battery bank
- 2 Light styles (Flashlight & Lantern)
- Solar panels for charging
- FM Radio
SPECIFICATIONS
- Capacity: 2200 mAh
- Materials: ABS
- Frequency: 20-20kHz
- Charging time: 8-10 hrs
- BT Range: 32FT (10m)
- Speaker Power: 4O./3W
- Frequency Range: 20–20kHz
- Size: 6.9″ X3.7″ X 3.7″ [175mm X 94mm X 94mm)
- FCC ID: 2MNZRCAP
- BT ID:D051448
DGL Group guarantees the q.;ality of tlis product. For quei!ions or comment:;,
please feel free to contact us vio emai at
[email protected]
Distributed by DGL Group, LTD.
195 Raritan Center Parkway, Edison, NJ, 08837, USA.
Product Daigram
SPEAKER INSTRUCTIONS
CONNECTING BLUETOOTH MODE
- Turn speaker on using ON/OFF switch localed on the front of the product
- Wait for LED indicator to flash blue
- Locate the speaker on your device, name: EW-RCAP
- Connect on your device, LED indicator will stop flashing once connected
- To skip o song press the “+” button, to increase volume press and hold
- To ploy a previous song press the”-” button, to decrease volume press and hold
- To Play/Pause use the ” ►” button
RADIO MODE
- Turn speaker on using ON/OFF switch located on the front of the product
- Press the “M” button to change from Bluetooth to FM mode
- Press the”►” button to begin searching for Rodia pogroms
- To go ta the next station press the”+” button. to increase volume press and hold
- To go bacl:::to a previous station press the”-” button to decrease volume press and hold
- Use the”►” button to scan for available stations
SD CARD MODE
- Insert SD card into slot on the top of the product
- Turn speaker on using ON/OFF switch localed on the front of the product
- Press the “M” button to change to Music Mode
- Music will play in the order it appear5 on the SD card
- To skip a song press the”+” button, to increase volume press and hold
- To play a previous song press the”-” button, to decrease volume press and hold
- To Play/Pause use the”►” button
CHARGING INSTRUCTIONS
- TO CHARGE VIA SOLAR PANELS: Open the top lid to expose panels, leave in direct sunlight until Indicator light is solid red. Close Lid immediately to ovoid over charge
- TO CHARGE VIA AC INPUT: Plus product in via Micro USB input. LED indicator will flash red until product is ful charged. Unplug from AC immediately to avoid over charge
- TO CHARGE USING BUILT-IN POWER BANK: Connect device to product using USB port on front of product. LED indicator will turn solid Blue when device is full charged
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the followillQ two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received.
including interference that may cause undesired operation.
Please note that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC INSTRUCTIONS FOR A CLASS B DIGITAL DEVICE OR PERIPHERAL
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful inlet1erence to radio communications. However,
there is no guarantee that intet1erence will not occlK in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
an, the user is encouraged to try to correct the inlet1erence by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.