BORMANN PRO BBP4600 Brushless Brush Cutter Double Battery User Manual

BBP4600
036807

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described/illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• Please note that our equipment has not been designed for use in commercial, trade, or industrial applications. Our warranty will be voided if the machine is used in commercial, trade, or industrial businesses or for equivalent purposes.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair, or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.

Technical Data

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described/illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• Please note that our equipment has not been designed for use in commercial, trade, or industrial applications. Our warranty will be voided if the machine is used in commercial, trade, or industrial businesses or for equivalent purposes.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair, or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.

Safety Instructions

WARNING ! READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result in electric shock, fire, and /or serious personal injury.

Work area

1. Keep the work area clean and well-lit. Cluttered and dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety
(The following applies only to tools with a separate battery pack)
A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.

Personal Safety

1. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
3. Avoid accidental starting. Be sure the switch is in the locked or off position before inserting the battery pack. Carrying tools with your finger on the switch invites accidents.
4. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations
5. Use safety equipment. Always wear hearing and eye protection, Dust mask, non-skid safety shoes, hard hat must be used for appropriate conditions.

Power tool use and care

1. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate at which it is designed.
2. Do not use the tool if switch does not turn on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired.
3. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users
4. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control.
5. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using . Many accidents are caused by poorly maintained tools.
6. Use only accessories that are supplied with your model. Other accessories may not be suitable for this tool and may create a risk of injury when used.

Intended Use
The tool is intended for domestic use, for trimming grass, weeds, and nettles, and cutting brushes.
It is designed for trimming grass and brushes growing on slopes, under obstacles and lawn edges that cannot be reached by the lawn mower. The garden tool is not intended for commercial or industrial use.

Device-specific safety instructions

• The operator must use the product in accordance with the regulations. The local conditions must be taken into account. When working, pay attention to other people, especially children.
• Never allow children, persons with physical, sensory, or mental limitations or a lack of experience and/or knowledge, and/or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator.
• Children should be supervised to ensure that they do not play with the product. When working with the machine, always hold it firmly with both hands and provide for a secure stance. The garden tool is guided more secure with both hands.
• Always wait until the machine has come to a complete stop before placing it down.
• Never operate the machine with a defective protection guard/cover or without a safety device. Ensure that these are properly mounted. Never use the garden tool when incomplete or after unauthorized changes.
• Never operate the machine if the cord is damaged or worn.
• Never replace non-metallic cutting elements with metal cutting elements.
• Never repair the garden tool yourself unless you are qualified to do so.
• Other persons and animals should remain or be kept a suitable distance away when using the garden tool. The operator is responsible for third parties in the work area.
• Wait until the cutting head has completely stopped before touching it. The cutting head continues to rotate after the trimmer is switched off; a rotating cutting the head can cause injury.
• Work only in daylight or in good artificial light.
• Avoid operating the trimmer in bad weather conditions especially when there is a risk of lightning.
• Operating the trimmer in wet grass decreases the efficiency of performance.
• When transporting, switch the machine off and remove the battery.
• Always ensure a safe working position when working with the trimmer. Always keep your hands and feet at a safe distance from rotating parts.
• Keep the balance all the time while trimming to prevent falling over.
• Take care when placing a product on floor, as it may become a trip hazard.
• Remove the battery before replacing the spool.
• Inspect and maintain the trimmer regularly.
• Always wear gloves when cleaning products or replacing cutting means.
• Be careful of injuries from the blade used for cutting the cutting line. After feeding the cutting line, always re-turn the trimmer to a horizontal working position before switching it on.

Switch the machine off and remove the battery:

• Whenever you leave the machine unattended for any period of time
• Before replacing the cutting line
• Before cleaning or working on the trimmer
• Before storing the trimmer Store the product in a secure, dry place out of the reach of children. Do not place other objects on top of the product. Do not use the garden tool as a walking stick.

Recommendations for Optimal Handling of the Battery
Battery
Vapours may leak out In case of unauthorised use or when using a damaged battery. Bring fresh air and seek medical advice if experiencing difficulties. Vapours may irritate the respiratory system.

Risk of fire! Risk of explosion!
Never use damaged, defective or deformed batteries.
Never open or damage the battery or let It fall on the ground.
Never charge the battery in an environment with acids and easily flammable materials.
Protect the battery against heat and fire.
Never put the battery on heaters and do not expose It to strong sunlight for a long time.
After being subject to heavy load, let the battery cool down first.
Short circuit- do not bridge the battery contacts with metal parts.
The battery must be packaged (plastic bag box) or battery contacts must be sealed up for battery disposal, transport or storage.

Charging batteries
Warning: Use only the original charger to charge the batteries supplied by the manufacturer. Only batteries and chargers designed by Bormann can be used in conjunction with this product.
The use of any other types of batteries/chargers in combination with this product is considered abuse and will void the warranty.
Once connected to the power supply, the battery can be recharged without the need for monitoring. The complex construction of the circuit monitors the condition of the battery by adjusting the recharge current to match the requirements. When the recharge cycle is complete and to maintain full capacity, a low-voltage output current will continue to be powered as needed.

Warning!

• Check the status of the charger and battery before each charge. If there is any indication of a fault then do not continue, seek advice from an authorized vendor.

Battery pack efficiency and charging advice
Recharge the battery packs before they become completely exhausted
When you feel that the power of the tool becomes weaker, stop using the tool and recharge the battery packs. If you continue to use the tool and exhaust the electric current, the battery pack may become damaged.
Avoid recharging at high temperatures. A rechargeable battery pack will be hot immediately after use. If such a battery pack is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery pack and recharge it after it has cooled for a while.
The battery pack should only be used and/or charged when the battery pack temperature is between 50C and 300C.
The battery pack needs to be warmed-up or cooled down in order to prevent damage to the batteries internal components.
Note: Failure to warm up or cool down a battery pack could result in serious damage to tie battery, charger and user.

Description of main parts (Picture A)

Assembly instructions/main adjustments/operating instructions

Attaching the U-shape handle
Unscrew the handle adjusting knob (Fig 1), take out the components (Fig 2), but the handle seat under the handle (Fig 3), cover the handle seat and make sure the two parts of the handle seat are well jointed (Fig 4), but the spring in the boss and screw the knob until the handle is fixed tightly on the pole of the machine (Fig 5) .
Adjusting Work Height
Adjust the handle according to your comfortable position, keep space to prevent the cutting tool from cutting the ground.
Use the supplied tool to tighten or loose the screw with the clamping rings to adjust the fixing position of the wire according to different needs (Fig 6).
Assembling the brush cutter
Mount the shield at the correct position, and fix it with the screws provided (b1). fix the stop collar to the shaft (b2), add the dust cover (b3-b4), assemble the blade, and press the plate (b5-b6). use the provided pin to lock the spindle, fix the press plate with a flange screw, and tighten it with provided socket (b7-b9).
Assembling the string trimmer
Mount the shield at the correct position, and fix it with the screws provided (c1). fix the stop collar to the shaft (c2), fixing the hemline to the shield, and fix the screws tightly
with the provided tool (c3), add the dust-proof shield (c4), use the provided pin to lock the spindle, fix the spool to the machine, and tight it.
The trimmer is equipped with an auto-feed system, which automatically rolls off the line to retain the cutting diameter.
To use line cutting, the shield hemline must be attached to the shield.
Recommended position for cutting

How to Joint poles
The pole of a machine is divided into two parts, joint the two parts in correct position( step e1-e2), and tighten the knob (e3).
Shoulder belt fixing and releasing
Fix the clap ring on the pole of a machine according to your need, hook the belt on the clap. To release the belt, press the buckle with pressure.

Winding line on spool

How to switch on/stop

1. Press the lock-off button (4), squeeze the trigger (3) to start the machine.
2. Release the trigger (3) to stop the machine.
3. The machine is equipped with a reverse rotation switch for getting rid of the grass winding on the shaft, then press it, the user will hear a sound alarm, press the button, and trig- ger like Step 1 to start reverse rotation. After two seconds, the reversing rotation stopped automatically.
4. Restart the machine as described in step 1 for trimming.

Inserting the full charged battery packs
Note: Using unsuitable batteries can lead to malfunctions or damage to the machine. To start the machine, 2 battery packs must be inserted. To keep the battery packs working for a longer time, ensure full-charged battery packs are used.
Insert the charged battery. Ensure the battery is inserted correctly.
To remove the battery from the machine, press the battery unlocking button (2) and pull the battery out.

Warning: For more information regarding the charging process and safety instructions please refer to the charger’s instructions.

Maintenance and Troubleshooting

Maintenance

Regular inspection and cleaning reduce the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. Avoid blocking the air inlets and vacuum the ventilation slots regularly.
WA RNING: Always remove the rechargeable battery from the device before all work.

• Replace all damaged or worn parts to ensure the power tool is always ready for safe operation.
• Clean ventilation slots and openings with a brush.
• DO NOT use any solvents or cleaning agents containing chemicals that could damage the plastic parts. Wipe the housing clean with a cloth.
• Always store the leaf blower in a dry, frost-free location beyond the reach of children.
• Store and charge your rechargeable batteries at a cool location. Temperatures above or below normal room temperature shorten the lifespan of the rechargeable batteries.
• Do not store rechargeable batteries when discharged. Wait until the rechargeable battery has cooled down and charged it completely.
• Rechargeable batteries gradually lose their charge. The higher the temperature, the quicker they lose their charge. For longer storage periods, recharge the rechargeable battery every one or two months. This will extend the lifespan of the rechargeable battery.

Troubleshooting

Problem| Possible Cause| Remedy
Unit does not start| Battery was not installed properly
The b very is not charged| Check battery installation
Check battery charging requirements
The battery will not charge| T se to the charger| Connect the battery to the charger
The charger is not in the socket| Connect the charger to a working outlet.
Check current at receptacle by plugging in a lamp or other
appliance Check whether receptacle is connected to a light switch which turns the power off when you turn out the lights
The air temperature is too high so low \ 11.| Attempt to charge the battery in a room where the surrounding air temperature is above 4,5 °C or below + 40,5 °C
Important: Please note, that all repairs/services should be carried out by a qualified person.

Handling and Storage
Care must be taken when handling this product.
Dropping this power tool could have an effect on its accuracy and could also result in personal injury. This product is not a toy and must be respected.
Environmental conditions can have a detrimental effect on this product if neglected.
Exposure to damp air can gradually corrode components.
If the product is unprotected from dust and debris, components will become clogged.
If not cleaned and maintained correctly or regularly the machine will not perform at its best.

Disposal
At the end of the machine’s working life or when it can no longer be repaired, ensure that it is disposed of according to national regulations.
— Contact your local authority for details of collection schemes in your area.
In all circumstances:

• DO not dispose Of power tools with domestic waste.
• DO not incinerate.
• Do not dispose of as unsorted municipal waste.

Warning!

• Do not put the battery pack on fire or mutilate; cells may burst or release toxic materials.
• Do not short circuit cells, may cause burns.
• The battery pack must be removed from the appliance before it is scrapped.
• The battery pack is to be disposed of safely.
• Do not mutilate batteries; corrosive electrolytes will be released.
• Do not dispose of batteries or cells in a charged condition.

Expired batteries must be recycled/disposed of in accordance with the appropriate regulation or legislation. They should be returned to your local warranty agent/stockist.

WWW.BORMANNTOOLS.COM

Documents / Resources

| BORMANN PRO BBP4600 Brushless Brush Cutter Double Battery [pdf] User Manual
BBP4600, Brushless Brush Cutter Double Battery, Brushless Brush Cutter, Brush Cutter, BBP4600, Cutter
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>