iLuv Bluetooth Alarm Clock Speaker with Wireless charger User Manual

June 5, 2024
iLuv

Bluetooth Alarm Clock
Speaker with Wireless charger and FM Radio

Morning Call 6Q
User Manual (Ver 1.0)

WARNING AND SAFETY INSTRUCTIONS


The lightning flashes with [ arrowhead symbol, [ within an equilateral [ triangle, is intended to [ alert the user to the [ presence of un-insulated [‘dangerous voltage” [ within the product’s [ enclosure that may be [ of sufficient magnitude [ to constitute a risk of electric shock to persons.| CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.| The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

  1. All the safety and operating instructions should be read before the product is operated
  2. The safety and operating instructions should be retained for future reference.
  3. All warnings on the product and in the operating instructions should be adhered to.
  4. All operating and use instructions should be followed.
  5. Use of controls or adjustments or performance other than those specified may result in hazardous radiation exposure.
  6. Do not use this product near water or exposed to rain to prevent fire or shock hazards, i.e. bathtub, washbowl, kitchen sink, laundry tub, wet basement, or swimming pool, etc
  7. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Clean only with a dry cloth.
  8. Unplug Morning Call 6Q during lightning storms or when unused for long periods of time.
  9. When the main plug is connected, Morning Call 60 is operational. In order to disconnect Morning Call 60 completely, the main plug should be disconnected from the main socket outlet.
  10. The battery should not be exposed to excessive heat, such as sunshine or fire.
  11. If the battery is incorrectly replaced, it may cause an explosion. Replace only with the same or equivalent type.

WHAT”S INCLUDED

OVERVIEW OF THE PRODUCT

1. RADIO/BLUETOOTH ON/OFF, STOP ALARM
2.  UP/DOWN (Setup only)
3.  SLEEP
4. BLUETOOTH/PAIR
5. PLAY/PAUSE
6. FM RADIO
7. PRESET
8. SET TIME
9. FREQ/TRACK -/+
10. ALARM 1 SET/ON/OFF
11. SNOOZE/DIMMER
12. (Et ALARM 2 SET/ON/OFF
13. VOLUME -/+
14.  WIRELESS CHARGING PAD| 15. PM INDICATOR I
16. LOW BACKUP BATTERY, INDICATOR I
17. ALARM 1 INDICATOR
18. LEFT SPEAKER I
19. BUZZER INDICATOR
20. FM RADIO INDICATOR
21. RIGHT SPEAKER
22. ALARM 2 INDICATOR
23. PRESET INDICATOR,
24. SLEEP INDICATOR
25. BLUETOOTH INDICATOR
26. WIRELESS CHARGING INDICATOR 1 1
---|---

iLuv Bluetooth Alarm Clock Speaker with Wireless charger -
fig327. FM RADIO ANTENNA
28. DC POWER JACK
29. USB CHARGING PORT
30. BATTERY COMPARTMENT COVER

POWER ON

CONNECTING POWER

Connect the DC plug of the power cord to the 28 DC POWER JACK on the back of the unit and connect the AC plug to a nearby wall outlet.

  • Note: Please install backup batteries (not included) to keep settings including time, alarms, and FM presets when the AC power is disconnected.

SET CLOCK TIME

**** The default time is set to 12:00AM in 12 Hour Time format. (The display flashes 12:00 if the clock time is not set.)

  1. Press & HOLD 8 [Time] for 2 seconds to enter the Time Setup mode. ’12hr’ will be flashed on the screen.
  2. Press (2)(Up/Down] to toggle between 12hr or 24hr formats and press 8 [Time] to confirm the format.
  3. While Hour is blinking, Press 2 [ /Up/Down] to adjust hour (Press & HOLD to fast adjust) and press 8 (Time] to set hour.
  4. While Minute is blinking, press 2 Up/Down] to adjust minute (Press & HOLD to fast adjust) and press 8 [Time] to set minute and complete the time setup.

SET ALARMS

****TO SET AN ALARM:
Alarm Time > Alarm Source > Alarm Sound Volume Default Alarm Time: Alarm 1 – 6:00 AM, Alarm 2 – 7:00 AM

  1. Press & HOLD 10 [Alarm 1] for 2 seconds to enter the ALARM SETUP mode. Once in the alarm setup mode, the display will start blinking.

  2. Set Alarm Time:
    While Hour is blinking, press 2 [Up/Down] to adjust the hour (Press & HOLD to fast adjust) and press 10 [Alarm 1] to set the alarm time hour. While Minute is blinking, press 2 (Up/Down] to adjust minute (Press & HOLD to fast adjust) and press 10 [Alarm 1] to set alarm time minute.
    iLuv Bluetooth Alarm Clock Speaker with Wireless charger -
fig6

  3. Choose Alarm Source:
    Press 2 [/Up/Down] to choose the alarm source between 19 Buzzer or 20 FM Radio. The source you are currently setting will blink. Press 10 [Alarm 1] to confirm the alarm source.

  4. Set Alarm Sound Volume:
    Press 2 [Up/Down] to adjust the alarm sound volume level between V5 to V30 from the initial level of V15. Press 10 [Alarm 1] to confirm the volume level. (Tuned channel on the radio will be used for the radio alarm.)

  5. Once the alarm setup is completed, the corresponding alarm indicator will be displayed.
    Note: Apply the same routine to set Alarm 2 with 0 [Alarm 2] button.

ENABLE/DISABLE ALARM

** Please make sure if any of Alarm 1 or Alarm 2 is disabled by turning each one-off, the specified alarm sound won’t be played at the alarm time. It should be turned on again to be enabled.
Alarms can be Enabled/Disabled by pressing
10 [Alarm 1] or   12 [Alarm 2]. When 17 [1] and/or 22 [2]** is showing, the alarm is set to ON and will activate at the scheduled time. If the indication is not showing, the alarm is set to OFF.

SNOOZE/STOP ALARM

  1. When the alarm is activated, the corresponding 17 Alarm 1 or 22 Alarm 2 indicator will blink on the display.
  2. Press 11 [Snooze] to temporarily silence the alarm. The alarm will snooze and reoccur at an interval of every 9 minutes. The corresponding 17 Alarm 1 or 22 Alarm 2 indicator will blink on the display during the snooze period.
  3. To STOP the alarm completely, press 1 [ ] This will stop the alarm until the next alarm time.

SLEEP TIMER FUNCTION

**** The Sleep Timer Function allows you to set a stop action for the FM Radio or Bluetooth after the specified time has elapsed.

  1. Press 1 [ ] to turn on the audio function.

  2. Press 4 [ ] or 6 [FM] to select the desired audio source from Bluetooth or FM Radio. (Go to page 16 for Bluetooth and page 14 for FM Radio to refer setup instructions of each.)

  3. Press 3 [Sleep] to set the sleep timer while Bluetooth audio or FM Radio is playing. Continue to press 3 [Sleep] until reach to the desired timer from 10 to 90 in 10 minutes interval and wait 5 seconds to keep the selected timer: 90 > 80 > …. > 10 > OFF.

  4. 24 Sleep indicator is displayed once the sleep timer is set.
    iLuv Bluetooth Alarm Clock Speaker with Wireless charger -
fig10

  5. The Bluetooth audio or FM Radio will automatically turn off once the set timer expires.

  6. To check the remaining time until sleep, simply press 3 [Sleep]. The timer will change to the next timer interval if 3 [Sleep] is pressed again while the remaining time is displayed.

  7. To turn off the timer, press 3 [Sleep] repeatedly until the value toggles to OFF and wait 5 seconds. 24 SLEEP Indicator will disappear.

FM RADIO

USING FM RADIO

  1. Unravel and extend the antenna to improve the FM radio signal reception.
  2. Press 1 [ ****] to turn on the audio function.
  3. Press 6 [FM] to select FM Radio.
  4. Press 9 [ ] or [ ] to change the FM radio frequency.
  5. Press & HOLD 9 [ ] or [ ] to automatically scan the available channels.
  6. To turn the FM radio off, press 1 ( ****).

SETTING FM RADIO PRESETS

****Preset option is only available when the Radio is on.

  1. While FM radio is turned on, press 9 [ ] or [ ] to select the desired frequency.
  2. Press & HOLD 7 [Preset] until the preset number is blinking.
  3. Toggle through 9 [ ] or [ ].
  4. Press 7 [Preset] to program the preset with the selected frequency.

USING FM RADIO PRESETS

  1. While FM radio is turned on, Press 7 [Preset] and press 9 [ ] or [ ] to change the preset stations: P01 > P02 > … L > P20

BLUETOOTH

PAIRING WITH OTHER DEVICE
****Effective Bluetooth range: 33ft (10m)

  1. Press 1 [ ****] to turn on the audio function.

  2. Press 4 [ ****] to select Bluetooth.

  3. If the unit is turned on for the first time, it will automatically enter the pairing mode and the 25 Bluetooth indicator will blink.

  4. Go to settings – Bluetooth on your mobile device and turn on Bluetooth. iPhone/iPads will scan for devices automatically while Android devices will require you to press Scan.

  5. Tap “iLuv MORCAL6Q” from the discovered devices list.

  6. Once two devices are connected successfully, a voice prompt “Bluetooth connected” will be heard and the 25 Bluetooth indication stops blinking.
    Note: To enter the paring mode manually, press & HOLD 4 [ ****] for 2 seconds after turning on the audio function.

AUTO RECONNECTING

  1. If the paired mobile device is out of range or disconnects from the Morning Call 6Q, the 25 Bluetooth indicator will start to blink. The connection will automatically be restored once the paired device appears within range.
  2. In case of disconnection or if the connection is not restored automatically, press & HOLD 4 [ ****] for 2 seconds to reconnect or restart pairing.

MUSIC PLAYBACK

  1. Once connected to your device, play music or audio from your preferred app.
  2. Press 5 [ ****] to play your music.
  3. Press 5 [ ****] to pause while music is playing
  4. Press 13 [Volume Up/Volume Down] to increase or decrease volume (00-30).
  5. Press & HOLD 9 [ ] to skip to the previous track.
  6. Press 9 [ ****] to skip to the next track.

DISPLAY DIMMER

  1. Press 11 [Snooze/Dimmer] to adjust the brightness from 10 levels; 100 (maximum brightness) to 00 (mini-mum brightness).
  2. The default brightness level is 100.
    iLuv Bluetooth Alarm Clock Speaker with Wireless charger -
fig18

USING Q! WIRELESS CHARGING

**IT IS SUGGESTED TO CHARGE YOUR PHONE WITH A CABLE INSTEAD OF A WIRELESS CHARGER DURING THE PHONE SOFTWARE UPDATE. OTHERWISE, CHARGE YOUR PHONE FULLY BEFORE THE PHONE SOFTWARE UPDATE.
Place your Qi-enabled smartphone on the center of the
14 Wireless charging pad.
Compatible Products for Wireless Charging: iPhone 11/11 Pro/11 Pro Max/X/XS/XS Max/XR/8/8 Plus; AirPods Pro, AirPods; Samsung Galaxy S10/9/8/7/6 series, Note 10/9/8/7/5 series; LG V50/V40/V30 series, G8/G7/G6 series; Google Pixel 4/4 XL/3/3 XL, and other Qi-enabled smartphones/tablets and accessories.
**
PMA wireless charging is not supported.
WIRELESS CHARGE INDICATOR
26 Wireless Charging Indicator is displayed on the top right corner of the display. Refer to the status indications below:

  1.  Off : Standby Mode
  2. On : Charging
  3. Blinking : Abnormal
    *If the charging indicator blinks:
    – Check if your device supports Qi wireless charging
    – Place your device in the center of the 14 Wireless charging pad
    – Remove any protective cases containing magnets, metal, or materials thicker than 0.12″ (3mm)

USB CHARGING PORT

  1. To charge other devices such as a smartphone or tablet, connect one end of the USB charging cable (not included) to the 29 USB charging port on the back of the main unit.
  2. The Morning Call 6Q cannot access the content of the connected device.
  3. The USB charging port is compatible with most smartphones, tablets, portable speakers, wireless headphones, wearables, etc.

BATTERY BACKUP OPERATION

****THE BACKUP BATTERY WILL NOT OPERATE THE CLOCK

  1. Morning Call 6Q is equipped with a memory system that can be powered with two (2) AAA batteries (not included). The power failure protection circuit will not operate unless the battery is installed.
  2. The backup battery will save all previously programmed settings when normal household power is interrupted The backup battery will not operate the unit’s normal functions.
  3. Normal operation will resume after the power is restored.

INSTALLING THE BATTERY

**** The backup battery is NOT a secondary source of power. The function acts as a memory saver for your settings in the case of power disconnection. It is recommended to replace the battery at least once a year.

  1. Remove the 3SPECIFICATIONS
    Tuner Range FM: 87.5 — 108 MHz Number of Preset Radio Stations 20 AC Power Adapter
    Input: AC 100-240V, 50/60Hz
    Output:DC 12V/1.5A
    Charging Output Wireless: 7.5W/10W USB: 5V/1 A
    COMPLIANCE WITH FCC REGULATION
    0 Battery Compartment Cover.

  2. Place two (2) AAA batteries (not included) according to the polarity marked inside.

  3. Place the battery compartment cover to its original position.

****In order to save your settings, do NOT disconnect the power adapter when replacing your batteries.

SPECIFICATIONS

Tuner Range FM: 87.5 — 108 MHz
 Number of Preset Radio Stations  20
 AC Power Adapter  Input: AC 100-240V, 50/60Hz Output :DC 12V/1.5A
Charging Output  Wireless: 7.5W/10W USB: 5V/1 A

COMPLIANCE WITH FCC REGULATION

FCC Warning
This device complies with part 15 and part 18 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Increase the separation between the equipment and any other radio device.
  2. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

LIMITED WARRANTY

HAT IS COVERED?
Luv Creative Technology (“iLuv”) warrants, to the original purchaser, that its products will be free from defects in materials, parts, and workmanship for the periods designated in each Product. The Warranty ipegins on the date of product purchase and covers a Period of two years for products purchased in the European Union, and one year for products Purchased in other countries (including the United States and Canada), iLuv can exercise the option, during any warranty service, to replace your product with a new or remanufactured unit, equivalent to tour original purchase. For information on proper installation, operation and use consult the manual supplied with the product. If a replacement manual is required, visit our website, www.iLuv.com to download a manual.
FCC NOTICE (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Note: Changes or modifications not expressly 4pproved by the party responsible for compliance could void the user’s authority to operate the equipment.
EXCLUSIONS
This Warranty does NOT apply if the serial number is altered or removed. It does not cover cosmetic damage, antenna damage or loss, damage to AC power cords, cabinets, headbands, ear-pads, or damage due to power line surges, connection to an improper voltage source, the use of improper settings, general misuse, mishandling or improper application, accidents, acts of God, repairs attempted by an unauthorized service agent, or damage incurred while the product is being returned to iLuv. If the product was purchased outside the United States, please find an authorized distributor as listed on our website: www.iLuv.com
OBTAINING WARRANTY SERVICE
Customers must obtain a Customer Return Authorization number (CRA) on our website, www.iLuv.com (EXPRESS CUSTOMER SUPPORT) to obtain a ticket. Fill out the online form including the product’s Date of Purchase, its Model Number, a brief description of the problem, and your daytime telephone number, or customers in the United States and Canada may contact our Customer Service Department at 866-807-5946 if the problem appears to be related to a defect in material or workmanship.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This 1 warranty gives you specific legal rights and you may also have other rights, which vary from state to state and country to country. INSTRUCTIONS ON ENVIRONMENT 1 PROTECTION
Do not dispose of this product in the usual household garbage at the end of its life cycle; bring it to a collection point for the recycling of electrical and 1 electronic appliance. This symbol on the product means the instructions for use or the packing will inform about the methods for disposal. The materials are recyclable as mentioned in its marking. By recycling, material recycling, or other forms of re-utilization of old appliances, you make an important contribution to protect the environment. Please inquire at your local community administration for the authorized disposal location.

Designed by iluv in New York
iLuv Creative Technology
2 Harbor Park Drive Port Washington, NY 11050
CUSTOMER SUPPORT
if you have any questions or need support,
please contact us by visiting http://support.iLuv.com or call our customer service department at
1-866-807-5946

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals