iLuv SmartShaker 3 Vibration Bed Shaker Bluetooth Alarm User Manual
- June 6, 2024
- iLuv
Table of Contents
iLuv SmartShaker 3 Vibration Bed Shaker Bluetooth Alarm
WHAT YOU NEED
► Any device with iOS10 / Android 5.0 or above
► A power charger or power bank
WHAT’S INCLUDED
DEVICE SETUP
-
Charge the SmartShaker 3
Connect the charging cable to the SmartShaker 3 and a USB-C power charger.
The 4 LEDs on the SmartShaker 3 will continuously blink white indicating that the device is charging.
The 4 LEDs will stop blinking once charging is complete. -
Install the SmartShaker 3 App
|
|
---|---|---
Search and download “SmartShaker 3” on the Apple App Store or Google Play
Store.
** Please do not install SmartShaker+ App
- Turn on Bluetooth on your mobile device.
- Launch the SmartShaker 3 App and follow the instructions.
DEVICE INTRODUCTION
Snooze Button
- Press once to check battery
- Press once to snooze alarm if alarm is active
On/Off Switch
- Off: Disable alerts for all incoming calls, messages and alarms
- On : Enable alerts for all incoming calls, messages and alarms
Reset Hole
- Reset for SmartShaker 3
USB-C Charging Port
- Connected to any charging adapter/ Power bank/ PC with 5V 1 A output
LED
APP OPERATIONS
DEVICE SPECIFICATION
-
Dimension and weight
Dimensions: 3.9″X3.9″X1.3″ (100mm X 100mm X 34mm)
Weight: 170g -
Compatibility
iOS devices with iOS 10 or above
Android devices with Android 5.0 or above -
Connectivity
Bluetooh 5.2 -
Frequency, power and coverage,
Bluetooth frequency: 2402 – 2480 MHz
Max output power: 2.SmW (4 dBm)
Bluetooth coverage: Up to 15 m ( 45FT) -
Coverage can be reduced by thick walls and large objects
-
Power and battery
Battery power: 1 x 1500mAh Li-ion Polymer Battery
Power consumption:
Active with strong vibration < 900mA Idle position < 200 μA
Operating time: Up to 14 days per charge
Charging time: Up to 1 hour45 minutes@5V 1000 mA -
Cables and connections
Cable length: 1 m ( 3.3′ )
Contacts: USB-A to USB-C -
Environmental requirements
For indoor use only
Temperature: 15° – 35°C, 59° – 95°F
Relative humidity: 5% – 95% (non-condensing) -
What’s include
SmartShaker 3 Main unit
Charging cable
Manual
FAQS
-
In the app stores which app is for SmartShaker 37
SmartShaker 3, not SmartShaker+ -
How long will the SmartShaker 3 continue to vibrate if left untouched?
5 minutes. -
How can I snooze the alarm?
Press the snooze button on the device or press the snooze button on the App. -
Can I customize the timing for the snooze interval?
The default is 9 minutes however you can edit the timing by going to Menu -> Time Setting -> Snooze Interval. -
How can I stop the alarm?
Slide the Alarm button to off or press the stop button on the App. -
How can I enable alerts for incoming calls?
Go to Menu -> Alert Setting and then toggle the ” Alert for phone calls “. Please make sure the SmartShaker3 is on. -
How can I enable alerts for incoming messages?
Go to Menu -> Alert Setting and then toggle the “ Alert for SNS Messages “. Please make sure the SmartShaker3 is on.
TROUBLESHOOTING
-
My SmartShaker 3 isn’t responding.
Plug the SmartShaker 3 to a power source to make sure the device is fully charged. You can check the battery level by pressing the snooze button. -
My app isn’t connecting to my SmartShaker 3.
i. Make sure Bluetooth is enabled on your phone.
ii. Place the SmartShaker 3 and the connected phone closely together.
If this cannot help, try below.
i. Force close the SmartShaker 3 App.
ii. Toggle Bluetooth on your mobile.
iii. Reset your SmartShaker 3.
iv. Open your app again.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, If not installed and used In accordance with the inst ructions, may cause harmful interference to radio communications. However, there is no guarantee that Interference will not occur In a particular Installation. If this equipment does cause harmful interference to radio or television recepti on, which can be determined by turning the equipment off and on, the user ls encouraged to try to correct the interference by one or more of the followling measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful Interference, and
(2) this device must accept any Interference received, including
Interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
Hereby, iluv Creat.lve Technology declares that the radio equipment type SmartShaker 3 is In compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity Is available at the follow internet address :www.iluv.com
TROUBLE SHOOTING: When the battery is completely drained while not in use for a long period of time, try charging it a few times as It will resume its normal charging process. Restart the charging process if the charging indicator does not respond or is turned off after a few minutes.
ONE YEAR LIMITED WARRANTY
EUROPEAN UNION TWO YEARS LIMITED WARRANTY
Documents / Resources
| iLuv
SmartShaker 3 Vibration Bed Shaker Bluetooth
Alarm
[pdf] User Manual
SMSHAKER3, ATL-SMSHAKER3, ATLSMSHAKER3, SmartShaker 3 Vibration Bed Shaker
Bluetooth Alarm, Vibration Bed Shaker Bluetooth Alarm, Bluetooth Alarm, Alarm
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>