FALCON RIDGE HO-P10005-SDKFM01 Honda Pioneer 1000 5 Soft Door Kit Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
HO-P10005-SDKFM01 Honda Pioneer 1000 5 Soft Door Kit
Instruction Manual
HO-P10005-SDKFM01 Honda Pioneer 1000 5 Soft Door Kit
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature prior to installation.
- Carefully open the carton and remove the enclosure on a large flat surface that is clean and free of dirt.
- Check over the parts included in the carton with the parts list shown below:
Adhesive Velcro Hook Strips:
Adhesive Velcro Hook Strips:
“ “ “ “
“ “ “ “
“ “ “ “
“ “ “ “| Soft Front Doors
16 each————3″
2 each————5″
2 each————6″
2 each————8″
---|---
Snap Studs| 11 each (1 extra)
| Soft Rear Doors
“ “ “ “
“ “ “ “
“ “ “ “| Soft Rear Doors
12 each————3″
2 each————2″
2 each————9″
Snap Studs| 9 each (1 extra)
Adhesive Velcro Hook Strips:
“ “ “ “
“ “ “ “| Middle Rear Window
8 each————3”
1 each————47”
If any parts are damaged or missing please contact customer service at
606-845-7439.
The cab for your Honda Pioneer 1000 5 is made up of 6 different components
that work together to enclose your vehicle. Install the cab in the following
order.
- Soft Front Doors
- Middle Rear Window
- Soft Rear Doors
- Rear Rear Window
Soft Front Doors:
-
Begin by placing the 5″, 6″ and 8″ adhesive Velcro strips in their place. The following pictures show where they go.
-
Next, hold the door up to the frame and attach these spots then continue attaching it using the double-sided Velcro strips sewn perpendicular to the edge of the door. At each of the double-sided strips take one of the 3″ adhesive Velcro strips and adhere it to the inside of the frame. Then wrap the double-sided strip around it so that the adhesive strip holds it firmly in place. The following diagrams show how it should look.
-
Once all the Velcro is attached securely take the snap studs and screw them into the plastic doors.
NOTE: It helps to put the snap studs into the sockets in the canvas first. Then one at a time pushes the screw into the plastic hard enough so that a mark is left behind. Pull the snap stud back out of the door and screw it into the plastic where the mark was made. Snap the door in place and move on to the next one. See the photo below.
-
To use the door simply unzip it and pull down it to release the magnets then reach in and open the plastic door. Once in lift the door up so the magnets attach to the bar and zip closed.
Soft Rear Doors:
-
Begin by placing the 2″ adhesive Velcro strip in the top front corner on the flat surface shown in the photo below.
-
Then take the Rear Door and zip it to the Middle Rear Window. This ensures the door is properly placed. Then attach the top front corner to the Velcro. See photo below.
-
Next, use the 9″ adhesive Velcro strip for the tab on the top rear section of the door. See photo below.
-
Then attach the 3″ adhesive strips for the double-sided strips sewn around the edge the same way you did for the front doors.
-
Once all the Velcro is attached securely take the snap studs and screw them into the plastic doors.
NOTE: It helps to put the snap studs into the sockets in the canvas first. Then one at a time pushes the screw into the plastic hard enough so that a mark is left behind. Pull the snap stud back out of the door and screw it into the plastic where the mark was made. Snap the door in place and move on to the next one. See photo below.
Cleaning and Storage Recommendations:
-
Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage.
-
It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory.
On a large, clean, and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter.
Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing. -
A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if the additional hook and loop sets are needed, they can also be ordered.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from the date the item is received. You MUST package the product
exactly as it was originally packaged from the factory to get a full refund
for the product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive a refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors, you must first call them and see
what their return policy is. Once your item reaches our production facility,
our customer satisfaction team will inspect your item to ensure unused,
factory-new condition. NOTE: All windshields must be returned with the
original protective film intact and not removed. Do NOT REMOVE if you have any
intentions of returning the item. Refund/ replacement of a windshield will
only be processed on items with original protective film or if the windshield
is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered, or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, a credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping costs will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops, and/or windshield due to defects of the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>