01B0 Cisco Room Kit Pro Precision 60 Installation Guide
- June 14, 2024
- Cisco
Table of Contents
01B0 Cisco Room Kit Pro Precision 60
Box contents
- a. Power adapter and cable for Precision 60
- b. Ethernet cable for Touch 10 / Room Navigator
- c. Antennas for Codec Pro
- d. Power cable for Codec Pro *
- e. Rack ears for Codec Pro (optional)
No power cord option for Codec Pro: When the optional power cord is not ordered with the system, the customer is responsible for selecting the appropriate power cord to be used with this product. Using a non-compatible power cord with this product may result with electrical safety hazard. For orders to be delivered to Argentina, Brazil and Japan, appropriate power cord must be ordered with the system.
- Rating of the power cable: 10 A, 250 V
- Power connector: EL 701B (IEC 60320/C13)
Can be ordered separately
- Microphone(s) : Cisco table- or ceiling microphone is recommended.
- Cables : For set-up, the system may require more HDMI and Ethernet cables depending on the needs. We recommend that you order the cables from Cisco. HDMI cables are required for screens and presentation sources. We recommend to only use certified HDMI cables: High Speed HDMI 1.4b cables for the presentation sources and Premium High Speed HDMI cables for the screens. Ethernet cables are required for camera control and for connecting the codec to the network (not required if you use the wireless LAN).
Safety and mounting hardware
The wall and mounting hardware must be able to safely support the product. The wall mounted system must be installed by qualified personnel, in accordance with state and local building regulations.
Ventilation
Do not block any ventilation openings on the codec. Minimum 10 cm / 4 ” free
space in front and rear side of the unit. Minimum 4.5 cm / 1.7 ” free space
below the codec and an adjacent rack-mounted component.
Mount the codec in a rack (optional)
You can mount the rack ears so that the connector panel is facing forward or backward.
-
Connect the codec cables
-
Connect the antennas to the codec
-
Connect the Precision 60 camera cables
Always use the supplied power adapter for the Precision 60 camera. Use an Ethernet cable when connecting the camera control cable between the camera and codec. Using a VISCA cable will cause severe damage to the camera. If you use a coaxial cable for video, you will need a BNC to HD-BNC cable or a BNC to HDBNC adapter to connect the Precision 60 (BNC) to the Codec Pro (HD-BNC). -
Turn on the codec
- Power (100-240 VAC, 50/60 Hz)
- Always use the provided power cable. Or use a power cable that meets the requirements of the power specification of the codec.
- Keep the power plug and outlet easily accessible in case you need to disconnect the device from power.
- This device is designed for connection to TN and IT power systems.
- Network connectivity:
- Use either Ethernet LAN or Wi-Fi. Non-radio devices, which have the letters ‘NR’ in their product identifier (PID), don’t support Wi-Fi.
-
Complete the software setup
-
Turn on the screen. See the user documentation for the screen if HDMI input must be set manually.
-
The system powers up automatically. If the system doesn’t power up, check the power switch on the codec and the camera.
-
When you see the Welcome screen, follow the instructions to complete the setup.
-
We recommend that you upgrade the software on your Codec Pro before putting it to use. See the Administrator Guide for the codec: https://www.cisco.com/go/room-docs
Cisco Codec Pro
- A. Antenna connector
- B. 6 × Line output (Euroblock, 3.5 mm)
- C. 8 × Microphone/Line input (Euroblock, 3.5 mm)
- D. GPIO port (Euroblock, 3.5 mm)
- E. COM port (Euroblock, 3.5 mm)
- F. Antenna connector
- G. Ground (Protective earth)
- H. Main power input (1.3 – 0.6 A, 100-240 V ac, 50/60 Hz)
- I. 2 × HDMI output with audio and video (Connector 1-2), 4Kp60
- J. HDMI output with audio and video (Connector 3), 4Kp30
- K. 2 × Camera input (HDMI, Connector 1-2), 1080p60
- L. 3 × HDMI input with audio and video (Connector 3-5), 4Kp30
Cisco TelePresence Precision 60 Camera
- A. Video (3G-SDI ), 1080p60 *
- B. Not in use
- C. HDMI output, 1080p60
- D. Factory reset
- E. Security lock slot
- F. Power input (12 Vdc, 2.5 A)
- G. Camera control (Ethernet)
Visit these websites to learn more about your device.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third- party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Cisco Systems Inc.
Corporate Headquarters
170 West Tasman Dr.
San Jose, CA 95134
USA
https://www.cisco.com/go/offices
Documents / Resources
|
CISCO 01B0 Cisco Room Kit Pro Precision
60
[pdf] Installation Guide
01B0 Cisco Room Kit Pro Precision 60, 01B0, Cisco Room Kit Pro Precision 60,
Room Kit Pro Precision 60, Kit Pro Precision 60, Pro Precision 60, Precision
60
---|---
References
- Cisco Room Series - Cisco
- Cisco Project Workplace | Seamless Collaboration
- Cisco Trademarks - Cisco
- Cisco Room Series - Cisco
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>