FALCON RIDGE KY-UXV450-WD05 Kymco UXV 450 Full Aero-Vent Lexan Windshield Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
FALCON RIDGE KY-UXV450-WD05 Kymco UXV 450 Full Aero-Vent Lexan Windshield
2515 Bypass Rd. Flemingsburg, KY 41041 606-845-7439
Instructions for Installation and Care of Kymco UXV 450 Full Aero-Vent Lexan Windshield
KY-UXV450-WD05
NOTICE: Please check contents of package for any damage and make sure all parts fit correctly and you are happy with the product before removing protective film. Once the film is removed you cannot return the product for a full refund.
INSTALLATION
Be sure to read these instructions thoroughly before opening and installing the Kymco UXV 450 Full Aero-Vent Lexan Windshield.
-
Check over the parts included in the cartons with the parts list shown below:
- 1 ¾” Loom Clamps 8 each
- 1” Stainless Steels Bolts 13 each
- Stainless Steel Washers 17 each
- Stainless Steel Lock Nuts 4 each
- Plastic Thumb Nuts 9 each
- Plastic Slide Fasteners 4 each
- 54″ Rubber Gasket 1 Piece
- Lexan Windshield 1 Piece
- Lexan Brac e 1 Piece
- Sliding Vent Panel 1 Piece
If any parts are damaged or missing please contact customer service at 606-845-7439.
-
After pulling it out of the box, find a clean area to lay it down and install the hardware. Next take the three rubber gasket pieces and starting at one end firmly place along entire bottom hood contour of the windshield. Ensure that the gasket is seated fully home on the bottom edge. You will need to peel back the protective film about 1†from the edge to install the gasket. If you leave the bulk of the protective film on while installing you will avoid scratching the windshield during assembly. See photo below. Photos are not exact representation of a Kymco UXV 450 and are for reference only
-
3. Next you will take the Aero-Vent slider and attach it to the inside of the windshield. The photos below show the proper installation of the Vent Slider.
-
Next take the bent Lexan brace and install it on the outside of the windshield. The bend will be above the bolts when installed. Please refer to the diagrams below.
-
5. Now you are ready to place the windshield on the vehicle and attach to the roll cage. There will be two on each side and two across the top of the windshield. The diagram below shows the proper placement sequence of the hardware. Use the 1 bolts for this application. Install each one loosely at first; after you have centered the windshield and are satisfied with exact placement, then you may snug the thumbnuts appropriately.
-
Enjoy, and remember- when cleaning the windshield do so gently at first with warm water and mild detergent to dislodge any grit that may scratch the Lexan. After rinsing and drying with a soft cloth (we recommend microfiber), you may then polish the windshield with an appropriate commercially available plastic polish, also available from Falcon Ridge. This will ensure many seasons of clarity and keep scratching and swirling to a minimum. Never use cleaners such as Windex that contain ammonia as doing so may adversely affect the windshield.
-
Transporting or trailering your UTV with the windshield installed is not generally recommended. It is best to remove the windshield before transporting your UTV.
Thank You for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within 30 days from the date the item is received. You MUST package the product exactly as it was originally packaged from the factory to get a full refund for the product! The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the windows on top of each other with the canvas folded in between and the paper (if available) on both sides of the windows. All returned products will be inspected upon arrival at the production facility and must be in unused, factory-new condition to receive refund – a 25% restocking fee will apply. If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number, use our preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying the shipping to return the item.) Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory-new condition.
NOTE: All windshields must be returned with the original protective film intact and not removed. Do NOT REMOVE if you have any intentions of returning the item. Refund/ replacement of a windshield will only be processed on items with original protective film or if the windshield is defective. Items must be properly packaged in the original shipping carton to protect them during transit and ensure your returned item arrives back factory fresh, and in new resalable condition (any returned items that have been used, altered or damaged in any way will not be subject to a refund.) All contents including instruction manuals, accessories, hardware, Velcro, etc. must be included in your return shipment. Only items in OEM factory new condition will be approved. Once returned items are received, credit will be issued to the original credit card/ payment method used for the purchase. Outbound shipping and return shipping costs will not be refunded. Please allow 4 to 6 weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty. 30 Day Warranty which includes and is not limited to
replacing the enclosure, tops, and/or windshield due to defects in the
product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>