FALCON RIDGE PO-RZR-DRW01 Polaris RZR 800 900 Soft Door Rear Window Combo Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
2515 Bypass Road Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of Polaris RZR 800/900 Soft Door
Rear Window Combo
PO-RZR-DRW01
CAUTION: Do not smoke inside the cab or expose the enclosure to direct
flames. Product is FLAMMABLE.
PO-RZR-DRW01 Polaris RZR 800 900 Soft Door Rear Window Combo
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature prior to installation.
- Carefully open the carton and remove the rolled up Cab Enclosure on a large flat surface that is clean and free of dirt or other material that may soil or scratch the windows of the Cab.
- This cab enclosure is made up of 3 different panels that all come together to fully enclose the sides and rear of the vehicle. You may put on different pieces or leave other pieces off to create the enclosure that best meets your needs.
- Check over the parts included in the carton with the parts list shown below:
If any parts are damaged or missing, please contact customer service at606-845-7439.
For these instructions we will be installing the entire enclosure. This will cover every piece so if you should want to install just parts of the enclosure these instructions should be sufficient.
The order of installation will be as follows:
Side Door Panels
Rear Window
SOFT DOORS:
4. Before installing the cab enclosure, you will need to remove the seats and
set them aside.
5. Begin installation by hanging the Door Panels from the top by using the 3″
adhesive Velcro strips as shown in the photos below:
6. Begin installation of the Door Panels by hanging them from the Double-
Sided Strips along the top of the doors. Hold the door up and mark where the
each strip is and wrap a 3″ adhesive strip around the roll cage. Now hang the
door up and it will be in place to install the rest of the Velcro for the
door. See Photo Below:
7. Now move around the door and attach the remaining Velcro strips in the
same manner. Down the front of the door place the edge of the door against the
side of the windshield and run the Velcro strips under it with the 3″ adhesive
Velcro on the inside of the roll cage.
8. The rear of the door panel has two double-sided Velcro tabs that attach to
the rear bar. For these you will take the two 20″ adhesive Velcro strips and
attach them down the rear bars facing the rear of the vehicle. Then attach the
tabs to the bar as shown in the photo on the next page.
9. Once the upper portion of the doors is in place it’s time to place the
Velcro, and snaps around the rear portion of the doors.
10. Start with the bottom rear side of the door and attach the 28″ adhesive
Velcro down the sides of the vehicle to match up with the Velcro sewn along
the edge as shown in the photo below.
11. Next take the front of the door and tuck it inside the vehicle. There are three snaps that will go on the inner panel. NOTE: it helps to place the screw snaps into the sockets on the cabs first, then starting at the top one, push them into the plastic so a small dimple is left behind. Then pull the screw snap back out and screw it into the plastic where the mark was made. See photo below
12. Next do the same for the snaps along the bottom of the door as shown in the photo below.
REAR WINDOW:
13. Begin installation of the Rear Window by hanging it from the top bar
first. Take the 36″ adhesive Velcro strip and attach it to the top bar facing
to up towards the sky. The photo below shows where to install the Velcro.
14. The sides of the Rear Panel will attach to the outside of the double-
sided tabs that hold the rear of the door panels as shown below. See photo in
section 7e.
15. Finally take the 42″ adhesive Velcro strip and attach the bottom of the
rear window to the inside of the rear cargo area. See Photo Below:
Cleaning and Storage Recommendations:
- Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll for storage.
- It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean, and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at a normal room temperature. It is best not to expose the Cab to either extreme hot or cold temperatures when storing.
- A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if additional hook and loop sets are needed, they can also be ordered.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from date item is received. You MUST package the product exactly as it
was originally packaged from the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors, you must first call them and see
what their return policy is. Once your item reaches our production facility,
our customer satisfaction team will inspect your item to ensure unused,
factory-new condition. NOTE: All windshields must be returned with the
original protective film intact and not removed. Do NOT REMOVE if you have any
intentions of returning the item. Refund/ replacement of a windshield will
only be processed on items with original protective film or if the windshield
is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered, or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping cost will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of Falcon Ridge’s Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops, and/or windshield due to defect of the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>