FALCON RIDGE PO-08RANGER-RW01 Polaris 08 Ranger Soft Rear Window Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of
Polaris 08 Ranger Soft Rear Window
PO-08RANGER-RW01
CAUTION: Do not smoke inside the cab or expose the enclosure to direct
flames. The product is FLAMMABLE.
Be sure to read these instructions thoroughly before opening and installing
the rear window. The installation is best done when the ambient temperature is
70°F or warmer. If installed in cold weather, warming the adhesive Velcro
strips before installation is recommended.
- Carefully open the carton and unroll the enclosure onto a large flat surface that is clean and free of dirt or other material that may soil or scratch the vinyl window.
- Check over the parts included in the carton with the parts list shown below:
Velcro hook strip| 1 each| 50” long
---|---|---
Velcro hook strips| 1 each| 40” long
Velcro hook strip| 10 each| 3” long
Enclosure| 1 each
If any parts are damaged or missing please contact customer service at 606-845-7439.
-
Lift the bed and begin by applying the 40” adhesive Velcro strip across the top of the rear of the roll cage. Attach the corresponding sewn-on Velcro tab to this, then pull the rear window down moderately and place the 55” Velcro strip along the bottom of the roll cage across the metal strip there. Clean the areas of any dirt or grease before applying adhesive strips. Apply the sewn-on Velcro tab to the adhesive Velcro strip.
-
Next work your way to the sides. Pull the enclosure moderately and evenly to both sides; go one side at a time. Note the locations of the sewn-on Velcro and apply the corresponding adhesive Velcro strips to the vertical roll cage tubes on both sides of the rear of the cab. It is important to pull each side evenly. Do not pull excessively to another side, or the fitment will not be optimal. Apply the 12”, and attach the corresponding Velcro tabs. Finally, the 6” adhesive strips are for the double-sided 1” wide wraparound straps at the top of the enclosure. After you have the top, bottom, and sides attached to their corresponding adhesive Velcro strips on the roll cage, moderately all the top corners up and over the top of the roll cage, and make note of where the wraparound straps contact the roll cage. Apply the remaining 6” adhesive strips to where the wraparound straps are located and wrap the straps around to secure the top corners. Congratulations – you are now finished with the installation.
Cleaning and Storage Recommendations:
- Before removing the enclosure for storage, make sure it is clean and dry, to prevent soiling the textile and scratching the clear vinyl windows. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Let the enclosure dry thoroughly before attempting to roll it for storage.
- It is important that the enclosure be rolled up for storage rather than folding. Folding will cause undesirable creasing of both the enclosure textile and the clear vinyl windows. Carefully roll up the enclosure similar to the way it was when it was packed at the factory. Put the rolled enclosure back into the carton for storage at normal room temperature. It is best not to expose the enclosure to either extremely hot or cold temperatures when storing.
- A special cleaner/conditioner is available from Falcon Ridge that will greatly increase the service life of the cab enclosure. If needed, additional hook and loop sets are available, as well as other spare parts and hardware. Contact Falcon Ridge for information.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from the date the item is received. You MUST package the product
exactly as it was originally packaged from the factory to get a full refund
for the product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive a refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is effective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors’, you must first call them and
see what their return policy is. Once your item reaches our production
facility, our customer satisfaction team will inspect your item to ensure
unused, factory-new condition.
NOTE: All windshields must be returned with the original protective film
intact and not removed. Do NOT REMOVE if you have any intentions of returning
the item. Refund/ replacement of a windshield will only be processed on items
with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject to a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, a credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping costs will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty. 30 Day Warranty which includes and is not limited to
replacing the enclosure, tops, and/or windshield due to defects in the
product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase. 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>