Barthelme 66000771 Remote Control Instruction Manual
- June 5, 2024
- Barthelme
Table of Contents
LED Solutions
INSTRUCTION MANUAL FOR
REMOTE CONTROL
Item.-No. 66000771 –
1-channel remote control
(suitable for the control unit 66000770)
PLEASE READ CAREFULLY AND ARCHIVE!
INTRODUCTION
Since this remote control is an accessory of the 66000770 control unit, it can
only be used in conjunction with this control unit. The operating instructions
of the control unit must be observed.
The outputs of the control unit are controlled depending on the use of the
coupled remote control/touch panel. This remote control is a 1-channel device,
for monochrome applications. Up to four zones can be controlled separately per
remote control.
Each control unit can be paired with up to eight different remote controls.
Within a network, all colors can be synchronized automatically. The range
depends strongly on the spatial conditions; in an open field, up to 50 meters
are possible, indoors a reliable operation of over 20 to 30 meters is normally
possible without any problems.
INTENDED USE
The remote control allows you to adjust colors or to select effects.
It uses a button and a touch-sensitive round slider.
The remote control uses a radio frequency that is license-free in the EU,
Switzerland, Norway, and Iceland.
TECHNICAL DATA
Operating voltage: 4.5 V
DC Batteries: 3x 1.5 V (AAA batteries)
Protection class: III
Dimensions (L/W/H): 120 / 55 / 17 mm
Ambient temperature: 0 °C to the max. + 40 °C
Relative air humidity: 8 % to 80 %
Wireless frequency: 869.5 MHz (license-free in the EU, Switzerland,
Norway, and Iceland).
Indoor range: 20 to 30 meters Protection class: IP 20
SAFETY INSTRUCTIONS
In case of improper operation, modification of the device, or damage to property or persons caused by improper handling or non-observance of the safety instructions, we do not assume any liability and the warranty claim expires completely.
OPERATION
Only operate the product when it is functioning properly. In the event of a fault, switch the product off immediately and do not operate it again until it has been checked by a qualified electrician. This is the case if:
- visible damage occurs
- the product does not work properly
- there is smoke, fumes, or audible crackling noises
- overheating can be detected
5.1 COMMISSIONING
Insert suitable batteries (3x 1.5 V, AAA batteries) into the remote control (back) and pair it with the control unit.
1. STEP 1:
Wire the RF receiver according to the wiring diagram (please refer to the
instructions of the RF receiver with which you want to pair the device)
STEP 2:
Press the ON/OFF button to activate the remote control
RF-LED Receiver
Learning Key
STEP 3:
Press the „learning key“ on the RF receiver or switch on the receiver
three times in succession to set it to the connection status
STEP 4:
Select and press a zone number (e.g. zone 4)
STEP 5:
Touch the round slider. When the LED lights connected to the wireless receiver
flash once, it means that the receiver is successfully connected to Zone 4.
3.
IF
SEVERAL CONTROL UNITS ARE USED, THIS PROCEDURE MUST BE PERFORMED ON EACH
CONTROL UNIT.
5.2 KEY ASSIGNMENT / FUNCTION
- Press and hold to increase/decrease light intensity
- 25 % brightness
- Press to turn all zones on / off
- 75 % brightness
- Display: Indicates the status of the remote control
- Touch the round slider (color wheel) to select the brightness level
- Zone numbers: Click to select the zone(s). Press and hold to turn the corresponding zone on or off
- 50 % brightness
- 100 % brightness
- Press and hold to save the colors.
Press again to recall the saved colors
5.3 SAVING THE CURRENT SETTINGS
STEP 1:
Press the ON/OFF button to activate the remote control
STEP 2:
Select one or more connected zone numbers (e.g. Zone 4) and press it.
STEP 3:
Touch the round slider (color wheel) or press the other buttons to select the
desired scene.
STEP 4:
Press and hold any scene button from S1 to S3 (e.g. S3) , and the LED
lights connected to the RF receiver will flash once, which means the
color/scene has been saved successfully
5.4
RECALL THE SAVED SETTINGS
STEP 1:
Press the ON/OFF button to activate the remote control
STEP 2:
Select one or more connected zone numbers (e.g. Zone 4) and press it.
STEP 3:
Press any scene button from S1 to S3 (e.g. S3) to recall the saved scene.
SCOPE OF DELIVERY AND ACCESSORIES
Each remote control is supplied with (these) instructions. It is part of the
scope of delivery for the device and must be handed over to the end-user.
Important: All instructions for Barthelme products can be downloaded from
the Internet at www.barthelme.de. Please check for
updates before use!
SIMPLIFIED EU DECLARATION OF CONFORMITY: Barthelme hereby declares that
wireless equipment type 66000771 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following Internet address:
www.barthelme.de/shared/download/CE_declaration_66000771.pdf
NOTES
…………………………….
CONTACT
Josef Barthelme GmbH & Co. KG
Oedenberger Str. 149
90491 Nürnberg | Germany
T: +49 911 42 476 0
E: info@barthelme.de
www.barthelme.de
VERSION 03|2022
SUBJECT TO TECHNICAL CHANGES
Documents / Resources
|
Barthelme 66000771 Remote
Control
[pdf] Instruction Manual
66000771, Remote Control, 66000771 Remote Control
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>