Barthelme 66000775 5-Channel Remote Control Instruction Manual
- June 8, 2024
- Barthelme
Table of Contents
66000775 5-Channel Remote Control
Instruction Manual INSTRUCTION MANUAL
66000775 5-Channel Remote Control
FOR REMOTE CONTROL
Item.-No. 66000775 – 5-channel remote control
(suitable for the control unit 66000770)
PLEASE READ CAREFULLY AND ARCHIVE!
INTRODUCTION
Since this remote control is an accessory of the 66000770 control unit, it can
only be used in conjunction with this control unit. The operating instructions
of the control unit must be observed.
The outputs of the control unit are controlled depending on the use of the
coupled remote control/touch panel. This remote control is a 5-channel device,
for RGBW/TW applications. Up to four zones can be controlled separately per
remote control.
Each control unit can be paired with up to eight different remote controls.
Within a network all colors can be synchronized automatically. The range
depends strongly on the spatial conditions; in the open field up to 50 meters
are possible, indoors a reliable operation over 20 to 30 meters is normally
possible without problems.
INTENDED USE
The remote control allows you to adjust colors or to select effects.
It uses a button and a touch-sensitive round slider.
The remote control uses a radio frequency that is license-free in the EU,
Switzerland, Norway and Iceland.
TECHNICAL DATA
Operating voltage: 4.5 V DC
Batteries: 3x 1.5 V (AAA batteries)
Protection class: III
Dimensions (L/W/H): 120 / 55 / 17 mm
Ambient temperature: 0 °C to max. + 40 °C
Relative air humidity: 8 % to 80 %
Wireless frequency: 869.5 MHz (license-free in the EU, Switzerland, Norway and
Iceland).
Indoor range: 20 to 30 meters
Protection class: IP 20
SAFETY INSTRUCTIONS
In case of improper operation, modification of the device, or damage to property or persons caused by improper handling or non-observance of the safety instructions, we do not assume any liability and the warranty claim expires completely.
OPERATION
Only operate the product when it is functioning properly. In the event of a fault, switch the product off immediately and do not operate it again until it has been checked by a qualified electrician. This is the case if:
- visible damage occurs
- the product does not work properly
- there is smoke, fumes, or audible crackling noises
- overheating can be detected
5.1 COMMISSIONING
Insert suitable batteries (3x 1.5 V, AAA batteries) into the remote control
(back) and pair it with the control unit.
STEP 1:
Wire the RF receiver according to the wiring diagram (please refer to the
instructions of the RF receiver with which you want to pair the device)
STEP 2:
Press the ON/OFF button to activate the remote control RF-LED Receiver
Learning Key
STEP 3:
Press the „learning key“ on the RF receiver or switch on the receiver three
times in succession to set it to the connection status
STEP 4:
Select and press a zone number (e.g. zone 4)
STEP 5:
Touch the round slider. When the LED lights connected to the wireless receiver
flash once, it means that the receiver is successfully connected to Zone
4
IF SEVERAL CONTROL UNITS ARE USED, THIS PROCEDURE MUST BE PERFORMED
ON EACH CONTROL UNIT.
5.2 KEY ASSIGNMENT / FUNCTION
- Touch the slider to turn on the two-color LED lighting and select the color temperature
- Press and hold to increase or decrease the light intensity of the RGB channels
- Press to turn on/off all zones
- Touch the round slider (color wheel) to select any color
- 4 zones: Press the corresponding button to select the desired zone. Press and hold this key to switch this zone on or off
- Press keys for the RGB channels to switch the corresponding zone on and off. Press and hold to switch the corresponding zone on or off again
- Press and hold to save color/scene/mode. Press to recall the saved colors/scenes or modes again
- Press to recall the program in four different modes: Jump, Flash, Fade and Strobe
- Program setting button: LED lights connected to the receiver will flash once, then touch the round slider (color wheel) to select 2 to 5 colors (max you can select 5 colors), then click the P button again, the LED light connected to the receiver will flash again, which means the program is finished. Press the P button to start the program
- Press and hold the button to increase or decrease the light intensity of the dual colors (Tunable White)
- Play/Pause button: click to play/ pause, 10 built-in modes. Press and hold to speed up/decrease the current program.
5.3 PRE-DEFINED RGB COLOR GRADIENTS
5.4 PROGRAMMING INDIVIDUAL COLOR
GRADIENTS
STEP 1:
Press the ON/OFF button to activate the remote control
STEP 2:
Select one or more connected zone numbers (e.g. Zone 4) and press it.
STEP 3:
Press the P button, the LED lights connected to the receiver will blink once
STEP 4:
Touch the round slider (color wheel) to select 2 to 5 colors (max. you can
select 5 colors).
STEP 5:
Press the P button again to confirm the selected color, the LED lights
connected to the receiver will blink again
SCHRITT 6:
Press the > button to start the program
SCOPE OF DELIVERY AND ACCESSORIES
Each remote control is supplied with (these) instructions. It is part of the
scope of delivery for the device and must be handed over to the end user.
Important: All instructions for Barthelme products can be downloaded from
the Internet at www.barthelme.de. Please check for
updates before use!
SIMPLIFIED EU DECLARATION OF CONFORMITY:
Barthelme hereby declares that wireless equipment type 66000775 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following
Internet address:
www.barthelme.de/shared/download/CE_declaration_66000775.pdf
CONTACT
Josef Barthelme GmbH & Co. KG
Oedenberger Str. 149
90491 Nürnberg | Germany
T: +49 911 42 476 0
E: info@barthelme.de
www.barthelme.de
VERSION 03|2022
SUBJECT TO TECHNICAL CHANGES.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>