Barthelme 60 RGB IP 54 LED Strip Basic Instruction Manual
- June 13, 2024
- Barthelme
Table of Contents
BARTHELME LED STRIP BASIC
INSTALLATION AND OPERATING INSTRUCTIONS
60 RGB IP 54 LED Strip Basic
In
order to ensure proper and safe operation, it is essential to follow these
instructions!
The manual contains important information on commissioning and handling and is
an integral part of the product. Pay attention to this, even if you pass this
product on to third parties.
GENERAL INFORMATION REGARDING PROPER USE OF THE PRODUCT
The LED STRIP BASIC is a flexible LED module, which serves as a component to
manufacture luminaires for general lighting. The LED strip is to be provided
with a suitable housing during operation that meets the normative and legal
requirements for the application purpose and location and that protects the
sensitive electronic components of the flexible PCB from external influences
and ESD. When used outdoors in particular, it should be ensured that
corresponding precautions are taken to protect it against water, moisture and
salt. In addition, a sophisticated cooling of the LED strip is to be ensured.
During operation, the permissible maximum temperature of +45 °C may not be
exceeded.
Read the safety instructions carefully. The installation of the LED strip may
only be carried out by a qualified electrician!
SAFETY INSTRUCTIONS
All information in these instructions, and especially the safety instructions, must be followed at all times.
| The use of this symbol in these instructions indicates a risk of electric
shock.
---|---
| This symbol indicates general hazards or important information that must be
observed.
| The arrow symbol is used to indicate specific information or tips.
| WARNING OF ELECTRIC VOLTAGE!
IMPROPER AND UNPROFESSIONAL WORKING WHEN CONNECTING THE LED STRIP PRESENTS A
DANGER TO LIFE. THE ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED
ELECTRICIAN.
| RISK OF INJURY, RISK OF BLINDING!
THE LED STRIP SHINES VERY BRIGHTLY. LOOKING DIRECTLY AT THE LIGHT SOURCE MAY
RESULT IN EYE INJURIES.
| EXPLOSION HAZARD
THE LED STRIP BASIC MAY NOT BE OPERATED IN ENVIRONMENTS IN WHICH EXPLOSIVE OR
COMBUSTIBLE GASES, FUMES OR DUST ARE PRESENT — DOING SO CARRIES A RISK OF
EXPLOSION AND FIRE.
| In commercial establishments, observe the accident prevention regulations
issued by the federation of industrial trade associations for electrical
systems and equipment.
» The LED strip may only be operated with a suitable controller/power supply.
» Note the voltage and power specifications on the cardboard box and choose a
power source with a power reserve of at least + 20 %.
DISCLAIMER
Damage to the product resulting from failure to comply with the installation
instructions for use will void the warranty and all related claims. We also
accept no liability for damages resulting from improper use. The same applies
for property damage and personal injury caused by improper handling or non-
observance of the safety instructions.
INSTALLATION AND HANDLING INSTRUCTIONS
During installation, observe the safety regulations for the prevention of
electrostatic discharge (ESD). This is one of the most common causes of
failure in electronic components containing semiconductors. Barthelme
produces, stores and packages all LED strips in an ESD-protected environment
and uses anti-static packaging. We recommend using our ESD grounding set with
wrist strap when working with the product (item No. 50991800).
GENERAL INSTRUCTIONS FOR USE
» The LED strip may only be sharply bent once in places where no electronic
components are mounted. The minimum bending radius of the LED STRIP BASIC is
30 mm.
» Ensure that no mechanical loads are applied to the electronic components on
the LED strip.
» Ensure that the LED strip is adequately protected in areas containing water,
moisture and salt. CUTTING LED STRIPS TO THE DESIRED LENGTH
» You can use scissors (or similar) to cut the LED STRIP BASIC to the
desired length at the marked points between the solder pads.
CONNECTION AND JOINING BY SOLDERING
» After cutting an IP class protected strip, use a sharp object to remove the
potting compound so that the solder points are exposed. Ensure that you do not
damage the LED strip on the inside!
» Connect the supply line or connection cable by soldering it to the provided
solder pads.
» Note the polarity (+/- label) on the solder pads. If the polarity is
incorrect, no light will be emitted and/or the LED strip may be damaged.
» When soldering, a max. soldering time of 3 seconds and a max. soldering
temperature of 350 °C must be observed.
» When connecting multiple LED modules, observe the maximum operable length of
a combined module (see valid datasheet at
www.barthelme.de).
Correspondingly longer LED modules can be created by connecting an
(intermediate) feed at the beginning and end of the LED module.
RESTORE IP PROTECTION
» LED STRIP BASIC with IP protection have a silicone micro-coating for
protection against splash water and dew moisture. This means that Barthelme
lighting solutions can also be used in environments with high humidity or dew
(e.g. bathrooms and protected outdoor areas). Please note that when cutting
and soldering the LED strips, the IP protective layer will be damaged. To
restore full protection, the cut and soldered areas must be sealed again. A
recommendation of the protective protective coatings approved by us, can be
found at www.barthelme.de.
CONNECTION AND JOINING WITHOUT SOLDERING
» An overview of the Barthelme LED strips that can be connected or joined
together with connectors with each other, can be found at
www.barthelme.de.
» Partially remove the protective film on the back of the adhesive strip
before connecting the LED strip. Then push the LED strip into the connector
and press it closed until it fully clicks into place.
» Observe the current carrying capacity approved for the respective
connectors.
» The use of connectors is not recommended for IP-protected protected LED
strips.
INSTALLATION ON A THERMALLY CONDUCTIVE SURFACE
IMPORTANT: Before installation, test the LED STRIP BASIC for proper
functioning in the unrolled state.
Subsequent complaints about material defects cannot be accepted.
» Ensure that the installation surface is clean and free from grease, oil,
silicone and dirt particles.
» Install the LED strip on a thermally conductive substrate using the double-
sided adhesive tape on the rear. For this purpose, completely remove the
protective foil.
» Ensure that solder joints are properly insulated from the profile.
» Ensure that the maximum permissible ambient temperature of -25° to +45°C is
not exceeded during operation and that sufficient cooling is provided.
» We strongly advise against performing the installation on uneven or poorly
heat-conductive surfaces, such as plasterboard, wallpaper, wood or stone, as
this may significantly shorten the product‘s service life and adversely affect
the adhesion of the adhesive tape.
Never fasten the LED STRIP
BASIC over a profile joint! The physical expansion or contraction of the
profile in the event of temperature fluctuations may damage the LED strip. A
solution here is to cut the solder pads at the profile joint and to use
flexible connections, e.g. soldered flexible wire bridges or LED STRIP BASIC
connectors.
CONNECTION TO THE POWER SUPPLY
A constant voltage power supply is required for operation — this must be
dimensioned according to the power and voltage of the LED strip. For this
purpose, note the latest data sheet version at
www.barthelme.de
A controller is required for advanced features (e.g. dimming or colour
control). We recommend our control unit series. More information about this
can be found at www.barthelme.de
» Connect the power cable attached to the LED strip to the secondary side of
the power supply. Observe the polarity (+/-) on the LED strips and power
supply!
» Ensure sufficient dimensioning of the power supply. We recommend factoring
in a + 20% power reserve.
MAINTENANCE AND CARE
» The LED STRIP BASIC is maintenance-free.
» Should it be necessary to clean the LED STRIP BASIC due to contact with dust
or light dirt, perform dry cleaning using clean compressed air (observe the
appropriate dosage! do not spray directly onto components!) or a clean, soft
and lint-free cotton cloth.
» Cleaning with liquids or cleaning agents is strongly discouraged as this
could damage the LED strip!
TECHNICAL DATA
The specifications for the LED STRIP BASIC can be found via the corresponding data sheet. You will find the latest version at www.barthelme.de.
DISPOSAL
**** Please play your part in helping to avoid waste. Should you no longer
need this product, please keep in mind that many of its components are made
from valuable raw materials and can be recycled. Therefore, do not dispose of
it in the dustbin; instead take it to your nearest collection point for
electrical appliances. Thank you for your help!
This product complies with the requirements of the applicable European and
national regulations. Its conformity has been verified, the corresponding
declarations and documents have been recorded by the manufacturer.
VERSION 05
2023
© JOSEF BARTHELME GMBH & CO. KG Oedenberger Straße 149
90491 Nürnberg Germany
T +49 911 42476 0 F +49 911 42476 66 E
info@barthelme.de
BARTHELME.DE
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>