Barthelme 66000773 Remote Control Instruction Manual

Barthelme 66000773 Remote Control

PLEASE READ CAREFULLY AND ARCHIVE!

INTRODUCTION

• Since this remote control is an accessory of the 66000770 control unit, it can only be used in conjunction with this control unit. The operating instructions of the control unit must be observed.
• The outputs of the control unit are controlled depending on the use of the coupled remote control/touch panel. This remote control is a 1-channel device, for monochrome applications. Up to four zones can be controlled separately per remote control.
• Each control unit can be paired with up to eight different remote controls.
• Within a network all colors can be synchronized automatically. The range depends strongly on the spatial conditions; in an open field up to 50 meters are possible, indoors a reliable operation over 20 to 30 meters is normally possible without any problems.

INTENDED USE

• The remote control allows you to adjust colors or to select effects.
• It uses a button and a touch-sensitive round slider.
• The remote control uses a radio frequency that is license-free in the EU, Switzerland, Norway and Iceland.

TECHNICAL DATA

• Operating voltage: 4.5 V DC

• Batteries: 3x 1.5 V (AAA batteries)

• Protection class: III

• Dimensions (L/W/H): 120 / 55 / 17 mm

• Ambient temperature: 0 °C to max. + 40 °C

• Relative air humidity: 8 % to 80 %

• Wireless frequency: 869.5 MHz
  (license-free in the EU, Switzerland, Norway and Iceland).

• Indoor range: 20 to 30 meters

• Protection class: IP 20

SAFETY INSTRUCTIONS

In case of improper operation, modification of the device, or damage to property or persons caused by improper handling or non-observance of the safety instructions, we do not assume any liability and the warranty claim expires completely.

OPERATION

Only operate the product when it is functioning properly. In the event of a fault, switch the product off immediately and do not operate it again until it has been checked by a qualified electrician. This is the case if:

• visible damage occurs
• the product does not work properly
• there is smoke, fumes, or audible crackling noises
• overheating can be detected

COMMISSIONING
Insert suitable batteries (3x 1.5 V, AAA batteries) into the remote control (back) and pair it with the control unit.

• STEP 1:
  Wire the RF receiver according to the wiring diagram (please refer to the instructions of the RF receiver with which you want to pair the device)

• STEP 2:
  Press the ON/OFF button to activate the remote control RF-LED Receiver Learning Key

• STEP 3:
  Press the „learning key“ on the RF receiver or switch on the receiver three times in succession to set it to the connection status

• STEP 4:
  Select and press a zone number (e.g. zone 4)

• STEP 5:
  Touch the round slider. When the LED lights connected to the wireless receiver flash once, it means that the receiver is successfully connected to Zone 4

IF SEVERAL CONTROL UNITS ARE USED, THIS PROCEDURE MUST BE PERFORMED ON EACH CONTROL UNIT.

KEY ASSIGNMENT / FUNCTION

1. White channel“ = the 4th channel. Press to turn on and off, press and hold to increase or decrease the light intensity of the „W channel“.

2. Press and hold to reduce the light intensity of the RGB channels

3. Press to turn on/off all zones

4. Press to play or stop the 10 built-in effects. Press and hold to speed up or reduce the running effect

5. Displays the status of the remote control

6. Round slider (color wheel)

7. Zone numbers: Press to select zone(s), press and hold to turn the corresponding zone on or off

8. Press and hold to increase the light intensity of the RGB channels

9. Press to control cool white, normal white or warm white mixed by RGB.
   Double click to disable the RGB channels

10. Press and hold to save colors. Press it to recall the saved colors again

PRE-DEFINED RGB COLOR GRADIENTS

SAVING THE CURRENT SETTINGS

• STEP 1:
  Press the ON/OFF button to activate the remote control

• STEP 2:
  Select one or more connected zone numbers (e.g. Zone 4) and press it.

• STEP 3:
  Touch the round slider (color wheel) or press the other buttons to select the desired scene.

• STEP 4:
  Press and hold any scene button from S1 to S3 (e.g. S3), the LED lights connected to the RF receiver will flash once, which means the color/scene has been saved successfully

RECALL THE SAVED SETTINGS

• STEP 1:
  Press the ON/OFF button to activate the remote control

• STEP 2:
  Select one or more connected zone numbers (e.g. Zone 4) and press it.

• STEP 3:
  Press any scene button from S1 to S3 (e.g. S3) to recall the saved scene

SCOPE OF DELIVERY AND ACCESSORIES

Each remote control is supplied with (these) instructions. It is part of the scope of delivery for the device and must be handed over to the end user.
Important: All instructions for Barthelme products can be downloaded from the Internet at www.barthelme.de. Please check for updates before use!

SIMPLIFIED EU DECLARATION OF CONFORMITY:
Barthelme hereby declares that wireless equipment type 66000773 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: www.barthelme.de/shared/download/CE_declaration_66000773.pdf

CONTACT

• Josef Barthelme GmbH & Co. KG
• Oedenberger Str. 149
• 90491 Nürnberg | Germany
• T: +49 911 42 476 0
• E: info@barthelme.de
• www.barthelme.de

References

• Barthelme - LED SOLUTIONS | Startseite
• barthelme.de/shared/download/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>