Nedis BTLS20RGBW Smart Bluetooth USB LED Strip User Manual
- June 5, 2024
- nedis
Table of Contents
BTLS20RGBW Smart Bluetooth USB LED Strip
User Manual
Preface
Thank you for purchasing the Nedis BTLS20RGBW.
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
Intended use
This product is a Smart Bluetooth USB LED strip that can be controlled by smartphone.
The product is not intended for professional use.
The product is intended for indoor use only.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Specifications
Product
|
Smart Bluetooth USB LED Strip
---|---
Article number
|
BTLS20RGBW
LED strip length
|
2 m
LED strip width
|
12 mm
Brightness
|
900 lm
Light colour
|
RGB + 2700K
LED type
|
5050 + 2835
LED quantity
|
2 x 30 per meter
Connection
|
5 pins at 2 mm each
Power
|
5 W
Waterproof
|
IP20
Energy class
|
F
Main parts (image A)
A
1. USB cable
2. LED strip
3. LED strip connector
Safety instructions
WARNING
- Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep the packaging and this document for future reference.
- Only use the product as described in this document.
- Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
- Do not drop the product and avoid bumping.
- This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
- Only use the provided power cable.
- Do not expose the product to water or moisture.
Explanation of the symbols on the product or packaging
Icon
|
Description
---|---
|
Product in which protection against electric shock does not rely on basic insulation only, but in which additional safety precautions such as double insulation or reinforced insulation are provided, there being no provision for protective earthing or reliance upon installation conditions. NOTE A Class II products may be provided with means for maintaining the continuity of protective circuits, provided that such means are within the product and are insulated from accessible surfaces according to the requirements of Class II.
|
Indication to explain the product is suitable for indoor use only.
|
Electronic equipment needs to bear the CE mark in order to be marketed in the EU. CE marking shows that a product is assessed before being placed on the market and that it meets EU safety, health and environmental protection requirements. CE marking is also sometimes accepted as a means of compliance with type-approval requirements; for example, electronic components that require type-approval and also CE marking for electromagnetic compatibility (EMC) or low-voltage equipment.
|
Indication to explain that the product needs to be collected separately when disposed. Do not throw in the trash bin.
Installation
- Check the contents of the package
- Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Installing the app
1. Download the Nedis Smartlife app for Android or iOS on your phone via Google Play or the Apple App Store.
2. Open the Nedis Smartlife app on your phone.
3. Create an account with your mobile phone number or your e-mail address and tap Continue.
4. Enter the received verification code.
5. Create a password and tap Done.
6. Tap Add Home to create a SmartLife Home.
7. Set your location, choose the rooms you want to connect with and tap Done.
Connecting the product
1. Align the arrow on the LED strip connector A3 to the +5V sign on the LED strip A2.
2. Plug A3 into A2.
3. Plug the USB cable A1 into a power source.
- A2 blinks.
- If A2 does not blink, disconnect and reconnect A1 from the power source three times until A2 starts to blink.
4. Enable Bluetooth on the device you want to pair.
5. Tap + in the top right corner.
6. Under _ Search Device, _select the product from the list of available devices.
7. Rename the product after it has been found and added.
Setting up the product
1. Unplug A1 from the power source.
2. Clean the surface from dust and grease.
- The surface must be smooth. Do not place the product on knitted/wool fabrics, dust wall, rough plastic surface or frosted glass.
3. Remove part of the 3M tape from the back of A2.
4. Place the start of A2 in the desired position.
- Make sure the power source is within reach.
5. Unroll A2.
6. Remove the 3M tape and press A2 into the desired position.
7. Firmly press A2 down with your hand.
- Do not use hard objects to press A2 down to prevent damage.
- Only fold/bend A2 around the cut lines to prevent damage to the components
- If desired, cut A2 to size on the indicated cut lines.
8. Plug A1 into a power source.
Use
Controlling the product
1. Use the app to change modes, speed, LED colour, and LED brightness.
Maintenance
- Before cleaning and maintenance, switch off the product and disconnect the power. Let the product cool down.
- Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
- Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.
Warranty
Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.
This product is designed for private use (normal domestic use) only. Nedis is not responsible for wear, defect and/or damages caused by commercial use of the product.
Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.
Disposal
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
---|---
Declaration of Conformity
We, Nedis B.V. declare as manufacturer that the product BTLS20RGBW from our brand Nedis®, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.
The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via:
For additional information regarding the compliance, contact the customer service:
Web: www.nedis.com
E-mail: service@nedis.com
Phone: +31 (0)73-5991055 (during office hours)
Nedis B.V., de Tweeling 28
5215 MC ’s-Hertogenbosch, the Netherlands
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>