Progress P400311 Burgess 4-Light Matte Black Farmhouse Chandelier Instruction Manual
- June 8, 2024
- PROGRESS
Table of Contents
P400311 Burgess 4-Light Matte Black Farmhouse Chandelier
Instruction Manual
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Glass shade | 4 |
| C | Socket ring | 4 |
HARDWARE CONTENTS (not actual size)
THANK YOU for selecting Progress Lighting
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To
clean, wipe with damp cloth. Do not use abrasive
cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown.
You now need to adjust the screw length according to the fixture canopy depth. -
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Lift up the fixture and pass the screws (AA) through the two mounting hole in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step 5.
Next, take the fixture
down and go back and tighten the hex nuts (DD) up against the mounting plate
(CC).
You now should have the correct length of threads for mounting the fixture.
NOTE: During this
step, determine the hanging length of your fixture by removing chain links and
stems, optionally cutting the electrical and ground wire to length.
Do NOT cut electrical or ground wires until this overall length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy loop (GG) to allow for easy connections in step 4.
(Chain links can be spread open with 2 pairs of pliers. Twist the split link ends in opposite directions and close by squeezing them back together.) -
Once hanging length is determined, pass wires through stems (HH/JJ) and nipples (KK), tightening stems to assembly as you go to avoid twisting the wires. Pass wires through chain loop (GG) and tighten chain loop (GG) to stem assembly (HH).
Open chain link at one
end of chain (FF). Hook the open chain link (FF) onto the chain loop (GG).
Close the chain links back together with the pliers. open the quick link (LL),
attach chain link the other end of chain (FF) and canopy loop (GG) onto the
quick link (LL). Close the quick link. You can now weave the wires through
every third chain link (FF) and up through the canopy loop (GG). -
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
-
Pass the screws (AA) through the two holes in the canopy (A). Secure the fixture to the screws (AA) using the two cylinder nuts (EE). Tighten securely.
-
Attach the glass shade (B) to the fixture (A) using the socket ring (C) to secure it tightly. Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base, SBCFL or SBLED.
WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed
and under normal conditions of use, are warranted to our customers only to be
free from defects in material and workmanship at time of shipment. All
warranty claims must be asserted within one year from date of purchase of the
subject items; thereafter, warranty claims will not be honored. Customers’
sole remedy for a warranty claim or otherwise shall be limited to repair or
replacement of the subject product if it is shown to have been defective in
material or workmanship at time of shipment. Progress’s sole and maximum
liability for a defective product shall never exceed the cost of the subject
product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE
EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS
OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE
LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR
OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE
ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE
CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer’s sole
and exclusive remedy against us for breach of the warranty, breach of contract
or negligence or strict liability or otherwise shall be limited to repair or
replacement of the subject product at our option (excluding installation and
removal charges which shall not be our liability) or, if we choose, refund of
the purchase price. In no case does our warranty and exclusive remedy extend
to anybody other than our customers. Our customers are not authorized to
extend warranties or remedies on our behalf to anyone. Such unauthorized
extensions of warranties or remedies by the customer shall remain customer’s
responsibility. Customer is responsible for determining the suitability of
our products for customer’s use or resale, or for incorporating them into
objects or for applications which customer designs, assembles, constructs or
manufactures.
93164434
We can assist you with questions regarding product information, assembly or
missing parts
800-447-0573
8am-8pm (Eastern), Monday-Friday
customerservice@progresslighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>